Installation: Linear GD00Z-2 Garage Door Opener Remote Command Controller Instruction Manual

Overview

The GD00Z-2 Garage Door Opener Remote Command Controller is a Z-Wave-enabled device for remotely operating and monitoring a compatible sectional garage door. It connects to the garage door opener’s pushbutton terminals and works with a compatible ADT Pulse system to provide remote commands, door-status reporting, and automation options.

The system is intended for homeowners and installers who want to control a garage door through a compatible touchscreen, web portal, or mobile application while retaining the existing wall pushbutton. A wireless tilt sensor reports whether the door is open or closed, while the controller provides visible and audible warnings before movement.

Specifications

• Model: GD00Z-2
• Technology: Security-enabled Z-Wave two-way RF mesh networking
• Power input: 115 VAC power supply connected to the controller
• Opener connection: Two-wire connection to the garage door opener’s pushbutton terminals
• Tilt sensor battery: CR2032 coin-cell lithium battery
• Wireless function: Door-position reporting from the tilt sensor to the controller
• Warning indication: Flashing warning light and audible beeper for five seconds before movement
• Supported door type: Sectional or roll-up garage doors only
• Z-Wave role: The controller can repeat Z-Wave signals to help extend mesh-network communication
• Association: Supports one association group containing one controller node

Detailed Description

The GD00Z-2 system has three primary parts: the garage door controller, the wireless tilt sensor, and the power supply. The controller is the communication and switching unit. It receives commands from the connected Z-Wave system, operates the opener through its pushbutton terminals, receives position information from the tilt sensor, and controls the warning light and beeper.

The tilt sensor mounts on the top panel of the garage door. Its orientation changes as the door opens or closes, allowing it to report the door position to the controller. The sensor must remain installed with its arrow pointing upward.

The power supply provides low-voltage power to the controller. The controller should be mounted inside the garage near the opener and an electrical outlet. Its warning lamp must remain visible regardless of the door position, and the beeper must be audible.

The GD00Z-2 is a security-enabled Z-Wave product. A compatible security-enabled Z-Wave controller is required for full operation. It does not respond to basic Z-Wave command types. In a compatible ADT Pulse installation, the system can display the door status and send open or close commands through supported control interfaces.

Safety

• Install the system only on sectional or roll-up garage doors. Do not install it on one-piece doors.
• Do not install the controller on an opener manufactured before 1993 unless the opener has an operational safety-beam entrapment detection system.
• Mount the controller inside the garage, in sight of the door, so the warning light and audible warning can be observed before the door moves.
• Never walk, stand, or allow anyone else to cross the path of a moving garage door.
• Disconnect power from the garage door opener before mounting or wiring the controller.
• Keep controller wires away from all moving parts of the garage door and opener.
• Do not disconnect wires already connected to the opener’s pushbutton wall console terminals.
• Changes or modifications not expressly approved by the responsible party may void operating authority.
• Keep the CR2032 battery away from small children. If swallowed, seek medical attention immediately.
• Do not recharge the CR2032 battery. Dispose of used batteries according to local recycling and waste-handling requirements.

Package Contents

• GD00Z-2 garage door controller
• Wireless tilt sensor
• Power supply
• Controller connection wires
• Controller mounting screws and anchors
• Adjustable controller mounting bracket and related hardware
• Power-supply retaining bracket and screw
• Tilt-sensor mounting tape, mounting plate, screws, and related hardware

Setup and Installation

Prepare the Installation

Confirm that the garage door is a sectional or roll-up type and that the opener has a functioning safety-beam system. Choose a controller location near the opener and a continuously powered outlet. The location must keep the warning lamp visible and the controller clear of moving door components.

Before working on the opener wiring, unplug the garage door opener. Keep the controller’s power supply disconnected until the physical installation is complete.

Install the Tilt Sensor

1. Remove the battery-protection pull strip from the tilt sensor to activate it.
2. If screw mounting is required, open the sensor case by turning a small screwdriver in the case slot.
3. Attach the mounting plate to the top panel of the garage door using the supplied double-sided tape or screws.
4. When using screws, drill two 1/16-inch pilot holes before fastening the mounting plate.
5. Snap the sensor onto the mounting plate.
6. Verify that the arrow on the side of the sensor points upward.

Mount the Controller

The controller can be mounted directly or installed with the adjustable bracket. For direct mounting, use the supplied anchors and screws. If anchors are used, drill 3/16-inch holes as needed.

For bracket mounting, snap the adjustable bracket into the mounting indent on the side or end of the controller and secure it with the short screw. Attach the bracket to suitable opener hardware or another secure structure using the supplied bolts and nuts. Make sure the controller does not interfere with the door, opener, rail, or other moving components.

Wire the Controller to the Opener

1. Connect the two controller wires to the two pushbutton terminals on the garage door opener.
2. Terminal labels may vary by opener and can include PWC, WC, PB, or Pushbutton. Some openers identify the terminals by wire colors.
3. Either controller wire may be connected to either pushbutton terminal.
4. Leave the existing wall-console wiring connected.
5. Route the wires so they remain clear of all moving parts.

