Introduction

With its contemporary style, the Whynter Portable Air Conditioner ARC-1230WNH is sure to complement any interior. An intuitive interface and a remote control make it easy to operate from a distance. A washable pre-filter and an activated carbon filter are included with the unit to guarantee clean air circulation. The cooling mode offers efficient and rapid cooling, and the dehumidifying function aids in maintaining ideal humidity levels.

A 24-hour timer, several fan settings, and automatic restart are some of the other features included in the ARC-1230WNH. You can easily chill different parts of your house or workplace as needed because to its small size and caster wheels.

Specifications

Cooling Capacity: 12,000 BTU
Dehumidifying Capacity: Up to 76 pints per day
Air Purification: Built-in air filter
Power Consumption: 115V, 60Hz, 10.8A
Noise Level: 52 dBA (low), 56 dBA (high)
15.5 x 16 x 29.5 inches

SAFETY PRECAUTIONS

Read Safety Precautions Before Operation and Installation
To prevent death or injury to the user or other people and property damage, the following instructions must be followed. incorrect operation due to ignoring of instructions may cause death, harm or damage.

Installation must be performed according to the installation instructions. Improper installation can cause water leakage, electrical shock, or fire.
Use only the included accessories and parts, and specified tools for the installation. Using non-standard parts can cause water leakage, electrical shock, fire, and injury or property damage. Make sure that the outlet you are using is grounded and has the appropriate voltage.
The power cord is equipped with a three-prong grounding plug to protect against shock.
Voltage information can be found on the nameplate of the unit.
Your unit must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker (the fuse or circuit breaker needed is determined by the maxi mum current of the unit. The maximum current is indicated on the nameplate located on unit), have a qualified electrician install the proper receptacle.
Install the unit on a flat, sturdy surface. Failure to do so could result in damage or excessive noise and vibration.
The unit must be kept free from obstruction to ensure proper function and to mitigate safety hazards.
Do not modify the length of the power cord or use an extension cord to power the unit.
Do not share a single outlet with other electrical appliances. Improper power supply can cause fire or electrical shock.
Do not install your air conditioner in a wet room such as a bathroom or laundry room. Too much exposure to water can cause electrical components to short circuit.
Ensure there is a minimum of 36″ clearance around the unit and is clear from any combustible items such as propane, fire extinguishers, fuel, etc.
The exhaust hose should always be used and should never be covered or blocked which can become a fire hazard. • The unit has wheels to facilitate moving. Make sure not to use the wheels on thick carpet or to roll over objects, as these could cause tipping.
Do not operate a unit that it has been dropped or damaged.
Do not place the portable air conditioner close to any other heat generating appliances
Do not touch the unit with wet or damp hands or when barefoot.
If the air conditioner is knocked over during use, turn off the unit and unplug it from the main power supply immediately. Visu ally inspect the unit to ensure there is no damage. If you suspect the unit has been damaged, contact a technician or customer service for assistance.
In a thunderstorm, the power must be cut off to avoid damage to the machine due to lightning.
Your air conditioner should be used in such a way that it is protected from moisture. e.g. condensation, splashed water, etc. Do not place or store your air conditioner where it can fall or be pulled into water or any other liquid. unplug immediately if it occurs.
All wiring must be performed strictly in accordance with the wiring diagram located inside of the unit.
The unit’s circuit board (PCB) is designed with a fuse to provide overcurrent protection. The specifications of the fuse are printed on the circuit board, such as: T 3.15A/250V, etc.
When the water drainage function is not in use, keep the upper and the lower drain plug firmly plugged into to the unit to pre vent choking.

CAUTION

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Children must be supervised around the unit at all times.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Prior to cleaning or other maintenance, the appliance must be disconnected from the supply mains.
Do not remove any fixed covers. Never use this appliance if it is not working properly, or if it has been dropped or damaged.

CAUTION

Do not remove any fixed covers. Never use this appliance if it is not working properly, or if it has been dropped or damaged.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
Do not operate unit with a damaged cord, plug, power fuse or circuit breaker. Return to an authorized service facility for examination and/or repair.
To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
The appliance shall be installed in accordance with national wiring regulations.
Contact the manufacturer or authorized service technician for repair or maintenance information of this unit.
Contact the manufacturer or authorized installer for installation questions of this unit.
Do not cover or obstruct the inlet or outlet grilles.
Do not use this product for functions other than those described in this instruction manual.
Before cleaning, turn off the power and unplug the unit.
Disconnect the power if strange sounds, smell, or smoke comes from it and contact the
manufacturer or authorized service technician for assistance.
Do not press the buttons on the control panel with anything other than your fingers.
Do not remove any fixed covers. Contact Wynter Customer Support if this unit if it is not working properly, or if it has been dropped or damaged.
Do not operate or stop the unit by inserting or pulling out the power cord plug.
Do not use hazardous chemicals to clean or come into contact with the unit. Do not use the unit in the presence of inflammable substances or vapor such as alcohol, insecticides, petrol, etc. Always transport your air conditioner in a vertical position and stand on a stable, level surface during use.
Always contact Wynter Customer Support for replacement parts compatible with your unit. Hold the plug by the head of the power plug when taking it out.
Turn off the product when not in use.

