Introduction

The IFB Appliances Eva Aqua SX 6KG 800RPM is a fully automatic front-load washing machine designed to make laundry tasks effortless and efficient. With a capacity of 6 kg, it is ideal for small to medium-sized households, offering a variety of wash programs to cater to different fabric types and soil levels. Its 800 RPM spin speed ensures effective drying, while features like Aqua Energie technology enhance water quality. Priced at approximately $300, it combines performance and convenience for everyday use.

Specifications

Model: Eva Aqua VX/SX 6 Kg 800RPM
Power supply: 220-240 V Single Phase 50 Hz
Dimension: 50.6cm (D) x 59.8cm (W) x 87.5cm (H)
Net weight: 64 kg
Capacity: 6 kg of dry cotton
Wash care programs: 8
Selector buttons: Wash Mode, Rapid Wash Start/Pause, Power
Selector knob: Program Selector
Spin speed: 800RPM
Program duration: 151 Minutes maximum, 31 Minutes minimum
Water consumption: 45 Litres
Water pressure: 0.3 Bar-10 Bar (30 KPa-1 000 KPa)
Power consumption max: 21 50 W
Drain pump rating: 30 W
Heater rating: 2000 W
Drum: Stainless steel

Product Overview

IFB Appliances Eva Aqua SX 6KG 800RPM Control Panel

control_panel_ifb_appliances_eva_aqua_sx_6kg_800rpm.png

Safety guidelines for installation

Keep the packaging material. It may come in handy when shifting residence.
- Old hoses must not be reused. Always use the new hoses delivered with the machine. Before cleaning the machine, ensure that you disconnect the main electricity supply and take the plug out of the socket.
- Not removing all the packaging and transit bolts before using the appliance may lead to serious damage. Please do not operate the machine until the transit bolts have been removed.
All washing machine installation work must be carried out only by authorised IFB Service Personnel.
Pre-installation work such as plumbing and electrical connections must be carried out by a qualified fitter, electrician or technician.
Do not operate the appliance where inflammable substances such as oil, benzene or highly inflammable gas are present. Such materials may cause fire or explosion. Never use combustible detergents.
Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point O and above SO C.
Install the machine in a room with adequate ventilation. Avoid a room with no windows. The back of the machine should be at least 4 inches (1 00 mm) away from the wall.
The machine is provided with ventilating openings on the base. Always put the machine on the floor after removing the carpet.
Do not install the machine in a damp area or bathroom with exposure to a direct shower.
Protect the machine from direct sunlight and rainfall.
Do not place the machine on a slanting, uneven or unstable surface.
A concrete floor is the most suitable installation surface for a washing machine, being far less prone to vibration during the spin cycle than wooden floorboards.
The washing machine is not suitable for connection to a hot water supply.
The machine is designed to operate with water flow pressure between 0.3 Bar-10 Bar. Lower water pressure can lead to machine malfunction.

Read all instructions and explanations for installation carefully before use. Follow the instructions carefully. Keep the operating instructions handy for later use.

Safety Information

Any damage, which may be caused by cockroaches or other vermin, will not be covered by the appliance guarantee.

Do not install and use a damaged machine. Before connecting the machine, ensure that the connection data on the data plate (fusing, voltage and frequency) match the main electricity supply. If in any doubt, consult IFB Care.
Do not wash or dry articles that have been cleaned, washed, soaked in or dabbed with combustible or explosive substances (such as oil, paint, gasoline, degreasers, dry cleaning solvents, kerosene etc). This may result in fire or explosions.
Before using the machine for the first time, check that the transit bolt at the rear of the machine has been removed (refer topic Safety Guidelines for installation).
Turn OFF the stopcock if the machine is to be left for any length of time (eg holidays) especially if there is no floor drain (gully) in the immediate vicinity.
This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instructions concerning the use of the appliance in a safe way and understand the hazards involved.
Children should not play with the appliance.
Cleaning and user maintenance should not be performed by children without supervision.

