Craftsman CMCD750 Right Angle Drill User Manual

Content

Craftsman CMCD750 Right Angle Drill Manual

Introduction

The Craftsman CMCD750 Right Angle Drill is a cordless V20 power tool designed for drilling and fastening where a conventional drill cannot fit. Its compact right-angle design provides access in narrow spaces such as between wall studs, inside cabinets, beneath sinks, and around plumbing or electrical installations. The approximately 3.5-inch head profile helps users work closer to surrounding surfaces while maintaining a familiar drill-like control layout.

This 3/8-inch right angle drill combines a two-speed transmission, variable-speed multi-grip trigger, and LED work light. Together, these features support controlled drilling, screwdriving, and light-duty construction or maintenance tasks. The two-speed gearbox allows users to select a slower setting for increased control and a faster setting for routine drilling and fastening. Variable trigger control helps reduce stripped fasteners and improves accuracy when starting a hole.

The tool is intended for homeowners, remodelers, maintenance workers, cabinet installers, plumbers, electricians, and DIY users who regularly work in confined areas. It is especially useful when a standard cordless drill is too long or difficult to position. The CMCD750 is a tool-only model, so a compatible V20 battery and charger are required for operation. Always read the manufacturer’s manual before use and select accessories appropriate for the material and task.

Craftsman CMCD750 Right Angle Drill Specifications and Features

Product type: Cordless right-angle drill for drilling and fastening.
Platform: Craftsman V20 cordless system.
Chuck size: 3/8-inch chuck for compatible drill and driver accessories.
Head profile: Approximately 3.5 inches for improved access in tight workspaces.
Transmission: Two-speed gearbox for controlled fastening and drilling performance.
Power output: Up to 300 UWO, according to the manufacturer’s product information.
Speed control: Variable-speed multi-grip trigger for gradual starts and improved hand positioning.
Lighting: Integrated LED light to illuminate the immediate work area.
Power source: Compatible 20V MAX battery; battery and charger are sold separately on tool-only configurations.
Voltage note: 20V MAX refers to maximum initial battery voltage measured without a workload; nominal voltage is 18V.
Typical applications: Wood drilling, light fastening, cabinet work, maintenance, and installation in confined spaces.

How to Set Up the Craftsman CMCD750 Right Angle Drill

Inspect the drill, chuck, battery, and accessory for damage. Do not use cracked, bent, or excessively worn components.
Charge a compatible V20 battery using the correct Craftsman charger. Allow the battery to cool if it is unusually hot before charging.
Remove the battery before installing an accessory. Open the 3/8-inch chuck, insert the bit fully, and tighten the chuck securely.
Select the appropriate gear. Use the lower-speed setting for controlled fastening or larger bits, and the higher-speed setting for routine drilling with suitable accessories.
Insert the charged battery until it locks into place. Confirm that it is secure before operating the trigger.
Press the trigger gradually while keeping the bit aligned with the work surface. Use the integrated LED to improve visibility in dark areas.
Release the trigger completely before changing direction, removing the battery, or adjusting the chuck.

For safe operation, wear eye protection, secure the workpiece, keep hands away from rotating parts, and avoid loose clothing. Remove the battery before maintenance or accessory changes. If the tool does not start, remove and reinstall the battery, check its charge, and verify that the forward/reverse selector is centered correctly.

Craftsman CMCD750 Troubleshooting Guide

Drill does not start

Check that the battery is charged and fully seated. Inspect the battery contacts for dirt or damage. Make sure the forward/reverse selector is set to forward or reverse rather than the center lock position. If the tool still does not operate, test it with a known-compatible battery.

Bit slips in the chuck

Remove the battery, open the chuck, and reinstall the accessory straight and fully. Tighten the chuck firmly by hand. Do not use a damaged bit or operate the drill with an accessory that is not rated for the selected speed.

Drill stalls or runs slowly

Reduce trigger pressure, select the appropriate gear, and use a bit designed for the material. Excessive force can overload the motor. Allow the tool to cool if the housing becomes unusually hot, and avoid repeatedly forcing large accessories through dense material.

LED light does not illuminate

Confirm that the battery is installed and the trigger is being pressed. If the drill operates but the LED remains off, discontinue use if additional electrical symptoms appear and arrange service.

Error codes and support

The available product information does not identify user-facing CMCD750 error codes. Record the model and serial number and consult the official manual before attempting repairs. For warranty, parts, manuals, or service assistance, contact CRAFTSMAN customer service at 888-331-4569 or use the manufacturer’s online support options. Keep proof of purchase because warranty requirements can vary by product and region.

