Dji Avata 2 Aircraft WM170 User Manual

Content

DJI Avata 2 Aircraft WM170 Manual and User Guide

The DJI Avata 2 Aircraft WM170 is a compact first-person-view camera drone designed for immersive flight, agile movement, and stabilized aerial video. Its integrated propeller guards improve protection during close-proximity flying, while the FPV system provides a direct, low-latency view through compatible DJI Goggles and a supported motion controller or FPV remote controller.

With a lightweight body, built-in storage, electronic image stabilization, and multiple flight modes, the Avata 2 suits beginners learning FPV flight as well as experienced pilots creating dynamic travel, action, real-estate, and indoor-style footage. Normal mode provides a controlled flying experience, Sport mode increases responsiveness, and Manual mode is intended for trained pilots who understand throttle management and unrestricted aircraft movement.

The drone must be operated with compatible DJI goggles and a supported controller. DJI Fly is required for activation, device linking, firmware updates, and selected configuration tasks. Before every flight, inspect the propellers, motors, battery, camera area, and propeller guards. Fly only where permitted, maintain visual awareness of the operating environment, and avoid people, animals, power lines, water, and severe weather.

This guide explains the DJI Avata 2 WM170 specifications, setup procedure, routine care, safety precautions, and practical troubleshooting steps for reliable daily use.

DJI Avata 2 WM170 Specifications and Features

Aircraft type: Compact FPV camera drone with integrated propeller guards.
Approximate takeoff weight: 377 g.
Dimensions: Approximately 185 × 212 × 64 mm.
Intelligent Flight Battery: 2,150 mAh Li-ion battery.
Battery energy: Approximately 31.7 Wh.
Battery standard voltage: 14.76 V.
Maximum charging voltage: 17 V.
Typical maximum flight time: Approximately 23 minutes under controlled test conditions.
Maximum horizontal speed: 8 m/s in Normal mode, 16 m/s in Sport mode, and up to 27 m/s in Manual mode when conditions and local regulations allow.
Maximum ascent speed: Up to 6 m/s in Normal mode.
Maximum takeoff altitude: Approximately 5,000 m above sea level.
Internal storage: Approximately 46 GB, with support for a compatible microSD card.
Transmission range: Dependent on region, regulatory limits, interference, and operating conditions.
Control requirement: Compatible DJI Goggles and a supported DJI motion controller or FPV remote controller.

Detailed DJI Avata 2 Aircraft WM170 Description

The DJI Avata 2 WM170 combines a ducted FPV aircraft design with a stabilized camera system. The camera captures the forward view while the goggles display a live first-person perspective. A motion controller supports intuitive directional flight, while the DJI FPV Remote Controller 3 enables traditional two-stick control and Manual mode for qualified pilots.

The aircraft body is built around a compact, lightweight frame with integrated guards surrounding the propellers. These guards help reduce damage from incidental contact but do not make the drone safe to fly near people or obstacles. Flight sensors, positioning systems, and automatic braking features assist with controlled operation, but pilots remain responsible for navigation.

Typical applications include cinematic fly-throughs, outdoor action footage, landscape videos, event-production shots, and learning FPV flight skills. For routine care, remove the battery after use, inspect the propellers for chips or bends, and use a soft, dry brush or lint-free cloth to remove dust. Do not use solvents, pressurized air at close range, or liquids near the motors, camera, battery contacts, or USB-C port.

How to Set Up DJI Avata 2 WM170 for First Flight

Charge the aircraft battery, goggles, and controller with suitable USB-C equipment. The aircraft battery must be activated by charging before its first use.
Install the battery securely in the aircraft and confirm that it is not swollen, cracked, wet, or damaged.
Inspect the propellers and verify that each propeller type is installed on the matching motor position. DJI Avata 2 uses clockwise and counterclockwise propellers.
Power on the aircraft, goggles, and controller by pressing the power button once and then pressing and holding it.
Connect the goggles to a compatible mobile device, open DJI Fly, and follow the activation prompts.
Complete device pairing or linking according to the on-screen instructions. Keep the aircraft and controller close together during this process.
Install available firmware updates before flight. Restart all devices if an update fails, then retry using a stable connection.
Select Normal mode for the first flight. Use Sport mode only after practicing basic control, and use Manual mode only after dedicated training.
Choose an open, legal flight area and confirm that the aircraft has adequate positioning information, battery charge, and a clear return path.

Never start the motors with loose clothing, hands, hair, or objects near the propellers. Do not fly indoors or in confined spaces until you understand the controls and obstacle risks.

DJI Avata 2 Troubleshooting Guide

Battery will not operate before the first flight

Charge the Intelligent Flight Battery to activate it. Check that the battery is correctly seated and that the charging equipment is connected securely. Do not use a battery showing swelling, leakage, physical damage, or abnormal heat.

Aircraft, goggles, or controller will not connect

Power off all devices, restart them, and place them close together. Confirm that the correct controller is being used, then repeat the linking process. Keep the goggles connected to the mobile device when DJI Fly requests activation or configuration.

Firmware update fails

Use a stable internet connection, ensure every device has sufficient battery power, and retry the update. If the failure continues, restart the aircraft, goggles, and controller before attempting the update again.

Gimbal or camera view appears unstable

Land safely, inspect the camera area for debris or impact damage, and perform the available IMU or compass calibration through DJI Fly when prompted. Avoid flying near strong magnetic interference.