Caution

The electrical safety of this appliance can only be guaranteed when continuity is complete between the machine and an effective earthing system, which complies with local and national regulations. It is most important that a qualified electrician regularly tests this basic safety requirement. The manufacturer cannot be held responsible for the consequences of an inadequate earthing system.
For safety reasons do not operate this appliance on an extension cable. Extension leads do not guarantee the required safety of the appliance. There is danger of overheating.
The machine is built in accordance with current safety requirements.
Unauthorised repairs could result in unforeseen dangers for the user, for which the manufacturer cannot accept responsibility. Only authorised IFB personnel should undertake repairs.
The machine is only completely isolated from the electricity supply when it is switched OFF at the wall socket and the plug is taken out, or it is switched OFF from the main source, or the main fuse is taken out or the MCB switched OFF. This machine must only be connected to the onsite water supply using a new hose kit. Old hoses must not be reused. Only genuine IFB original spare parts must replace faulty components. Only when these parts are fitted can the safety standards of the machine be guaranteed.
If the connection cable is faulty it must be replaced only by an IFB approved service technician to protect the user from danger.
A washer and dryer should never be stacked without using the proper stacking kit. Doing so is extremely dangerous, as the dryer may vibrate off the washing machine during use.

Warnings

Do not pull the cord to disconnect the plug. Hold the plug itself. Do not insert or remove the plug with damp hands.
Do not drag or move the washing machine if it contains the wash load or when in operation.
Do not spill water over the machine. In case of spillage, wipe dry. Avoid the machine coming in contact with floor cleaning chemicals.
Do not wash or spray water over the switch or control panel.
Do not wash shoes or utensils in the machine.
Use detergent recommended for washing machines.
Keep your machine dry to avoid corrosion/rusting. Take special care to wipe the machine after cleaning coin trap.
Check label on garments for determining conditions under which fabrics are to be washed.
The machine is tested with water during assembly for performance checking. Condensed droplets of water may remain inside the drum. It is advisable to run the machine without a wash load in Cotton maximum temperature program with detergent for the first time after installation. Ensure that the machine is connected to a 3 pin socket with good earthing and 1 6 Amp MCB or other automatic short circuit protection devices.
Textiles that have been pre-treated in solvent-based cleaning agents must be thoroughly rinsed in clean water before being washed in the machine.
Never use solvent-based cleaning agents in this machine, as this may result in damage to component parts and create toxic fumes. Such detergents also pose a threat of fire and explosion hazards.
Only use dyes specified by the manufacturer as suitable for use in a domestic washing machine. Always read the manufacturer's instructions carefully.
Colour run and dye removers contain sulphur compounds, which can cause damage such as corrosion. Do not use such products in this machine.
For machines with a porthole door, remember that the porthole glass will be hot when washing at very high temperatures. Do not let children touch it.
Always make sure that the drum is stationary before removing clothes. Reaching into a moving drum is extremely dangerous.

Flooding danger

While hooking the drain hose into a wash basin, check that the water drains OFF quickly to prevent the sink from overflowing. Make sure the drain hose is secure so that the force of the water flowing out of the hose does not dislodge it. Otherwise this will result in flooding.
Take care to ensure that foreign objects (eg nails, pins, coins, paper clips etc) do not find their way into the machine with the washing. These may damage components of the machine (eg suds container, drum etc), which in turn can result in damage to the washing.

Description

IFB Eva Aqua is built with durability and performance in mind. The front-loading design ensures better washing and rinsing results compared to top-loading models. The 800 RPM motor provides high-speed spinning, which helps in reducing drying time significantly. The multiple wash programs allow users to choose the best cycle based on the type of clothes being washed.

Getting Started With Your Machine

Installing your machine & safety guidelines

Select the right spot

Unpack and place the new washing machine in proximity to both water and electrical connections. Ensure that the floor is properly levelled.

Removing the transit bolts

Use a spanner to remove the transit bolts.
Insert plastic caps provided.
Keep the transit bolts carefully as they will be required in case you need to shift the machine again.
Please do not operate the machine until the transit bolts have been removed.

Leveling

Level the machine by using the adjustable screws provided at the bottom for levelling.
Make sure that the machine rests on all four feet on a level surface.

Connection to the water supply

The water inlet of the machine has a collar with parallel internal threads.
The water supply point with an external thread/parallel thread should be available within 1 metre of the machine location.
Do not stretch the water supply hose.

Connection to the drain hose

The machine drains via a drain pump.
Direct the end of drain hose into a sink or a basin.
The drain hose should not be placed higher than 1 00 cm and not lower than 60 cm above the floor.