WARNING

The appliance shall be stored in a room without continuously operating ignition sources (for example: open flames, an operating gas appliance or an operating electric heater).
Do not pierce or burn the unit.
Be aware that the refrigerants may not contain an odor.

SAFETY COMPLIANCE

Keep ventilation openings clear of obstruction.
The appliance shall be stored so as to prevent mechanical damage from occurring.
A warning that the appliance shall be stored in a well-ventilated area where the room size corresponds to the room area as specified for operation.
industry-recognize
Any person who is involved with working on or breaking into a refrigerant circuit should hold a current valid certificate from an industry-accredited assessment authority, which authorizes their competence to handle refrigerants safely in accordance with an industry recognized assessment specification.
Servicing shall only be performed as recommended by the equipment manufacturer.
Maintenance and repair requiring the assistance of other skilled personnel shall be carried out under the supervision of the person competent in the use of flammable refrigerants.
Please follow the instructions carefully to handle, install, clear, and service the air conditioner to avoid any damage or hazard. Flammable Refrigerant R32 is used within air conditioner. When maintaining or disposing the air conditioner, the refrigerant (R32) shall be recovered properly and shall not discharge to air directly.
No any open fire or device which may generate spark/arcing shall be around air conditioner to avoid causing ignition of the flammable refrigerant used.
Please follow the instruction carefully to store or maintain the air conditioner to prevent mechanical damage from occurring.
Flammable refrigerant R32 is used in air conditioner. Please follow the instruction carefully to avoid any hazard. For specific information on the type of gas and the amount, please to the relevant label on the unit itself.

PREPARATION

All illustrations in the manual are for explanation purpose only. Your machine may be slightly different. The actual shape shall prevail. The unit can be controlled by the unit control panel alone or with the remote controller.

Whynter ARC-1230WN Smart Portable Air Conditioners - Air panel

DESIGN NOTICE
In order to ensure the optimal performance of our products, the design specifications of the unit and remote control are subject to change without prior notice.
EXHAUST HOSE INSTALLATION
The innovative hose-in-hose design delivers more than 2x faster and stronger cooling. The hoses and adapter must be installed or removed in accordance with the usage mode. For COOL mode & HEAT mode (only for ARC-1230WNH ), the adapter and exhausts must be installed. For FAN or DRY mode, the adapter and exhaust hoses can optionally be removed.
CHOOSING THE RIGHT LOCATION

Your installation location should meet the following requirements:

Make sure that you install your unit on an even surface to minimize noise and vibration.
The unit must be installed near a grounded plug, and the Collection Tray Drain (found on the back of the unit) must be accessible.
The unit should be located at least 25cm (9.8″) from the nearest wall to ensure proper air conditioning. The horizontal louver blade should be at least 50cm (19.7″) away from obstacles.
DO NOT cover the Intakes, Outlets or Remote Signal Receptor of the unit, as this could cause damage to the unit.

AMBIENT TEMPERATURE RANGE FOR UNIT OPERATION

MODE	TEMPERATURE RANGE
Cool	62-95’F I 17-35’C
Dry	62-95’F I 17-35’C
Heat (heat pump mode)	41-86’F I 5-30’C (only for ARC-1230WNH)

INTRODUCTION TO INVERTER TECHNOLOGY
As pioneers in the air comfort space, we are introducing next generation technology currently used only in high efficiency ductless mini-split air conditioners. The Inverter technology will be featured in our NEX line of portable air conditioners. By utilizing this much more efficient technology, Whiner’s Inverter variable-speed system allows the compressor to optimize efficiency and power consumption together, while maintaining a specified output.
This allows for a much quieter operation and significantly reduced energy con sumption. The Inverter technology system potentially reduces energy usage by more than 40% while the new hose-in-hose design delivers more than double the cooling output. Below are the advantages of inverter technology; At least 40%- 50% cheaper to run as it consumes less power Quicker to achieve desired temperature

Quieter operation
No temperature fluctuations
No voltage peaks from compressor

HOSE-IN-HOSE COOLING SETUP
The innovative two-hose in one design and the sealed bottom structure ensure no heat leakage. This cooling setup extracts and exhausts air from the outdoor, so the indoor space reaches an independent and balanced cool air circulation. As a result, the entire room can be cooled down quickly and effectively.