Craftsman CMCD750 Pros and Cons

Advantages

Access in confined areas: The compact right-angle head is more practical than a standard drill for work between studs, inside cabinets, and beneath fixtures.
Flexible hand positioning: The multi-grip trigger supports several holding positions, which can improve control when the tool is oriented horizontally or vertically.
Useful speed selection: The two-speed transmission allows users to prioritize control for fastening or speed for appropriate drilling tasks.
Improved visibility: The integrated LED helps illuminate the immediate drilling area.
Shared battery platform: Owners of compatible V20 tools may be able to use existing batteries, subject to compatibility and charge requirements.

Limitations

Tool-only configuration: A compatible battery and charger may be needed separately.
Limited chuck capacity: The 3/8-inch chuck is suited to common drilling and fastening accessories but is not intended for every large-bit application.
Not a heavy-duty replacement: The drill is best for access-focused drilling and fastening, while high-load masonry, large-hole, or continuous industrial work may require a specialized tool.
Battery dependence: Runtime varies with battery capacity, material, accessory size, speed setting, and workload.

The Craftsman CMCD750 Right Angle Drill is best suited to users who value compact access and cordless convenience. Choose another drill type when maximum torque, hammer action, large-diameter drilling, or extended heavy-duty operation is the primary requirement.

PDF

Faqs

How do I set up the Craftsman CMCD750 Right Angle Drill for the first time?

Confirm that the drill is switched off, then insert a charged CRAFTSMAN V20 battery until it locks securely. Select the appropriate two-speed setting before squeezing the variable-speed trigger. Open the 3/8-inch keyless chuck, insert the bit straight, and tighten the chuck by hand. Test the drill briefly in a clear area, checking that the bit runs smoothly and the forward/reverse selector is positioned correctly.

Which batteries and accessories are compatible with the Craftsman CMCD750 Right Angle Drill?

The Craftsman CMCD750 Right Angle Drill is designed for the CRAFTSMAN V20 battery platform. The tool-only package does not include a battery or charger, so use a compatible V20 lithium-ion battery and charger. Its 3/8-inch keyless chuck accepts drill bits and fastening accessories with suitable shank sizes. Choose accessories rated for the material and speed being used, and avoid forcing oversized bits.

Why is my Craftsman CMCD750 Right Angle Drill not starting?

Remove and reinstall the battery firmly, ensuring it is fully charged and seated until the release tabs engage. Check that the forward/reverse selector is centered or not accidentally positioned between settings, then move it decisively to forward or reverse. If the LED does not illuminate and the trigger remains unresponsive, try another compatible charged battery. Stop using the drill if the battery, contacts, or housing appears damaged.

How can I prevent the Craftsman CMCD750 Right Angle Drill from overheating?

Use the correct speed setting and let the drill do the work instead of applying excessive pressure. Withdraw the bit periodically when drilling deep holes to clear debris and reduce friction. Use sharp bits designed for the material, and allow the motor to cool between demanding tasks. If the housing becomes unusually hot, smells of burning, or loses power, release the trigger, remove the battery, and inspect the bit and workpiece.

What do the two speed settings on the Craftsman CMCD750 Right Angle Drill do?

The two-speed transmission helps match drill behavior to the task. Use the lower setting when you need increased control and torque for larger bits, driving fasteners, or starting holes. Use the higher setting for faster drilling with smaller bits in suitable materials. Change speeds only when the drill is stopped, and combine the selected gear with gentle trigger control to prevent bit slipping or stripped fasteners.

How do I stop the chuck from slipping on the Craftsman CMCD750 Right Angle Drill?

Remove the battery before inspecting the chuck. Open the keyless chuck, clean dust or debris from the jaws and bit shank, then insert the accessory straight and tighten the chuck firmly by hand. Do not use a damaged, bent, or undersized bit. If slipping continues, check for worn chuck jaws or a damaged shank. Do not disassemble the chuck unless the model manual specifically provides that procedure.

How can I use the Craftsman CMCD750 Right Angle Drill safely in tight spaces?

Mark the drilling location first and confirm that hidden wiring, plumbing, or other obstacles are not behind the surface. Select a bit suitable for the material, hold the multi-grip handle securely, and keep both hands clear of the rotating chuck. Start slowly to prevent wandering, then increase speed as the bit tracks correctly. The compact right-angle head helps reach confined areas, but it does not replace proper clearance and eye protection.

How should I clean and maintain the Craftsman CMCD750 Right Angle Drill?

Remove the battery before cleaning or inspection. Wipe the drill with a dry or slightly damp cloth, and brush dust from the chuck, ventilation openings, trigger area, and battery contacts. Do not immerse the tool or spray cleaners into its housing. Store it in a dry place without a bit installed, protect it from extreme temperatures, and inspect the cord-free housing, chuck, battery, and accessories before each use.