Introduction

The Monster Cable Automatic Voltage Stabilizer AVS2000 is an essential device designed to protect your home theater and audio equipment from voltage fluctuations. By ensuring a consistent output of 120 volts, it safeguards your components against power sags and surges that can degrade performance or cause damage. With features like programmable outlets and a safety overload disconnect, the AVS2000 combines functionality with reliability. This stabilizer is priced at approximately $1,499, reflecting its advanced technology and protective capabilities.

FEATURES

FRONT PANEL

Input/Output Voltage Meter: Displays input or output voltage.
Voltage Correction Meter: Continuously displays the amount of voltage being increased or reduced to maintain 120 volts.
Current Usage Meter: Displays current draw.
Ground OK LED: Indicates the wall outlet that AVS 2000 is plugged into is properly grounded.
Surge Protected LED: Indicates AVS 2000’s internal surge protection is active.
Line and Neutral OK LED: Indicates the wall outlet that AVS 2000 plugged into is properly wired.
Normal Voltage Condition: Indicates input voltage is between 80 and 140 volts.
Switched Outlets On LED: Indicates components plugged into the “switched” outlets will receive power when the ON button is pressed.
Abnormal Voltage Condition: Indicates input voltage has dropped below 80 volts or has risen above 140 volts or that the system is waiting for stabilization.
Sequential Power On/Off Button: Press to provide AC power to switched outlets.
Input Voltage/Readout Illumination: Adjusts the illumination level of the LED meters (depress and hold). Toggles input/output voltage meter (depress and release).

BACK PANEL

Unswitched Outlets: Provide power to components or Monster PowerCenters regardless of the status of the Sequential Power On/Off button (10).
Switched Outlets: Provide power to connected components only when the Sequential Power On/Off button (10) is initiated.
Delay Programming: Sets the powerup delay time for the switched outlets (see Fig.3, below left).
3-30v DC In: Allows AVS 2000’s “power on” function to be controlled by other remote enabled units (such as the Monster Power® Home Theater Reference HTS 5000 PowerCenter).
6-12v DC Out: Allows AVS 2000 to control other remote enabled units “power on” function.
Thermal Circuit Breaker: Protects the AVS 2000 from power overload.
Ground Post: Provides a ground reference point for ungrounded components.

Specifications

Automatic Voltage Regulation: Adjusts output voltage to a stable 120V ± 5%
Surge Protection: Protects against power surges and spikes up to 6000 joules
Overvoltage Protection: Shuts off power if voltage exceeds safe levels
UnderVoltage Protection: Prevents damage from low voltage conditions
8 Outlet Design: Includes 4 switched and 4 always-on outlets
LED Indicators: Displays input voltage, output voltage, and fault conditions
Durable Construction: Built with high-quality materials for long-lasting performance

Descriptions

The Monster Cable AVS2000 boasts a robust design with a sleek and compact footprint, making it easy to integrate into any setup. The device features an intuitive interface with clear LED indicators that provide real-time feedback on input and output voltages, as well as any fault conditions. The eight-outlet design allows you to connect multiple devices simultaneously, with four switched outlets for devices that do not require constant power and four always-on outlets for critical components like routers and modems.

The AVS2000 is engineered with advanced surge protection and automatic voltage regulation, ensuring that your equipment receives a stable and safe voltage supply at all times. This not only protects your devices from potential damage but also helps in maintaining their performance and longevity.

SWITCHED OUTLETS

Outlet banks 1-4 of your AVS 2000 are “switched” outlets.This means you can program them for sequential turn-on. Sequential turn-on is one of AVS 2000’s key features, helping maintain the peak performance of your components. Without sequential turn-on, you’d power all your devices at once, causing unnecessary electrical stresses known as “turn-on surge.”Turn-on surge can overheat system connections, pop circuit breakers, and degrade overall system performance. By sequentially powering your high power loads, you can prevent turn-on surges and deliver all the stable voltage needed to maintain peak performance.

The four switched outlets located on the back of the AVS 2000 can be individually programmed to delay power-up between 1 to 6 seconds.This means in order to program each outlet, you must use the slide switches seen in Figure 3.

OUTLET PROGRAMMING

SAFETY PRECAUTIONS

WARNING Power Sources
Do not plug your Monster AVS 2000 into a power outlet that differs from the source indicated for safe use on the Monster AVS 2000. If you don’t know the type of electrical power that is supplied to your home,please consult your local power company.