Electrical connection

It is mandatory to have a 16 Amp, 3 pin 220-240 V AC, 50 Hz electrical point with a 16 Amp MCB or automatic short circuit protection device within 1 metre of the machine.
Make sure your home has proper earthing and there is a firm connection between the plug and the socket. IFB recommends a separate MCB on the socket of the washing machine.
Proper earthing of the power socket is critical to reliable performance.

Get More From Your Machine

Tips for best results

Before washing

Empty all pockets.
Remove metals parts.
Close any zips and fasten hooks etc before washing.
Do not wash anything in the machine that is specified as non-machine washable on the wash care label.

While sorting

Separate polyester fabrics from cotton fabrics.
Try to have a mix of large and small clothes in each wash load.
Dark clothes should be washed separately and not with whites.

While loading

Load large items first, preferably half the total wash load.
Do not wash single items-add one or two similar items.
Place small items such as infants' socks, nylon stockings, handkerchiefs etc in a laundry bag, pillow case or something similar, as they may get caught around the door. This will also save your laundry from getting lost.

Water softening

Use water softening agents or adjust detergent dosage as recommended by the detergent manufacturer in case of hard water.

Easy tips to remove stains

Ensure you use warm water for soaking or pre washing stained laundry.
Fresh stains are easier to remove.
Knowing what kind of stain it is, how old it is, what kind of fabric it is, and whether the fabric is color fast (check the care label) always helps treat a stain better.
Always start with cold or warm water as hot water can set in stains. Washing and drying can sometimes set in stains.
When bleach is recommended, always use a fabric-safe one. Put the stained area face down on a paper towel or white cloth. Apply the stain remover to the back of the stain. This forces the stain off the fabric instead of through it.

Stain	Treatment
Chewing Gum, Adhesive Tape, Rubber, Cement	Use ice in a plastic bag to harden the gum. Scrape off what you can and then sponge with white spirits.
Blood	Rinse immediately in COLD water. If stain remains, soak in COLD water with an enzyme pre-wash.
Chocolate, Cocoa	Sponge with COLD water and soak in an enzyme pre-wash. If stain persists, rub a little detergent and rinse in COLD water.
Coffee	Blot up quickly and rinse out in COLD water. Rub in a little detergent and wash in the maximum temperature allowed for the fabric type.
Cream, Milk, Ice Cream	Rinse in COLD water and wash normally. If stain is still apparent, sponge with white spirits.
Deodorant	Rub affected areas with white vinegar and then rinse out in COLD water. Sponge with white spirits. Treat stiffened areas with an enzyme pre-wash.
Fabric Softener	Soak in a COLD enzyme pre-wash, rinse and wash normally.
Fruit	Treat as soon as possible by sponging with COLD water. Rub affected areas with bar soap and wash normally.
Grass	Sponge with white spirits, rub in an enzyme pre-wash and wash normally.
Grease, Oil	Lay the affected area face down on an absorbent cloth and work from the back. Sponge with white spirits or dry cleaning fluid. Wash normally.
Iron, Rust	Apply lemon juice and salt and place in the sun or dry cleaning fluid. Wash normally.
Collars, Cuffs, Cosmetics	Pre-treat with pre-wash stain remover or rub with bar soap. Wash in WARM water and detergent. Moisten area with lemon juice, dry in the sun and wash normally. If stain persists and fabric allows, use a bleach.
Mud	Brush off dry mud and rinse in COLD water. If stain persists, rub in a little detergent and wash normally.
Paint - Oil-Based	Scrape off any fresh paint and sponge with a non-flammable dry cleaning fluid and wash normally.
Paint - Water-Based	Treat while still wet. Rinse in WARM water and wash normally.
Scorch Marks	Dampen a cloth with hydrogen peroxide, lay it over the affected area and press with a fairly HOT iron.
Ink	Some inks may be impossible to remove and washing may even set it in. Use pre-wash stain remover, denatured alcohol or non-flammable dry cleaning fluid.
Nail Polish	May be impossible to remove in some cases. Place stain face down on paper towels. Apply nail polish remover to the back of the stain. Repeat, placing paper towels frequently. Do not use acetate fabrics.
Shoe Polish (Liquid)	Pre-treat with a paste of granular detergent and water.
Shoe Polish (Paste)	Scrape residue from fabric. Pre-treat with pre-wash stain remover or non-flammable dry cleaning fluid. Apply detergent into dampened area and wash using fabric-safe bleach.
Candle Wax, Crayon	Scrape off surface wax. Place stain face down between paper towels. Press with a WARM iron until wax is absorbed. Replace paper towels frequently. Treat remaining stain with pre-wash stain remover or non-flammable dry cleaning fluid. Hand wash to remove solvent and wash using fabric-safe bleach.

