Speaka Professional TFT & LCD-Wall Bracket Teleskop SP-6444400 User Manual

Content

SpeaKa Professional TFT & LCD Wall Bracket Teleskop SP-6444400 Manual

Introduction

The Speaka professional TFT & LCD-Wall Bracket Teleskop SP-6444400 is a compact, adjustable wall mount designed for compatible monitors and small displays measuring approximately 13 to 30 inches. Its telescopic construction helps position a screen closer to the wall when space is limited, while the articulated arm allows the display to be extended and adjusted for a more comfortable viewing position.

This monitor wall bracket supports VESA mounting patterns of 75 × 75 mm and 100 × 100 mm and has a maximum load capacity of 15 kg. Its two pivot points provide practical movement for home offices, classrooms, reception desks, workshops, control stations, and compact entertainment areas. The screen can be angled and moved from side to side, helping reduce glare and improve visibility from different seating positions.

The SP-6444400 suits users who need a flexible LCD monitor wall mount without using a desk stand. It is particularly useful where desk space is restricted or where the display must be moved temporarily out of the way. Before installation, confirm the monitor’s VESA pattern, weight, screen size, and wall construction. The bracket is intended for compatible displays rather than oversized televisions or monitors outside its stated load and mounting limits.

SpeaKa SP-6444400 Specifications and Features

Product type: Single-monitor telescopic wall bracket for TFT and LCD displays.
Compatible display size: Approximately 13 to 30 inches, or 33.0 to 76.2 cm.
Maximum load: 15 kg, including the display and any attached accessories.
VESA compatibility: 75 × 75 mm and 100 × 100 mm mounting patterns.
Movement: Tilting and swivelling adjustment for improved viewing alignment.
Horizontal swivel: Up to 90 degrees to the left and 90 degrees to the right, depending on installation position and screen dimensions.
Wall distance: Approximately 8.1 cm when retracted and up to 39 cm when extended.
Bracket width: Approximately 195 mm.
Bracket height: Approximately 160 mm.
Colour: Black.
Typical contents: Wall plate, monitor mounting section, screws, washers, spacers, wall plugs, safety hardware, and installation instructions.

Actual movement can vary according to the display width, wall position, cable routing, and the location of the mounting holes. Do not exceed the stated load limit.

How to Install the SP-6444400 Monitor Wall Mount

Check that the display weighs no more than 15 kg and uses a 75 × 75 mm or 100 × 100 mm VESA pattern.
Inspect the wall and select solid masonry or a suitable structural fixing point. Do not rely on plasterboard alone unless an appropriate reinforced fixing system is used.
Use the wall plate as a template. Mark the fixing holes and verify that the screen will have sufficient clearance for cables and movement.
Drill holes suitable for the supplied wall plugs or the selected wall anchors. Insert the anchors fully and secure the wall plate with the fixing screws.
Attach the monitor mounting section to the display using the correct screw length. Use supplied spacers where the rear panel is recessed.
Hang or connect the display section to the wall bracket, then install and tighten the safety screw or locking hardware.
Connect the display cables while leaving enough slack for swivelling and telescopic movement.
Adjust the tilt and swivel tension gradually. Confirm that the monitor remains stable before releasing it.

Safety warning: Use two people when handling larger displays. Never drill into concealed electrical cables or plumbing. Recheck every fixing after installation and periodically during use.

SP-6444400 Troubleshooting Guide

Monitor moves or does not remain level

Check that all pivot and mounting fasteners are correctly tightened. Ensure the wall plate is level and that the display is centred on the mounting interface. Avoid forcing the arm beyond its normal range.

The screen will not attach to the bracket

Verify that the display uses either a 75 × 75 mm or 100 × 100 mm VESA pattern. Check that the screw diameter and length match the monitor manufacturer’s requirements. If the rear panel is recessed, install the correct spacers.

The bracket feels loose at the wall

Stop using the mount and inspect the wall anchors, screws, and wall material. Replace unsuitable fixings with anchors rated for the wall type and the combined weight of the bracket and display.

Cables become tight during movement

Switch off and unplug the display before rearranging cables. Leave a controlled service loop and confirm that cables do not catch on the arm or wall plate.

Noise or stiffness during adjustment

Check for overtightened joints, uneven loading, or objects obstructing the arm. Do not apply excessive force or unapproved lubricant.

No product-specific error-code system is normally associated with this mechanical wall bracket. For missing parts, suspected structural damage, or installation questions, consult the supplied instructions and contact the retailer or SpeaKa product support using the contact details provided with the purchase documentation.

Pros and Cons of the SpeaKa Professional SP-6444400

Advantages

Space-saving design: Moves a compatible monitor away from the desk, leaving more room for keyboards, documents, and equipment.
Flexible positioning: Swivel and tilt adjustment helps users align the screen for seated or standing work.
Telescopic reach: The arm can retract close to the wall or extend for easier viewing from another position.
Useful load capacity: The 15 kg limit accommodates many conventional office and industrial monitors within the supported size range.
Common VESA patterns: The 75 × 75 mm and 100 × 100 mm standards cover many compact displays.