Short flight time or unexpected battery warning

Wind, high speed, cold temperatures, aggressive maneuvering, and repeated acceleration reduce flight time. Fully charge the battery, allow it to reach a suitable operating temperature, and land immediately when the app or goggles display a low-battery warning.

Support and warranty assistance

For unresolved faults, record the device status, firmware version, and any on-screen message. Contact DJI Support or an authorized DJI service center through the official DJI support channel. Warranty duration and service requirements vary by product, component, and region; retain proof of purchase.

DJI Avata 2 WM170 Pros and Cons

Advantages

Immersive FPV operation: Goggles-based flight provides a direct first-person view that is more engaging than conventional line-of-sight camera drones.
Protected aircraft layout: Integrated propeller guards offer additional protection during careful proximity flying.
Accessible controls: A compatible motion controller makes basic FPV movement easier for new pilots than traditional manual controls.
Multiple flight modes: Normal and Sport modes support progressive learning, while Manual mode provides advanced control for experienced pilots.
Built-in recording capacity: Internal storage reduces the risk of missing footage because a memory card was not installed.
Portable design: The compact body is convenient for travel, outdoor filming, and quick setup.

Limitations

Requires compatible accessories: The aircraft is not designed to operate as a standalone camera drone without supported goggles and a controller.
Limited flight endurance: Actual flight time varies considerably with wind, speed, temperature, and maneuvering.
Learning curve: Sport and especially Manual mode require practice, simulator training, and careful throttle control.
Obstacle limitations: Propeller guards reduce some contact risk but do not replace safe piloting or complete obstacle avoidance.
Best suited for: Pilots seeking immersive FPV footage, agile flight, and a structured path from beginner to advanced control.
Consider another category if: The priority is automated photography, long endurance, quiet operation, or a conventional handheld-style flight experience.

PDF

Faqs

How do I set up the dji Avata 2 Aircraft WM170 for the first time?

Charge the aircraft battery, goggles, and controller before setup. Install the DJI Fly app on a compatible phone, connect the phone to the goggles by USB-C, and follow the activation prompts. An internet connection is required for activation. Power on the aircraft, goggles, and controller, then confirm that they are linked. Complete firmware updates and read the on-screen safety prompts before the first flight.

Which goggles and controllers are compatible with the dji Avata 2 Aircraft WM170?

The dji Avata 2 Aircraft WM170 requires compatible DJI goggles and a supported controller. DJI Goggles 3 and DJI Goggles N3 work with DJI RC Motion 3 and DJI FPV Remote Controller 3. DJI Goggles 2 and DJI Goggles Integra use DJI RC Motion 2 and DJI FPV Remote Controller 2. Confirm the exact combination before purchasing accessories, because controller and goggles generations are not interchangeable in every configuration.

What should I do if dji Avata 2 Aircraft WM170 will not connect to the goggles or controller?

First, fully charge and restart the aircraft, goggles, and controller. Keep the devices close together and confirm that the selected goggles and controller are compatible with the dji Avata 2 Aircraft WM170. If linking still fails, connect each device to DJI Assistant 2 and install available firmware updates. Then repeat the linking procedure from the goggles or DJI Fly app. Remove nearby wireless interference and avoid interrupting the process.

Can I fly the dji Avata 2 Aircraft WM170 without goggles or a remote controller?

No. The dji Avata 2 Aircraft WM170 is an FPV drone designed to operate with compatible DJI Goggles and a supported DJI controller. A phone running DJI Fly is used for activation, setup, and certain settings, but it does not replace the goggles and flight controller. Before flying, verify that all three devices are powered on, linked, updated, and displaying normal battery and signal status.

How can I improve the flight performance of dji Avata 2 Aircraft WM170?

Use a fully charged, properly installed battery and update the aircraft, goggles, and controller firmware before flying. Choose an open area away from buildings, trees, power lines, and strong radio interference. Keep the aircraft within visual and transmission range, and select an appropriate flight mode for your experience. Smooth control inputs, gradual turns, and avoiding unnecessary high-speed maneuvers can improve stability, battery efficiency, and video quality.

Why is the video feed from dji Avata 2 Aircraft WM170 blurry, delayed, or unstable?

Check whether the goggles are receiving a strong transmission signal and move to a more open location with fewer obstructions. Keep the aircraft’s antennas unobstructed and avoid flying behind thick walls, metal structures, or dense vegetation. Restart the aircraft and goggles if the image remains abnormal, then check for firmware updates. A dirty camera lens can also reduce image clarity, so clean it gently with a suitable microfiber cloth.

How should I replace and maintain the propellers on dji Avata 2 Aircraft WM170?

Inspect the dji Avata 2 Aircraft WM170 propellers before every flight for cracks, bending, chips, or excessive wear. Replace damaged propellers rather than attempting to repair them. The aircraft uses clockwise and counterclockwise propellers, so install each type on the motor position specified in the manual and match the markings correctly. Tighten screws securely without overtightening, and perform a low-altitude hover test after replacement.

What maintenance should I perform after flying the dji Avata 2 Aircraft WM170?

Power off the aircraft and remove the battery before inspection. Check the propellers, motors, camera, frame, and battery contacts for dirt or damage. Use a soft, dry brush or microfiber cloth, and keep moisture away from electronic openings. Allow a warm or damp aircraft to dry completely before storage. Store batteries at an appropriate charge level in a cool, dry place, and update the aircraft and accessories periodically through DJI software.