Connect Power

1. Insert the power-supply cord into the power input jack on the GD00Z-2.
2. Plug the power supply into a 115 VAC outlet.
3. Use the retaining bracket to secure the power supply if appropriate.
4. Make sure the outlet remains powered continuously and is not controlled by a wall switch.
5. Restore power to the garage door opener after the installation is complete.

Enrollment and Z-Wave Setup

The controller must be enrolled with the compatible ADT Pulse system before remote operation is available. Bring the controller close to the gateway during enrollment and apply power to the controller.

Factory Reset Before Enrollment

Before enrolling the controller in a Z-Wave network, or after removing it from another network, reset it to its factory state. Press the controller’s Include button five times. A short beep followed by a longer beep indicates that the reset was completed.

Add the Garage Door Controller

1. Open the ADT Pulse control interface and sign in.
2. Open the system-management area and select the option for managing devices.
3. Choose the category for lights, thermostats, and other devices.
4. Select the garage door remote controller from the device list.
5. Start the device-discovery process.
6. Press and hold the GD00Z-2 Include button for approximately one second.
7. Wait while the system searches for the controller. Discovery may take one or two minutes.
8. When the controller is found, assign a device name.
9. Complete the enrollment process.

Reset or Exclude the Controller

If enrollment fails, use the system’s device-management tools to reset the controller from the existing Z-Wave site. Select the device-reset function, then press and release the controller’s Include button once. After the device is reset, cancel the assistant and try the enrollment process again.

Delete the Controller

1. Open the system-management area.
2. Select the garage door controller from the device list.
3. Open the device page and choose Delete.
4. Confirm the deletion.

A controller referenced by an automation, alert, or schedule may need to be removed from those functions before the device can be deleted.

Operation

Synchronize the Door Status

1. Restore power to the garage door opener.
2. Use the opener’s wall pushbutton to open and close the door once.
3. Use the compatible ADT Pulse interface to issue a garage door command.
4. Confirm that the GD00Z-2 warning light flashes and the beeper sounds for five seconds.
5. Remain clear of the door while it moves.
6. Confirm that the control interface displays the correct open or closed status after the cycle finishes.

Warning and Movement Behavior

Before a remote command activates the opener, the controller flashes its warning light and sounds its beeper for five seconds. Treat this warning as an immediate indication that the door is about to move.

After the controller initiates movement, it does not accept another remote command for 30 seconds. This delay helps prevent repeated commands from causing unwanted door movement.

If the door does not fully open or close, the controller permits one additional remote attempt. If the second attempt also fails, remote operation enters a lockout condition. Press the local wall pushbutton to restore controller operation.

Battery Replacement

The connected system reports when the tilt-sensor battery is low. Replace it with a fresh CR2032 coin cell.

1. Use a small screwdriver in the sensor case slot to open the tilt sensor.
2. Remove the depleted battery.
3. Insert the new CR2032 battery with the positive side facing upward.
4. Close the sensor case.
5. Snap the sensor back onto its mounting plate.
6. Confirm that the sensor’s arrow points upward.

Troubleshooting

The Controller Does Not Flash or Beep

Likely cause: The controller is not receiving power.

• Check that the power supply is firmly connected to a live 115 VAC outlet.
• Confirm that the power-supply cord is fully inserted into the controller’s power input jack.
• Verify that the outlet is not controlled by a switch.

The Controller Flashes and Beeps, but the Door Does Not Move

Possible causes: An obstruction may be blocking the door, or the controller wires may be connected incorrectly.

• Inspect the door path and remove any obstruction only when it is safe to do so.
• Check that the controller wires are connected to the opener’s pushbutton terminals.
• Trace the wires from the existing wall pushbutton to identify the correct opener terminals.
• Make sure the controller wires are clear of moving components.

The Door Moves, but the Status Does Not Update

Likely cause: The controller is not receiving the tilt sensor’s signal.

• Verify that the tilt sensor is secured to the top door panel.
• Confirm that the arrow on the sensor points upward.
• Make sure the battery-protection strip was removed during installation.
• Replace the CR2032 battery if the system reports a low battery or the sensor does not respond.

Remote Commands Are Not Accepted

• Wait until the 30-second command delay has expired.
• If the controller has entered lockout after two incomplete movements, operate the door using the local wall pushbutton.
• Confirm that the controller remains enrolled with the Z-Wave system.
• Check that the controller has continuous power and that the warning indicator is visible.

Pros and Cons

Pros

• Provides remote garage door operation through a compatible Z-Wave control system.
• Reports door position using a dedicated wireless tilt sensor.
• Uses a five-second flashing and audible warning before movement.
• Can act as a Z-Wave repeater within the mesh network.
• Works alongside the existing garage door wall pushbutton.

Cons

• Designed for sectional or roll-up doors, not one-piece doors.
• Requires a compatible security-enabled Z-Wave controller for full functionality.
• Requires wiring to the garage door opener’s pushbutton terminals.
• Remote operation is temporarily delayed after movement and can enter lockout if repeated attempts fail.
• The tilt sensor requires periodic CR2032 battery replacement.