Limitations

Limited compatibility: Displays using larger VESA patterns, unusual mounting systems, or weights above 15 kg are unsuitable.
Fixed height: Unlike a height-adjustable monitor arm, the mounting height must be chosen during installation.
Wall-dependent installation: Performance depends on suitable anchors and a structurally sound wall.
Reduced movement with larger screens: A wide monitor may restrict the practical swivel range even when the arm can rotate.

The SP-6444400 is best for users who need a sturdy, adjustable wall-mounted monitor solution in a compact workspace. A desk-mounted gas-spring arm or a heavy-duty television bracket may be more suitable for larger screens, frequent height changes, or unconventional VESA layouts.

PDF

Faqs

How do I set up the speaka professional TFT & LCD-Wall Bracket Teleskop SP-6444400 for the first time?

Confirm that your monitor uses a VESA mounting pattern of 75 x 75 mm or 100 x 100 mm and weighs no more than 15 kg. Choose a solid wall area, locate suitable fixing points, and use wall plugs appropriate for the wall material. Attach the wall plate securely, fit the monitor using the correct screws and spacers, then tighten all hardware evenly. Check that the display is safely supported before adjusting the arm.

Which monitors are compatible with the speaka professional TFT & LCD-Wall Bracket Teleskop SP-6444400?

The speaka professional TFT & LCD-Wall Bracket Teleskop SP-6444400 is intended for TFT and LCD displays measuring approximately 13 to 30 inches. Compatibility depends primarily on the monitor’s VESA hole spacing, which must be 75 x 75 mm or 100 x 100 mm, and its weight, which must remain within the bracket’s 15 kg maximum load. Always check the monitor manual for its mounting pattern and weight before installation.

How can I adjust the viewing position on the speaka professional TFT & LCD-Wall Bracket Teleskop SP-6444400?

Use the bracket’s telescopic arm to change the viewing distance, then gently swivel the monitor toward the desired position. The mount supports left-right adjustment through its articulated joints and can tilt vertically for a more comfortable viewing angle. Hold the display with both hands while adjusting it, and avoid forcing the hinges. After positioning the screen, confirm that the adjustment points remain secure and that cables are not being stretched.

What should I do if the monitor on the speaka professional TFT & LCD-Wall Bracket Teleskop SP-6444400 tilts or moves by itself?

First, remove the monitor’s weight from the arm if possible and inspect every screw, hinge, and wall fixing. Tighten loose hardware gradually without overtightening, because damaged threads can reduce stability. Check that the wall plate is flush and firmly attached to a suitable structural surface. If movement continues, reduce the arm extension, verify that the monitor does not exceed the load limit, and stop using the mount if any component is bent or cracked.

Can I install the speaka professional TFT & LCD-Wall Bracket Teleskop SP-6444400 on any wall?

The bracket should be installed only on a wall capable of supporting the combined weight of the mount and monitor. Solid masonry and suitable timber structures may be appropriate when the correct fixings are used, while plasterboard or hollow walls require properly rated anchors or a reinforced mounting point. Do not rely on decorative panels or weak surface materials alone. If the wall construction is uncertain, ask a qualified installer to verify the fixing method.

How do I prevent cables from restricting the speaka professional TFT & LCD-Wall Bracket Teleskop SP-6444400?

Leave enough slack in power, video, and USB cables for the full swivel and telescopic range. Route cables along the arm without pulling them tightly across hinges or sharp edges, and secure them with loose cable ties or clips. Test the monitor at its nearest and farthest positions before finalizing the cable route. Avoid placing cable bundles between moving joints, because they can limit adjustment, damage connectors, or gradually pull the monitor out of position.

How can I reduce screen vibration when using the speaka professional TFT & LCD-Wall Bracket Teleskop SP-6444400?

Vibration is often increased when the telescopic arm is fully extended. Push the monitor closer to the wall whenever possible and keep the display centered over the wall plate. Confirm that the wall fixings are tight and installed into a strong support surface. Check that the VESA screws are correctly sized and evenly tightened. Avoid leaning on the monitor or attaching accessories that add weight beyond the bracket’s permitted load.

How should I maintain the speaka professional TFT & LCD-Wall Bracket Teleskop SP-6444400?

Inspect the wall plate, arm joints, VESA screws, and wall fixings periodically, especially after repositioning the display. Tighten loose fasteners carefully and look for cracks, bending, corrosion, or unusual movement. Dust the bracket with a soft, dry cloth; do not spray liquid directly onto metal joints or the monitor. Keep the adjustment mechanisms free from cables and debris, and replace the mount if structural damage or persistent looseness appears.