Model	ARC-103OWN	ARC-1230WN	ARC-123OWNH
Operational Modes	Cool / Fan / Dry	Cool / Fan / Dry	Cool / Fan / Dry / Heat
Cooling Capacity	12,000 BTU I SACC 10,000 BTU	14,000 BTU I SACC 12,000 BTU	14,000 BTU I SACC 12,000 BTU
Heating Capacity	–	–	12,000 BTU
Coverage Area	500 sq. ft.	600 sq. ft.	600 sq. ft.
Fan Speed	Continuous I Auto I Low I Medium I High	Continuous I Auto I Low I Medium I High	Continuous I Auto I Low I Medium I High
Noise Level	42.5 / 49.5 / 53.5	42.5 / 49.5 / 56.5	47.2 / 52.6 / 56.8
Temperature Range	60-86°F	60-86°F	Cooling: 60-86°F I Heating: 60-86°F
Timer	Up to 24 hours	Up to 24 hours	Up to 24 hours
Refrigerant	R32	R32	R32
Power Consumption	1266W	1293W	1298W
Amps	12.	12.	12.
Power Supply	115V/60Hz	115V/60Hz	115V/60Hz
CEER I EER	12.3 I 10.0	12.3 I 10.8	12.3 I 10.8
Net Weight	72.8 lbs	75 lbs	77.2 lbs
Unit Dimensions	19.5″ W x 16.7″ D x 32.5″ H	19.5″ W x 16.7″ D x 32.5″ H	19.5″ W x 16.7″ D x 32.5″ H

WHAT SHOULD I LOOK FOR WHEN PURCHASING A PORTABLE AIR CONDITIONER?
The right air conditioner helps you cool a room efficiently. An undersized unit won’t cool adequately while one that’s too large will not remove enough humidity, leaving the air feeling damp. To find the proper air conditioner, determine the square footage of the room you want to cool by multiplying the room length by its width. You also need to know the air conditioner’s BTU {British Thermal Unit) rating, which indicates the amount of heat it can remove from a room.

Why is the cooling capacity lower on newer models than on older units?
A higher number means more cooling power for a larger room. (Be sure you are comparing only newer models to each other- older models may appear to have a higher capacity, but are actually the same). Be sure to “size up” if your portable air conditioner will be placed in a very sunny room, in a kitchen, or in a room with high ceilings. After you’ve found the right cooling capacity for your room, you can look at other features.

WHY IS THE COOLING CAPACITY LOWER ON NEWER MODELS THAN OLDER MODEL$?
Federal regulations require manufacturers to calculate cooling capacity based on a specific test procedure, which was changed just this year. Models manufactured before 2017 were tested under a different procedure and cooling capacity is measured differently than in previous models. So, while the BTUs may be lower, the actual cooling capacity of the air conditioners has not changed.

WHAT IS SACC?
SACC is the representative value of Seasonally Adjusted Cooling Capacity, in Btu/h, as determined in accordance with the DOE test procedure at title 10 Code of Federal Regulations (CFR) 430, subpart B, appendix CC and applicable sampling plans.

ACCESSORIES

Image	Accessory	Qty
	Hose-in-hose (Air intake hose & exhaust hose)	1 set
	Air outlet adapter	1 piece
	Exhaust Connector Module ABC*	1 piece each
	Window Slider A	1 piece
	Window Slider B	1 piece
	Foam Seal A (Adhesive)	2 pieces
	Zip Tie ( For ARC-1230WNH model only)	2 pieces
	Foam SealB (Adhesive)	2 pieces
	Foam Seal C (Non-Adhesive)	1 pieces
	Security Bracket	1 set
	Drain Hose Adaptor (For ARC- 1230WNH model only)	1 piece
	Power Cord Buckle (N/A for ARC- 1230WNH model)	1 piece
	Bolt	1 piece
	Remote Control	1 set
	Drain Hose Adaptor	1 piece
	Washable Filter (preinstalled)	1 piece

Description

The Whynter Portable Air Conditioner ARC-1230WNH boasts a sleek and modern design that fits well with most home or office decor. It features a user-friendly control panel with a remote control for convenient operation from across the room. The unit comes with a washable pre-filter and an activated carbon filter to ensure clean air circulation. The dehumidifying function helps maintain optimal humidity levels, while the cooling mode provides quick and efficient cooling.

The ARC-1230WNH also includes features like automatic restart, a 24-hour timer, and multiple fan speeds. Its compact size and caster wheels make it easy to move around, allowing you to cool different areas of your home or office as needed.

WINDOW KIT INSTALLATION

Whynter ARC-1230WN Smart Portable Air Conditioners - Window Slider

Adjustable Window Slider Option

Measure the window opening where the window kit will be installed.
Assemble as many sliders as necessary to fit the window. If the window opening is less than the minimum length of a single slider, use the slider that has the hole in it and cut it to the correct length. Make sure not to cut the end that has the hole as this is necessary to attach the exhaust hose adapter.
Use the window slider bolts to secure the window sliders at the correct length.