Setup Guide

To set up your IFB Eva Aqua SX 6KG 800RPM washing machine, follow these steps:

Unpack the appliance and remove all packaging materials.
Place the washing machine on a level surface to ensure stability.
Connect the machine to a power source and water supply lines.
Configure the drain hose according to your drainage system.
Select your desired wash cycle using the control panel.
Start the machine by pressing the 'Start' button.

Maintenance and cleaning of your washing machine

Cleaning the detergent dispenser drawer

Remove detergent residues regularly.
Pull out the detergent dispenser drawer.
Clean the detergent dispenser drawer with WARM water.
Clean the siphon. Remove the siphon from the compartment and wash it under running WARM water.
Detergent residues can build up in the water jets on top of the detergent dispenser drawer housing.
Before fixing the detergent dispenser drawer use a bottle brush to clean them out.

Cleaning the water hose mesh filter

Turn OFF taps. Disconnect power supply to the machine. Unscrew the inlet hose from machine and the tap.
Drain water from the hose.
Remove the filter mesh from the tap end of the inlet hose and clean under running water with a brush.
Pull the sieve out of the magnetic valve with a pair of flat nosed pliers. Clean the sieve under running water with a brush. Then fit the sieve back into the valve.
Screw inlet hose back to the machine and the tap. Ensure that the sieve and filter are in place. Turn ON water tap to check if the connection is watertight.

Cleaning the filter

Filter should be cleaned frequently in order to increase the life of the drain pump.
Open the detachable bottom door by using a coin or key.
Place a shallow container near the bottom door. Pull out the drain hose and open the drain plug to drain out the water from the machine in the container.
After draining the water through the drain plug, open the filter by rotating it anti-clockwise and remove foreign objects like coins, pins or hooks, if any.
Tighten the filter and drain plug to their original positions and close the bottom door.
Do not open the filter during a program run.

Use of descalant

Use descalant periodically to increase the life of the heater and to remove scaling on the heater and drum due to hard water.
Follow the instructions of the descalant manufacturer and make sure that there is no laundry in the washing machine while using it.
Only use proprietary non-corrosive descaling agents.

Cloth weights

clothes_weight_of_drawer_ifb_appliances_eva_aqua_sx_6kg_800rpm.png

Bottoms

Lungi/Dhoti: 200 g
Skirt: 200 g
Trousers: 250 g
Jeans: 400 g

Tops

Cotton shirt: 280 g
Other shirt: 200 g
Cotton blouse: 140 g
Other blouse: 100 g
Woollen sweater: 400 g
Heavy sweater: 300 g
Light sweater: 150 g

Other Clothes

Cotton saree: 650 g
Synthetic saree: 350 g
Bath towel: 600 g
Hand towel: 250 g
Pyjama kurta: 400 g
Panties: 60 g
Cotton vest: 100 g
Underslip: 100 g
Long socks (2 pairs): 150 g
Short socks (2 pairs): 85 g
6 handkerchiefs: 85 g
12 napkins: 1.1 Kg

Sheets

Cotton (double): 1 Kg
Cotton (single): 500 g
Non-cotton (double): 650 g
Non-cotton (single): 400 g

Pillow Slips

Cotton pillow slip: 110 g
Other pillow slip: 85 g

Tablecloth

Small: 230 g
Large: 600 g
Table napkins (4): 150 g

Bedspread

Bedspread: 3 Kg

Blankets

Wool: 2 Kg
Acrylic: 1.5 Kg

IFB Eva Aqua SX 6KG 800RPM Troubleshooting

When the washing machine does not function properly, check the following points before you contact your service provider.

SYMPTOM: Poor soil removal

Probable Cause	Solution
Use of Cold Wash Program	Use Hot Wash Program
Mix of heavily soiled items with lightly soiled items	Separate heavily soiled items from lightly soiled ones.
Load size not as per capacity	Use correct load size.
Cheaper quality additives	Use good quality fabric softener and detergent.
Stains on clothes	Pre-treat stains and any soiling. (Refer to topic ‘Tips to remove stains’)

SYMPTOM: Blue stains on clothes

Probable Cause	Solution
Excessive fabric additives	Do not over-use fabric softener and do not pour liquid fabric softener directly onto fabric.
Cheaper quality additives	Use good quality detergents and fabric softeners.

