Installation: Episode Accessories Instruction Manual

Overview

Episode Accessories are installation components designed to simplify the placement, support, enclosure installation, and finishing of compatible in-ceiling and in-wall speakers. They are intended for professional installers, home theater builders, and DIY users preparing speaker locations during new construction or remodeling.

The accessory range includes pre-construction brackets, rear enclosures for Signature speakers, edge plates, grille adapters, and several grille styles. Using the correct accessory helps establish accurate cutout locations and provides dependable speaker support.

Specifications

• Yellow bracket: IC-4
• Green bracket: IC-6 and IW-6
• Red bracket: IC-8, IW-8, and Point-6 models using the IC-8 cutout
• Blue bracket: IWLCR-6
• IC-4 cutout: 6.2 inches
• IC-6 cutout: 8.3 inches
• IC-8 cutout: 9.7 inches
• IW-6 cutout: 11.7 by 7.6 inches
• IW-8 cutout: 13.7 by 9.0 inches
• LCR cutout: 14.4 by 7.6 inches
• In-ceiling mounting depth with enclosure: 5.9 to 6.6 inches, depending on model
• In-wall mounting depth with enclosure: 3.8 inches
• Available grille shapes: round, rectangular, and square
• Available grille profiles: thin bezel and bezel-less

Detailed Description

Episode pre-construction brackets provide a physical reference before drywall is installed. Each bracket uses a color-coded system to identify the compatible speaker size or configuration. A bracket wing connects to the main bracket and can be released by pressing and holding the release button while sliding the wing away.

In-ceiling installations may use an edge plate when the speaker is positioned against a ceiling joist. This plate helps secure the installation where a conventional wing cannot be positioned normally.

In-wall speakers require four support points. The supplied wings are cut into four separate segments with tin snips, then attached to the bracket and secured to the wall studs. Markings on the wings provide a placement guide in one-inch increments, helping the installer align the bracket accurately. Speaker cable should be secured close to the bracket so it remains accessible during final installation.

Rear enclosures are intended for Signature speakers. The speaker interconnect cover is removed before the speaker is attached to the enclosure. The enclosure is aligned with the product label, and the speaker is fastened using the supplied screws. The connector grommet must be removed before the rear enclosure is installed. After mounting, the speaker wires connect to the terminals located on top of the enclosure.

Setup and Installation

Install a pre-construction bracket

1. Choose the bracket that matches the speaker model and installation position.
2. Connect the appropriate wing to the bracket. Use the release button when the wing needs to be removed.
3. For an in-wall speaker, cut the two wings into four segments with tin snips.
4. Attach the four segments to the bracket and position them against the studs.
5. Use the one-inch placement marks to establish the desired bracket location.
6. Drive screws through the metal wings to secure the bracket firmly.
7. Leave the speaker wiring within easy reach of the bracket.

Install a Signature rear enclosure

1. Remove the speaker interconnect cover.
2. Remove the connector grommet before fitting the enclosure.
3. Attach the speaker to the matching enclosure before mounting the assembly.
4. Align the enclosure using the embossed guide and the speaker product label.
5. Secure the enclosure to the speaker with the supplied screws.
6. Connect the speaker wires to the enclosure terminals.

Verify the drywall opening

Confirm the required cutout and mounting depth before cutting drywall. For Point-6 models, use the IC-8 cutout dimensions. Allow enough space for the enclosure and avoid framing, wiring, plumbing, and ductwork that could interfere with installation.

Attach a grille

Round in-ceiling grilles and rectangular in-wall grilles attach directly to the compatible speaker. Square grilles require an adapter plate.

1. Secure the adapter plate in the desired ceiling location with four #8 Phillips screws. These screws are not included.
2. Position the speaker over the adapter plate.
3. Attach the square grille to the adapter plate.

Safety

• Confirm the bracket and speaker location before cutting drywall.
• Check the installation area for studs, electrical wiring, plumbing, and HVAC obstructions.
• Use four support points for in-wall speakers to prevent inadequate mounting support.
• Secure wiring so it cannot fall out of reach before the speaker is installed.
• Use appropriate protective equipment when cutting metal bracket wings or drywall.
• Do not omit the supplied screws or substitute an unsupported mounting method for the rear enclosure.

Pros & Cons

• Pros: Color-coded brackets simplify model matching and preconstruction planning.
• Pros: Adjustable wing placement helps installers position speakers accurately before drywall.
• Pros: Rear enclosures provide a dedicated mounting and wiring solution for Signature speakers.
• Pros: Round, rectangular, thin-bezel, and bezel-less grille options support different room designs.
• Cons: Square grilles require a separate adapter plate and four #8 Phillips screws.
• Cons: In-wall bracket wings must be cut into four segments before installation.
• Cons: Incorrect bracket selection can result in an unsuitable cutout or mounting arrangement.

Warranty

Episode Accessories are covered by a limited warranty. Coverage details, including the applicable duration and terms, depend on the product warranty documentation.