Whynter ARC-1230WN Smart Portable Air Conditioners - Hoses Connector Modules

Hoses Connector Modules (For Sliding Window)
Assemble the exhaust adapter module for sliding windows using the exhaust connector screw as shown. The window slider is eccentric so the exhaust adapter must be installed away from the wall.
Note: For vertical installation, exhaust hose connector module B can be omitted.

Rotate the exhaust hose gently backwards.
Pull out the exhaust hose away from the wall.

Whynter ARC-1230WN Smart Portable Air Conditioners -

Hose-in-hose
NOTE: To ensure proper functioning, DO NOT overextend or bend the hose. Make sure that there is 20″ of clearance around the air outlet of the exhaust hose in order for the exhaust system to work properly.
All illustrations in this manual are for explanation purposes only. Your air conditioner may be slightly different. The actual shape shall prevail.

NOTE: Once the Exhaust Hose assembly and Adjustable Window Slider are prepared, choose from one of the following two installation methods.

Hung Window or Sliding Window Installation

Cut adhesive foam seals A and B to the correct lengths and attach them to the window frame as shown.
Insert the window slider kit into the window opening and close the window the secure it in place.
Cut the non-adhesive foam seal C to match the width or height of the window and insert it between the panes of glass as shown to prevent outside air from entering the window.
If desired, install the security bracket with 2 screws as shown.
For a hung window, attach the air outlet adapter onto the exhaust hose and rotate it 90° to secure it in place. For a sliding window, attach the exhaust adapter onto the exhaust hose.
For a hung window, attach the air outlet adapter onto the window slider kit. For a sliding window, attach the exhaust adapter onto the window slider kit.

CONTROL PANEL

DISPLAY ICONS

Wireless feature (Wi-Fi enabled models only)
Illuminates to show wireless connection is activated.
The timer on/oﬀ indicator light
Press and hold on TIMER button for 3 seconds to cancel timing function.
Operation Mode Indicator Lights
Illuminates to show current mode operation.
LED Display
Shows the set temperature in °For °C and the Auto-timer settings. While on FAN modes, it shows the room temperature.
Fan Speed Indicator Lights
Illuminates to show the set fan speed.
Sleep Indicator Light
Illuminates when Sleep Mode is activated.
Filter Indicator Light?
The LED will illuminate after 250 hours of operation. This feature is a reminder to clean the Air Filter for more efficient operation.

CONTROL BUTTONS

Swing/Wireless Mode
Auto-swing
Press to start the auto swing feature. When the operation is ON, press the SWING button to stop the louver at a desired angle.
Turn on Wireless connection mode
To turn on Wireless connection mode on, press and hold the swing button for 3 seconds and the LED display will show “AP” for 3 seconds. Follow the instructions on the Wi-Fi setup manual and the latest app version available for your phone operating system.
Turn off Wireless connection mode
Once the wireless connection mode is successful, press and hold the swing and down buttons for 3 seconds and the LED display will show “OF” for 3 seconds.
Connection Successful
If the connection is successful within 8 minutes, the unit will exit wireless connection mode automatically and the wireless indicator will illuminate.
Connection Failed
If the connection has failed within 8 minutes, the unit will exit Wireless connection mode automatically.
NOTE: When you restart the wireless functions, it will take a period of time to connect to the network automatically. Always be sure your wireless connection is working properly and there is a valid internet connection for Wi-Fi functionality to work.
Timmer
Press to program timer delayed switch ON or OFF function.
Modes
Press to change modes. Controls the functions modes: AUTO, COOL, DRY, FAN, and HEAT.
*only for ARC-1230WNH

Whynter ARC-1230WN Smart Portable Air Conditioners - Control panel 1

CONTROL BUTTONS

Up and Down buttons
Adjusts set temperature 1 °F I 1 °C increments or timer hours (O – 24 hours).
NOTE: This unit is capable of displaying set temperature in Fahrenheit or Celsius. To convert from one to another, press and hold the Up and Down buttons for 3 seconds.
Fan
Press to change fan speed. Controls the 5 fan speeds and mode: Continuous, Auto, Low, Medium, and High.
NOTE: In Auto and Dry mode, the fan speed control is disabled Continuous Fan Mode. Press and hold to select continuous fan speed. The fan speed will keep on operating in a continuous speed based on the last fan speed setting.
Sleep Mode
Press to activate Sleep mode. Press SLEEP button again to stop the sleep operation.
NOTE: This feature is not available in FAN or DRY mode.
Filter
Press SLEEP button for 3 seconds to clear the clean filter light reminder.
Power
Press to turn the air conditioner on and off.