SYMPTOM: Black or grey marks on clothes

Probable Cause	Solution
Less quantity detergent/hard water	Use correct amount of detergent for load size, amount of soil and water hardness.
Some clothes already with existing stains	Do not mix good clothes with stained clothes.

SYMPTOM: Yellow or brown rust stains

Probable Cause	Solution
Dirty incoming water	Before washing, run water for a few minutes to clean lines or start the program only when the inlet water is clear.
Dirty washing machine	To restore the discolored load of whites, use a rust remover for fabrics.

SYMPTOM: Residue of detergent

Probable Cause	Solution
Excessive use of detergent	Use the proper amount of detergent.
Overloading of clothes	Do not overload the washing machine.
Cold Wash Program	Use Hot Wash Program.

SYMPTOM: Error LED flashes once and repeats again after 3 secs

Probable Cause	Solution
Door not closed properly or door not locked	Open and then close the door firmly.
Door not getting unlocked (at the end of program)	Cancel the program and switch OFF the appliance, wait for 2 min and check if the door can open. Do not try to open the door forcefully. If the door cannot open or if the same error indication persists, cancel the program and switch OFF the appliance. Contact IFB Care.

SYMPTOM: Error LED flashes twice and repeats again after 3 secs

Probable Cause	Solution
Water Tap turned OFF	Turn ON the tap.
Water supply not available or low water pressure	Washing machine will start automatically on resumption of water supply or press Start/Pause button twice to start refilling.
Inlet hose clogged or filter blocked in water inlet hose	Clean the inlet hose mesh filter. (Refer to topic ‘Cleaning the water hose’)
Bent/damaged water inlet hose	Remove bend/damage.

SYMPTOM: Water not drained

Probable Cause	Solution
Filter clogged	Press the Start/Pause button to restart the drain and drain pump and then clean the filter.
Drain hose kinked or clogged	Clean and straighten the drain hose.

SYMPTOM: Error LED flashes 4 times and repeats again after 3 secs

Probable Cause	Solution
Laundry load is unbalanced	Add 1-2 similar items to help balance the load and rearrange load to allow proper spinning.

SYMPTOM: Error LED flashes 5 times and repeats again after 3 secs

Probable Cause	Solution
Input Voltage is low	Machine will start automatically after the voltage rises to a safe operating level. If this error display persists for more time/frequently, contact your electrician to locate the fault in the electrical system.
Input Voltage is high	Machine will start automatically after the voltage decreases to a safe operating level. If this error display persists for more time/frequently, contact your electrician to locate the fault in the electrical system.

SYMPTOM: Error LED flashes 7 times and repeats again after 3 secs

Probable Cause	Solution
Water temperature is above 60°C at the start of the program	Start new/Drain-Spin program once the water cools down to approximately 60°C or cancel the program and switch OFF the appliance, wait for 2 secs and restart. If the same error indication persists, cancel the program and switch OFF the appliance. Contact IFB Care.

SYMPTOM: Error LED flashes 8 times and repeats again after 3 secs

Probable Cause	Solution
Water temperature is above 90°C at the start of the program	Cancel the program and switch OFF the appliance, wait for 2 secs and restart. If the same error indication persists, turn OFF the tap, cancel the program and switch OFF the appliance. Contact IFB Care.

SYMPTOM: Poor soil removal

Probable Cause	Solution
Use of Cold Wash Program	Use Hot Wash Program
Mix of heavily soiled items with lightly soiled items	Separate heavily soiled items from lightly soiled ones.
Load size not as per capacity	Use correct load size.
Cheaper quality additives	Use good quality fabric softener and detergent.
Stains on clothes	Pre-treat stains and any soiling. (Refer to topic ‘Tips to remove stains’)

SYMPTOM: Blue stains on clothes

Probable Cause	Solution
Excessive fabric additives	Do not over-use fabric softener and do not pour liquid fabric softener directly onto fabric.
Cheaper quality additives	Use good quality detergents and fabric softeners.

SYMPTOM: Black or grey marks on clothes

Probable Cause	Solution
Less quantity detergent/hard water	Use correct amount of detergent for load size, amount of soil and water hardness.
Some clothes already with existing stains	Do not mix good clothes with stained clothes.

