Installation: Emerald Planet EP-FL-70S LED Floodlight Slimline Series User Manual

Content

Overview

The EP-FL-70S LED Floodlight Slimline Series is a compact sensor-ready floodlight designed for indoor and outdoor use. It suits installations where a slim profile, adjustable beam direction, and motion-sensor control are useful, such as entryways, service areas, loading zones, and perimeter lighting.

This model is intended for professional installation and works best where automatic lighting control and dependable illumination are needed in a wide range of ambient conditions.

Specifications

Model: EP-FL-70S
Power rating: 70W
Supply: AC 220-240V, 50/60Hz
Dimensions: 290 x 190 x 40 mm
Operating temperature: -20°C to 40°C
Use: Indoor and outdoor

Detailed Description

The EP-FL-70S LED Floodlight Slimline Series combines a slim housing with a mounting bracket and adjustable beam angle. After installation, the light can be aimed by loosening or adjusting the screws that control the head position, allowing the beam to be directed where coverage is needed most.

The remote control functions are centered on sensor behavior rather than full manual dimming. Users can switch the motion sensor on or off, choose from fixed preset scenes, set the hold time, set the daylight threshold, adjust detection range, and activate a test mode. The sensor settings are designed to balance automatic activation with control over when the light responds to movement and ambient light.

Safety

Installation and maintenance must be handled by a licensed electrician. Power must be isolated before any work begins to reduce the risk of electric shock or equipment damage.

The floodlight should only be used within the stated temperature range and in indoor or outdoor locations that suit the fixture’s rating. Correct isolation, wiring, and mounting are essential for safe long-term operation.

Setup and Operation

Installation steps

Turn off power at the source.
Drill two holes in the mounting surface.
Fasten the bracket to the mounting surface.
Plug in the unit.
Restore power.
Confirm that the luminaire turns on.
Adjust the beam direction by changing the screw position.

Once installed, the light is ready for normal operation and sensor-based control. The beam can be fine-tuned after power is restored, which makes it easier to target paths, doors, or work areas without remounting the fixture.

Remote control functions

Power: turns the light on or off.
Indicator light: shows that a button press has been registered and the remote is active.
Sensor ON: activates the sensor before using presets or saving sensor settings.
Sensor OFF: disables the sensor so the lights remain on permanently.
Preset scenes: four fixed programs are built in for different lighting behaviors.
Hold time: sets how long the light stays at full output when no motion is detected.
Daylight sensor: sets the ambient light level required before the light will switch on.
Detection range: changes sensor sensitivity from 100% to 50%.
Test button: places the fixture in test mode.

Sensor mode must be enabled before saving or using existing sensor settings. When selecting a preset scene, Sensor ON should be pressed first so the chosen setting is stored correctly.

Default settings

Detection range: 100%
Hold time: 20 minutes, with ON/OFF only
Daylight sensor: 150 lux

Preset scenes

Scene 1: 1 minute hold time, 50 lux daylight level, 100% output
Scene 2: 1 hour hold time, 300 lux daylight level, 50% output
Scene 3: 10 minutes hold time, 150 lux daylight level, 100% output
Scene 4: 30 minutes hold time, 50 lux daylight level, 100% output
Test mode: 5 seconds hold time, daylight sensor off, 100% output

The daylight sensor setting determines whether the floodlight responds to movement based on surrounding brightness. With the sensor active, the lamp only turns on when ambient light drops below the selected lux level. Using the OFF daylight setting keeps the fixture on when motion is detected regardless of ambient conditions.

Pros & Cons

Pros

Compact slimline design that suits modern installations
Useful sensor controls with preset scenes and test mode
Indoor and outdoor suitability
Adjustable beam direction for targeted coverage

Cons

Requires licensed electrical installation
Sensor settings must be managed carefully to save correctly
No handheld-style setup; mounting and wiring are fixed-installation tasks

PDF

Faqs

How do I install the EP-FL-70S LED Floodlight Slimline Series safely?

Installation should be done by a licensed electrician, with the power isolated before any work begins. The manual’s sequence is straightforward: turn off power at the source, drill two holes in the mounting surface, fasten the bracket, plug in the unit, restore power, and confirm the light comes on. Once installed, the beam direction can be adjusted using the screws. This floodlight is designed for indoor and outdoor use in temperatures from -20°C to 40°C.

What power supply does the EP-FL-70S floodlight require?

The EP-FL-70S LED floodlight is rated for AC 220–240V at 50/60Hz and uses 70W. That makes it suitable for standard mains-powered lighting setups, but the connection should still be handled by a qualified electrician. Before wiring or mounting, make sure the circuit is fully isolated. Using the correct supply helps the floodlight operate reliably and reduces the risk of electrical issues during installation or later maintenance.

How do I set up the remote control sensor functions on the EP-FL-70S?

The remote control offers sensor modes, presets, hold times, daylight sensing, and detection range adjustment. Sensor ON must be pressed before using sensor settings or saving preset scenes. Sensor OFF keeps the lights on permanently. The daylight sensor controls when motion triggers the light based on ambient light, and the detection range can be adjusted from 100% down to 50%. The light also includes a test mode for quick checking.

Why is the sensor not working after I change the EP-FL-70S settings?

A common reason is that Sensor ON was not pressed before selecting or saving the settings. The manual notes that the sensor must be active to store existing sensor configurations. Also check whether Sensor OFF was selected, because that mode disables sensor-triggered behavior and keeps the light on continuously. If testing a new setup, use the test button first, then reselect your preferred preset and confirm the ambient light level matches the chosen lux threshold.

What do the preset scenes do on the EP-FL-70S LED Floodlight?

The remote includes four fixed preset scenes plus a test mode. Each preset combines a different hold time and daylight threshold to suit different lighting needs. For example, one scene uses a short one-minute hold time, while another uses a longer one-hour hold time. Some presets keep the output at full brightness, while one reduces it to half power. These options let you tailor the floodlight for security, pathways, or general outdoor motion lighting.

How do I adjust the motion detection range on the EP-FL-70S floodlight?

Detection sensitivity can be changed with the remote control from 100% down to 50%. A higher setting gives the sensor a wider, more responsive detection area, which is useful for driveways, entrances, or larger spaces. A lower setting can help reduce unwanted triggers from passing cars, trees, or distant movement. If the floodlight reacts too often, lower the range; if it misses activity, increase it and test again in the installed position.

Can the EP-FL-70S be used outdoors in all weather conditions?

The EP-FL-70S is suitable for both indoor and outdoor use, but only within the specified ambient temperature range of -20°C to 40°C. That means it is built for typical exterior installations, but it should still be mounted in a location that avoids conditions outside its rated operating range. As with any outdoor floodlight, correct installation and secure mounting are important for reliable performance and safe long-term use.

How do I troubleshoot the EP-FL-70S if the light does not turn on?

Start by checking the power supply and confirming the circuit was restored after installation. Then verify that the remote settings are correct, especially Sensor ON versus Sensor OFF. If the light is in sensor mode, make sure the ambient light is low enough for the chosen lux setting to allow activation. Also confirm the unit was installed correctly, the bracket is secure, and the beam or sensor is not blocked by the mounting position.