ERROR CODES

El – Room temperature sensor error
Unplug unit and restart in 5 minutes
E2 – Evaporator sensor error
Unplug unit and restart in 5 minutes
E3 – Condenser sensor error
Unplug unit and restart in 5 minutes
E4 – Display panel sensor error
Unplug unit and restart in 5 minutes
Pl – Water reservoir full
Drain water from the unit

OPERATION INSTRUCTION

BEFORE USING YOUR APPLIANCE

Remove the exterior and interior packing
Before connecting the appliance to the power source, let it stand upright for approximately 4 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation

SWITCHING ON/OFF THE AIR CONDITIONER
The appliance can be switched ON or OFF by pressing the POWER button on the control panel or the ON/OFF button on the remote control

COOLING MODE

In this mode, the air conditioner cools and dehumidifies the room. To activate this function mode, press the MODE button until the COOL indicator light comes on. When the cooling mode is set, the compressor will start in approximately 3 minutes. In cooling mode, hot air is exhausted from the outdoor exhaust port and the exhaust hose must be connected to exhaust out the hot air.

The temperature setting range of this air conditioner is from 60°F / 16°C to 86°F / 30°C. To set the temperature, press the + or – buttons. This air conditioner has a 5°F temperature cushion which if the set temperature is within 5°F of the ambient temperature, the unit runs on fan only mode. This saves energy and prolongs the life of the compressor of the air conditioner. To set the fan speed, press the FAN button.

In cooling mode, the difference in noise level between the fan speeds is not very no ticeable when the compressor is on. Try setting the unit to Fan only mode, you should be able to hear the difference between high and low fan speed settings.

DRY (DEHUMIDIFYING) ONLY MODE

In this mode, the air conditioner only dehumidifies the room, the compressor will activate intermittently depending on the ambient temperature and the fan speed is set to LOW. To activate this function mode, press the MODE button until the DRY indicator light is displayed. Please note that when switching function mode, there will be an approximately 3 minute transition time. In dehumidifying mode, the exhaust hose does not need to be vented. If the exhaust hose is vented, the room will be cooled as it dehumidifies.

To prevent cooling, remove the exhaust hose from the window kit and allow the warm air from the rear to be re-circulated into the room. If room temperature is higher than 77°F, the fan speed can be adjusted. If room temperature is lower than 77″F, the fan speed is set at low.

NOTE: When using dehumidifying mode, venting the exhaust hose to the outside is not required. If vented, the warm air is exhaust ed to the outside and cooling within the room may occur. Additionally, if the exhaust hose is not vented, the unit may require more frequent draining. Also, the air conditioner does not have a humidistat in which a specific humidity level can be set.

AUTOMATIC MODE

When you set the air conditioner in AUTO mode, it will automatically select cooling, heating*, or fan-only operation depending on what temperature you have selected and the room temperature. The air conditioner will control the room temperature automatically around the set temperature selected.

The fan speed is automatically selected and cannot be changed. To operate the unit in Auto mode when the unit is on, press the mode button until the Auto indicator light comes on *ARC-1230WNH model only.

HEAT MODE (*only for ARC-1230WNH)
This air conditioner operates on the heat-pump principle, absorbing heat from air outdoors and transferring that heat to the indoor unit. In this mode, the air conditioner heats the room. To activate this function mode, press the MODE button until the HEAT indicator display comes on. When the heating mode is set, the compressor will start in approximately 3-5 minutes.

The heating temperature setting range of this air conditioner is from 60°F -86°F / 16°C -30°C. To set the temperature, press the UP and DOWN buttons. To set the fan speed, press the FAN button.

FAN ONLY MODE
In this mode, only the fan of the air conditioner runs and circulates the air in the room. To activate this function mode, press the MODE button until the FAN indicator light comes on. In this function mode, the temperature cannot be set. Subsequently, set the desired fan speed by pressing the FAN button.

When using FAN only mode, venting the exhaust hose to the outside is optional.

TIMER (DELAYED SWITCH ON/ OFF) FUNCTION
This function mode enables a delayed switch ON or delayed switch OFF of the air conditioner. The time (hours) delay can be set, enabled and disabled.

SETTING SWITCH OFF TIMER

With the air conditioner operating in any function mode, press the TIMER button. The TIMER OFF light will come on. Then set the desired time delay OFF hours by pressing the UP and DOWN buttons. The time increments are at 0.5 hour to up to 10 hours, followed by 1 hour increment up to 24 hours.

When the delay time set has elapsed, the air conditioner switches off. To cancel the delayed switch off function, turn off the air conditioner or adjust the time set-ting to 0.0.

SETTING DELAYED SWITCH ON TIMER

With the air conditioner is off, press the TIMER button. The TIMER ON light will come on. Then set the desired time delay ON hours by pressing the UP and DOW N buttons. The time increments are at 0.5 hour to up to 10 hours, fol- lowed by 1 hour increment up to 24 hours. When the delay time set has elapsed, the air conditioner switches on.

To cancel the delayed switch on function, turn on the air conditioner or adjust the time setting to 0.0.

SENSE FUNCTION
The remote control serves as a remote thermostat allowing for the precise and comfortable temperature control. With this technology, an efficient temperature sensor is integrated in the remote control. To activate the I SENSE function, press I SENSE button on the remote control.