SYMPTOM: Yellow or brown rust stains

Probable Cause	Solution
Dirty incoming water	Before washing, run water for a few minutes to clean lines or start the program only when the inlet water is clear.
Dirty washing machine	To restore the discolored load of whites, use a rust remover for fabrics.

SYMPTOM: Residue of detergent

Probable Cause	Solution
Excessive use of detergent	Use the proper amount of detergent.
Overloading of clothes	Do not overload the washing machine.
Cold Wash Program	Use Hot Wash Program.

SYMPTOM: Error LED flashes once and repeats again after 3 secs

Probable Cause	Solution
Door not closed properly or door not locked	Open and then close the door firmly.
Door not getting unlocked (at the end of program)	Cancel the program and switch OFF the appliance, wait for 2 min and check if the door can open. Do not try to open the door forcefully. If the door cannot open or if the same error indication persists, cancel the program and switch OFF the appliance. Contact IFB Care.

SYMPTOM: Error LED flashes twice and repeats again after 3 secs

Probable Cause	Solution
Water Tap turned OFF	Turn ON the tap.
Water supply not available or low water pressure	Washing machine will start automatically on resumption of water supply or press Start/Pause button twice to start refilling.
Inlet hose clogged or filter blocked in water inlet hose	Clean the inlet hose mesh filter. (Refer to topic ‘Cleaning the water hose’)
Bent/damaged water inlet hose	Remove bend/damage.

SYMPTOM: Water not drained

Probable Cause	Solution
Filter clogged	Press the Start/Pause button to restart the drain and drain pump and then clean the filter.
Drain hose kinked or clogged	Clean and straighten the drain hose.

SYMPTOM: Error LED flashes 4 times and repeats again after 3 secs

Probable Cause	Solution
Laundry load is unbalanced	Add 1-2 similar items to help balance the load and rearrange load to allow proper spinning.

SYMPTOM: Error LED flashes 5 times and repeats again after 3 secs

Probable Cause	Solution
Input Voltage is low	Machine will start automatically after the voltage rises to a safe operating level. If this error display persists for more time/frequently, contact your electrician to locate the fault in the electrical system.
Input Voltage is high	Machine will start automatically after the voltage decreases to a safe operating level. If this error display persists for more time/frequently, contact your electrician to locate the fault in the electrical system.

SYMPTOM: Error LED flashes 7 times and repeats again after 3 secs

Probable Cause	Solution
Water temperature is above 60°C at the start of the program	Start new/Drain-Spin program once the water cools down to approximately 60°C or cancel the program and switch OFF the appliance, wait for 2 secs and restart. If the same error indication persists, cancel the program and switch OFF the appliance. Contact IFB Care.

SYMPTOM: Error LED flashes 8 times and repeats again after 3 secs

Probable Cause	Solution
Water temperature is above 90°C at the start of the program	Cancel the program and switch OFF the appliance, wait for 2 secs and restart. If the same error indication persists, turn OFF the tap, cancel the program and switch OFF the appliance. Contact IFB Care.

Pros & Cons

Pros:

High-efficiency motor for faster spinning and drying times
Multiple wash programs for versatile usage
Aquafresh technology for better oil removal
Energy and water-efficient design
Durable anti-rust drum

Cons:

Higher initial cost compared to some other models
Noisy operation during high-speed spinning cycles
Slightly complex user interface for beginners

Customer Reviews

Customers have praised the IFB Eva Aqua SX 6KG 800RPM for its efficient performance, durable build, and user-friendly interface. Many users appreciate the variety of wash cycles available, which makes it suitable for all types of fabrics. However, some users have noted that it can be noisy during high-speed cycles and may require more time to get used to its features.

Most Common Complaints:

Noise during operation.
Complexity in understanding initial setup.
Higher price point compared to other models in its category.

WARRANTY

IFB Industries Ltd (the Company) warrants to the original domestic purchaser of this washing machine (Appliance) that it is free from defects in workmanship and materials. During 48 months from the date of purchase of the new washing machine all the parts of the washing machine which prove to be defective in workmanship and/or materials shall be replaced or repaired free of charge on intimation to the Company/Company's authorised service centre nearest to the place where the appliance is installed. This warranty is subject to limitations of warranty.

Search Manuals in: 800rpm

Read More