Installation: Modern Forms W137 LED Outdoor WS-W13718 Instruction Manual

Overview

The W137 LED Outdoor WS-W13718 is a modern hardwired wall light designed for residential, hospitality, and office exteriors. Its integrated LED lighting provides architectural illumination from a compact aluminum fixture, making it suitable for wet-location outdoor installations when installed correctly.

This guide explains the fixture components, electrical safety requirements, mounting procedure, wire connections, sealing method, and practical installation considerations.

Specifications

• Model: W137 LED Outdoor WS-W13718
• Fixture type: Integrated LED outdoor wall light
• Power: 11 watts total
• Light output: Approximately 275 to 300 delivered lumens
• Color temperature: 3000K
• Color rendering: CRI 90
• Voltage: Universal driver, suitable for 120–240–277V installations when supported by the electrical system
• Dimming: Compatible with electronic low-voltage dimming systems
• Dimensions: Approximately 18 inches high, 5 inches wide, and 4 inches deep
• Location rating: Wet-location rated
• Construction: Aluminum fixture body with integrated LED modules
• Installation type: Hardwired wall installation

Detailed Description

The fixture is secured to a wall-mounted back plate attached to an existing junction box. The back plate includes keyhole mounting openings and a marked grounding point. A pair of integrated LED light sources provides downward and wall-washing illumination from the rectangular housing.

The installation hardware includes wire connectors, junction-box screws, mounting screws, gaskets, wood screws, and plastic wall anchors. The gaskets sit with the mounting screws to help maintain a secure fit between the fixture and mounting plate.

When installed outdoors, the joint between the rear plate and the wall must be sealed with clear indoor/outdoor silicone caulking. The seal should remain open at the bottom so trapped moisture can drain rather than collect behind the fixture.

Safety

• Turn off power at the main circuit breaker or fuse box before beginning installation. Switching off only the wall control is not sufficient.
• Read the complete installation procedure before handling or wiring the fixture.
• Installation should be performed by a qualified electrician in accordance with the National Electrical Code and applicable local regulations.
• Use every supplied part as instructed. Do not substitute, omit, or install worn or damaged hardware.
• Handle the light by its base or housing. Do not press on the LED modules.
• Confirm that the circuit remains de-energized before touching existing wiring.
• Keep small screws, anchors, connectors, and gaskets together during unpacking so no installation hardware is lost.

Included Hardware

• Three wire connectors plus one spare
• Two junction-box screws plus one spare
• Two mounting screws plus one spare
• Two graphite or black gaskets plus one spare, depending on finish
• Two wood screws plus one spare
• Two plastic anchors plus one spare
• Fixture mounting plate and attached back plate

Setup and Installation

Prepare the Work Area

1. Switch off the circuit breaker supplying the existing wall light and verify that power is off.
2. Remove the existing fixture and its crossbar or mounting bracket.
3. Unpack the W137 LED Outdoor WS-W13718 on a clean, open surface and identify all hardware before starting.

Install the Mounting Plate

1. Remove the two mounting screws and gaskets from the fixture.
2. Hold the mounting plate against the wall and mark the keyhole locations.
3. For masonry or other suitable wall surfaces, drill at the marked points and insert the supplied plastic anchors.
4. Attach the mounting plate to the junction box with the junction-box screws.
5. Secure the plate to the wall with the wood screws and anchors where required.
6. Position the side marked “GND” toward the outside of the installation.

Connect the Wires

1. Match the fixture conductors with the corresponding house wires.
2. Connect the fixture black or smooth wire to the house black hot wire.
3. Connect the fixture white or ribbed wire to the house white neutral wire.
4. Connect the fixture bare ground wire to the green or bare copper grounding conductor in the junction box.
5. If the junction box has no grounding conductor, attach the fixture ground directly to the mounting plate using the supplied green screw.
6. Secure every connection with a supplied wire connector and gently tuck the connected wires into the junction box.

Attach and Seal the Fixture

1. Align the fixture with the mounting plate.
2. Install the mounting screws with their gaskets and tighten them evenly.
3. Apply clear outdoor silicone caulk around the exterior edge where the fixture back plate meets the wall.
4. Leave a small opening at the bottom of the sealed edge to provide a drainage path for moisture.
5. Restore power at the circuit breaker and operate the wall switch or compatible dimmer to test the light.

Operation

The W137 LED Outdoor WS-W13718 uses integrated LED modules, so no replaceable bulb installation is required. The fixture is controlled through the connected wall switch and may be dimmed when paired with a compatible electronic low-voltage dimmer and correctly configured electrical circuit.

After installation, confirm that both light areas illuminate evenly and that the fixture remains firmly seated against the wall. If the light does not operate, switch the circuit off again before inspecting connections.

Pros and Cons

• Pros: Integrated energy-efficient LED lighting, high color rendering, wet-location suitability, universal-driver voltage range, dimming support, and a sealed architectural wall-light design.
• Pros: The supplied anchors, screws, gaskets, wire connectors, and mounting plate support a complete wall installation.
• Cons: Installation requires permanent electrical wiring and should not be treated as a plug-in light.
• Cons: Correct grounding, outdoor sealing, and compatible dimmer selection are necessary for safe and reliable operation.