Once this function is activated, the remote control will send the temperature signal to the air conditioner every 3 minutes interval until you press the I SENSE button again. The air conditioner will automatically cancel the I SENSE feature if it does not receive the signal during any 7 minutes interval.

NOTE: The I SENSE feature is not available in DRY and FAN mode. Shifting the operating mode or turning off the unit will cancel the Follow Me feature automatically. The remote control needs to be within 26 feet reach of the indoor unit for the I SENSE mode to work appropriately.

SLEEP MODE

In this mode, the air conditioner gradually increases the set temperature in cooling mode or decreases the set temperature in heating mode*. It decreases the noise level and conserves energy. In cooling mode, the set temperature is increased by 2°F/ 1°C in the first 30 minutes. The temperature will then increases by another 2°F/ 1°C after an additional 30 minutes.

For models with heat mode, the set temperature is decreased by 2°F/ 1°C in the first 30 minutes. The temperature will then decreases by another 2°F/ 1°C after an additional 30 minutes. This new temperature will remain the same for 7 hours.

To activate this function mode, press the SLEEP button until the SLEEP indicator light comes on.

NOTE: This feature is not available in FAN or DRY modes.
ARC-1230WNH model only

AUTO RESTART
In the event of a power outage, the air conditioner restarts at the previously set function mode and settings when power is restored.

CONTROLLING THE AIR FLOW DIRECTION
The louvers can be controlled to Auto-Swing or in a fixed direction. To control the air flow direction by Auto-Swing, press the SWING button. To set the louvers in a fixed angle or direction, press SWING button while on Auto-Swing mode when desired angle is chosen.

CLEAN FILTER REMINDER
The FILTER light on the display will illuminate after 250 working hours as a reminder to clean the filter for a more efficient operation. After cleaning the filter, press the SLEEP button for 3 seconds to clear the clean filter reminder light.

NOISE LEVEL
Portable air conditioners may make sounds that are not familiar to you. The sounds listed below are normal. Noise reflecting off hard surfaces such as a floor or wall can make sounds seem louder than they actually are.

The compressor may make a pulsating or high-pitched sound
Water running from the evaporator to the water tank may make a splashing sound
Refrigerant flowing may make a gurgling sound
Fan sound may come from front and back air vents

COMPRESSOR LOCK OUT
This portable air conditioner is optimized to operate in an ambient temperature of 64°F – 90°F. The compressor circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This prevents over-heating of the compressor and possible circuit breaker tripping.

REMOTE CONTROL

The portable air conditioner can be switched on by the remote control. To transmit signals from the remote control to the air conditioner, point the front part of the remote handset towards the control panel on the air conditioner. Reception of the signal is confirmed by a beep. The maximum signal transmission distance is approximately 8 meters/ 26 feet.
NOTE:

Other appliances in the same room controlled by a remote control (TV, radio, stereo, etc.), may cause interferences
Electronic and fluorescent lamps may interfere with the signal transmissions between the remote control and the air conditioner
Remove the batteries if the remote control is not used for long periods

Whynter ARC-1230WN Smart Portable Air Conditioners - Remote control

1	Mode indicator	Displays the current selected mode (Auto, Cool, Dry, Heat* or Fan)
2	Wireless indicator	Displays when the remote is turned on, and disappears when it is turned off
3	Timer On indicator	Displays when TIMER ON is set
4	Timer Off indicator	Displays when TIMER OFF is set
5	Swing indicator	Displays auto-swing feature is turned, and disappears when it is turned off
6	Temperature/Timer display (h)	Displays the set temperature or timer setting when using ON/ OFF functions “h (hours)” indicator is shown when timer settings are activated
7	Remote Control indicator	Displays when the remote is turned on and disappears when it is turned off
8	Temperature Scale indicator	Displays temperature scale Fahrenheit or Celsius
9	Lock settings indicator	Indicated all the current settings are locked
10	Sleep Feature indicator	Displays when SLEEP function is activated
11	I Sense Feature indicator	Displays when I SENSE function is activated
12	Fan Speed indicator	Displays the current selected fan speed
13	Up button	Increases set temperature/time
14	Down button	Decreases set temperature/time
15	Mode button	Controls the function modes: Auto, Cool, Dry, Heat* and Fan *only for ARC-1230WNH
16	Power button	Turns the unit On and Off
17	Fan Speed button	Controls the fan speeds: Auto, High, Medium, or Low (Continuous mode cannot be set using the remote control)
18	Swing Feature button	Press to stop or start louver auto-swing feature
19	Sleep Feature button	Starts or stops louver movement and set louver angle
20	Timer ON button	Enables the Timer On
21	I Sense Feature button	Press to initiate I SENSE feature
22	Lock settings button	Press I SENSE and TIMER OFF buttons to lock current settings
23	Timer OFF button	Enables the Timer Off
24	LED Display button	Press this button to turn on and turn off the display on the indoor unit
25	Temperature Scale button	Press to change Temperature Scale (Fahrenheit I Celsius)

REPLACING THE REMOTE BATTERIES

This remote control comes with two AAA batteries. Place the batteries in the remote control before use.

Slide the back cover from the remote downward to expose the battery compartment.
Insert the batteries, ensure to match the(+) and ( ) symbols on the ends of the batteries with the symbols inside the battery compartment.
Slide the battery cover back into place.

Whynter ARC-1230WN Smart Portable Air Conditioners - Remote control 1

Notes:

The air conditioner will not respond if curtains, doors or other materials block the signal from the remote control to the unit.
Prevent any liquid from contact with the remote control. Do not expose the remote control to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air conditioner may not function properly. Use curtains to prevent the sunlight from falling on the receiver.
Do not mix old and new batteries or batteries of different types .
Do not leave the batteries in the remote control if it is not going to be used for more than two months.

Setup Guide

To set up the Whynter Portable Air Conditioner ARC-1230WNH,

Start by unpacking the unit and all included accessories such as the exhaust hose, window kit, and remote control.
Place the air conditioner on a level surface and ensure it is at least 12 inches away from any walls or obstructions.
Next, connect the exhaust hose to the back of the air conditioner and secure it to the window using the provided window kit.
Plug in the unit and turn it on using the control panel or remote control. You can select the desired mode (cooling, dehumidifying, fan) and adjust settings such as temperature and fan speed according to your preferences.

CARE AND MAINTENANCE

SAFETY PRECAUTIONS

Always unplug the unit before cleaning or servicing.
DO NOT use flammable liquids or chemicals to clean the unit.
DO NOT wash the unit under running water. Doing so causes electrical danger.
DO NOT operate the portable air conditioner if the power supply was damaged during cleaning. A damaged power cord must be replaced with a new cord. Contact Whynter Customer Support for more information.

WATER DRAINAGE

When the internal drain pan becomes full the appliance will beep 8 times and the digital display will show error code Pl. The air conditioning or dehumidifying action will stop but the fan may continue to operate. Ensure that the appliance is turned off and unplugged and that it is close to a floor drain before setting up any drain option.

Whynter ARC-1230WN Smart Portable Air Conditioners - Gravity Drain

A. Drain Plug
Remove the drain plug and allow the water to completely drain. Replace the bottom drain plug, pressing firmly to ensure a tight fit and no leaks.
B. Continuous Gravity Drain
During dry mode, install continuous drain option so that the appliance will automatically drain collected water. Remove the upper drain plug and attach the drain hose that was provided with the appliance. Place the open end of the drain hose over the receptacle that the appliance will drain into; this could be a basement floor drain, a sink or similar.
Ensure that there are no kinks or bends in the drain hose and that it goes straight down toward the floor. The continuous drain is activated by gravity only. If the hose is not positioned directly downwards, water will not drain correctly.
C. Heat pump drainage (for ARC-1230WNH only)
This unit has a condensate pump feature that can pump out (and up) water through the included drain hose for continuous water removal during HEAT Mode. Remove the heat pump drain plug from the back of the unit and install the drain hose. Place the open end of the hose to a drain area.

NOTE: The condensate pump will only engage during Heat mode and will not work in any other modes. Pump drain hose is required to be installed when using the portable air conditioner in Heat Mode.
NOTE: To reduce pump drain noise, make sure to attach the drain hose adaptor to the open end of the drain hose. To secure the adaptor in place, use the provided zip tie.

UNIT CLEANING

CLEANING

Unplug the appliance before cleaning or servicing.
Clean the cabinet with a lukewarm damp cloth and neutral detergent. Dry the cabinet with a lint-free dry cloth.
Do not use gasoline, paint thinner or other chemicals to clean the appliance.
Do not wash the appliance directly under a tap or using a hose. It may cause electrical damage.

AIR FILTER
The air filter should be cleaned every two weeks to ensure efficient performance. In households with animals, the air filter may need to be cleaned more often and the external grills may need to be wiped to prevent blocked air flow.
To access the filter:

Whynter ARC-1230WN Smart Portable Air Conditioners - UNIT CLEANING

Switch off the air conditioner.
Hold the exhaust hose, push it backward slightly and then lift it up.
Remove the filter from the unit.
Use a vacuum cleaner or tap lightly to remove loose dust and dirt.
Rinse the filter thoroughly under warm running water (no hotter than 100 °F.)
Dry thoroughly before re-inserting the filter.

LONG-TERM STORAGE

Drain all water from the appliance.
Run the appliance on Fan mode for half a day in a warm room to dry the inside of the appliance and prevent mold formation.
Turn off the appliance and unplug it, wrap the cord and bundle it with tape.
Remove the batteries from the remote control.
Clean the air filter and reinstall it.
Store the appliance in a cool, dark place. Prolonged exposure to direct sunlight or extreme heat can shorten the lifespan of the appliance.

DISPOSAL
This appliance should not be treated as regular household waste. Check for local regulatory compliance regarding the approved and safe disposal of this appliance.

TROUBLESHOOTING

PROBLEM	POSSIBLE CAUSES	SOLUTIONS
The portable air conditioner does not turn on	• Power failure / outage • The automatic switch, line fuse, or breaker has been tripped • The power supply voltage is too low • The power cord is damaged • The L.C.D.I. power plug for the unit is tripped • The internal water reservoir is full and ‘P1″ appears on display	• Restore the power supply • Flip the switch / change the fuse /turn the breaker back on. Also note that you may have too many applianc-es drawing power on one circuit, you may need to move the other applianc- es to another circuit • Move the unit onto another circuit with the correct voltage • Call for service. Only authorized personnel should replace damaged power cord or power plug • Press the Reset button on the L.C.D.I. power plug • Drain water from the air conditioner • Possible loose internal connection. • Please contact Whynter for service.
The unit turns on but the compressor does not turn on (the fan runs but the unit is not cooling)	• The room temperature is outside of the operational tolerances of the unit • The Cooling mode is not on • The compressor has not turned on yet because of its time delay • The set temperature is too high • The internal water reservoir is full and ‘P1″ appears on display	• This unit is designed to work in ambient temperatures of 63°F to 90°F. • Press the MODE button until the COOL light is shown on the display. • Give the compressor 3 minutes to turn on after the Cooling mode has been selected. • Set the air conditioner to a lower temperature. • It is recommended to set the temperature to at least 5°F of the ambient temperature. • Either manually drain the water by removing the drain plug or allow the unit to exhaust the water itself by running the fan only mode. Then cooling will resume. • Possible loose internal connection. • Please contact Whynter for service.
The air coming out of the unit is not very cold, or the airflow volume is weak	• The filter is dirty or obstructed • The air intake or exhaust is obstructed • The unit is set in DRY or FAN mode • The unit is set to low fan speed	• Clean the air filter • Make sure there is at least 20″ of clearance from the air intake. Make the length of the exhaust hose is as short as possible • Set the unit to the cooling mode • Set the unit to a higher fan speed

Many common portable air conditioner problems are easily resolved. Try the troubleshooting suggestions below to see if the problems can be resolved before having to contact the service department.

PROBLEM	POSSIBLE CAUSES	SOLUTIONS
The unit has worked for a long time, but the room is not cold enough	• Windows or doors are open • There are too many people in the room • There is direct sunshine into the room • The room is a kitchen or with many heat producing appliances • There is a server in the room • The room is too large	• Close all windows and doors • You may need additional cooling or another air conditioner. • Close curtains or blinds and try to minimize the amount of direct sun-light into the room. • You may need additional cooling or another air conditioner.
The unit is very noisy	• The unit is not level • The surface underneath the unit is uneven • Low power voltage	• Make sure the unit is on hard, level and stable surface. • Move the unit to a location with a level and hard floor. • Make sure the wall outlet and support the required power consumption of the air conditioner and do not use an extension cord.
The unit leaks water	• The unit is tilted or not leveled • The water tank is full	• Make use the unit is leveled • Drain water from the drain plug at the back of the air conditioner
Fan speed cannot be changed	• Fan speed differences are not very noticeable	• The fan speed difference is not very noticeable when the compressor is on. Try setting the unit to Fan only mode, you should be able to hear the difference between high and low fan speed settings.

Pros & Cons

Pros

Efficient Cooling: Quickly cools small to medium-sized rooms.
Multi-Functional: Includes dehumidifying and air purification functions.
Portable Design: Easy to move around with caster wheels.
User-Friendly Controls: Simple control panel and remote control operation.
Energy Efficiency: Runs on standard 115V power outlet.

Cons

Noise Level: Can be noisy on high fan settings.
Drainage Maintenance: Requires regular emptying of condensate tank.
Exhaust Hose Installation: Requires careful setup to ensure proper ventilation.
Weight: May be heavy for some users to move around.

Customer Reviews

Customers have praised the Whynter Portable Air Conditioner ARC-1230WNH for its effective cooling performance, especially in hot summer months. Many users appreciate its multi-functional capabilities and the ease of use. However, some reviewers have noted that it can be noisy and requires regular maintenance of the filters and condensate tank.

WARRANTY

ONE-YEAR LIMITED PARTS WARRANTY THREE WARRANTIES ON THE COMPRESSOR

This WHYNTER product is warranted to the original owner, purchased from an authorized Whynter dealer within the 48 U.S. continental states, for one year from the original purchase date against defects in material and work manship under normal residential usage. Should your WHYNTER product prove defective within one year from the date of purchase, contact Whynter’s Customer Support team with the serial number and proof of purchase to make a warranty claim.

Search Manuals in: arc-1230wnh

Read More