WARNING – Grounding and Polarization

Your Monster AVS 2000 has a three-wire grounding-type AC plug (a three-prong plug). This plug is designed to be inserted into a grounding-type outlet only. If this plug doesn’t fit directly inside your outlet, do not attempt to force it into the outlet. Contact a local electrician to install the proper polarized outlet. Never attempt to dismantle the plug in any way (or to alter an extension cord) to make it fit into a two-prong outlet. Do not attempt to defeat the grounding feature by using a 3-to-2 prong adapter. Instead, call a local electrician to install a properly grounded outlet.
If you use rooftop devices such as satellite dishes, antennas, or any other component with wire that connects to your AVS 2000, be sure the wire(s) is properly grounded. Use grounding techniques specified in Section 810 of the National Electrical Code (NEC), ANSI/NFPA 70 (in Canada, Part 1 of the Canadian Electrical Code). This protects against voltage surges and static charges.Do not place any part of an antenna near overhead power lines,or any other power circuit. Do not touch any power line or power circuit. Doing so may cause you severe physical injury and possibly result in death.
WARNING – Storm Precautions
In the event of a lightning storm, immediately disconnect incoming signal and power lines (e.g., cable and telephone).
WARNING – No User Serviceable Parts Inside
If, for any reason, your Monster AVS 2000 is not operating properly, do not remove any part of the unit (cover, etc.) for repair. Unplug the unit and consult this owner’s manual for warranty and service information.
CAUTION – Exposure To Heat
Do not expose your Monster AVS 2000 to direct sunlight or place it near wall heaters, space heaters, or any enclosed space prone to temperature increase (e.g., car trunk).
WARNING – Liquid: Avoiding Electrical Shocks
Do not operate your Monster AVS 2000 if liquid of any kind is spilled onto or inside the unit. Do not operate your Monster AVS 2000 near rain or water that’s spilled or openly exposed (e.g., bathtub, kitchen or bathroom sink).
WARNING – Power Cord Safety
1. When routing your Monster AVS 2000 AC power cord, do not place it near heavy foot traffic areas (e.g., hallways, doorways, and kitchen floors). Do not create a trip hazard with the power cord.
2. If your power cord’s protective jacket begins to rip or fray, exposing the internal wiring, shielding, etc., disconnect it from the power source and discontinue use of the Monster AVS 2000 immediately. Please see warranty information.
WARNING – Proper Cleaning
In general, the only cleaning necessary for your Monster AVS 2000 is a light dusting. Unplug your component from the wall outlet before cleaning it. Do not use any type of liquid or aerosol cleaners.
WARNING – Medical Conditions
AVS 2000 is not designed for use with any medical equipment.

Setup Guide

To set up the Monster Cable AVS2000, follow these steps:

Place the stabilizer on a flat surface in a well-ventilated area.
Connect the power cord to a wall outlet.
Plug your electronic devices into the appropriate outlets (switched or always-on).
Turn on the AVS2000 by pressing the power button.
Monitor the LED indicators to ensure proper functioning and stable voltage output.

No complex configuration is required; the device is ready to use as soon as it is powered on.

Stabilizer AVS2000 TROUBLESHOOTING

PROBLEM – The AVS 2000 is not receiving power.
Possible Cause #1
The AVS 2000 is not turned on.
SOLUTION
- Make sure the AVS 2000’s AC power plug is plugged into a properly grounded 120V wall outlet.
- Press the ON button on the AVS 2000.
- In some households, a wall switch may need to be thrown to make the wall outlet come alive. Try turning on the light switches located near the wall outlet powering the AVS 2000.
PROBLEM
Possible Cause #2
Too many devices are connected, causing an overload, tripping the thermal circuit breaker.
Please note: The total power consumption on all the components powered by a single AVS 2000 should not exceed 1440 watts continuous or 1800 watts peak.
SOLUTIONS
- Disconnect any component that may be overloading the AVS 2000.
- Press the AVS 2000’s thermal circuit breaker (labeled BREAKER 15A on the back panel) button in to reset. Please allow 10 minutes from the time the circuit breaker is initially tripped before attempting to reset. If you reset too soon, the breaker will prematurely sense power overload and not allow unit to operate.
PROBLEM
Possible Cause #3
The AVS 2000 is defective.
SOLUTION
- Please see warranty information.
PROBLEM – AVS 2000 is not providing power to the components.
Possible Cause #1
The component is plugged into a “switched outlet” and the AVS 2000 has not been turned on.
SOLUTIONS
- Press the ON button on the AVS 2000 and wait for a few seconds for the components plugged into the AVS 2000’s “switched outlets” to be turned on.
- Or, plug the component into an “unswitched” outlet.
Possible Cause #2
The AVS 2000 is defective.
SOLUTION
- Please see the warranty information.

WARRANTY INFORMATION

PRODUCT WARRANTY
Home Theatre Reference Automatic Voltage Stabilizer AVS 2000 offers a Limited 2 Year Product Warranty. Monster Cable Products,Inc. warrants that this product shall be free of defects in materials and workmanship under normal use for its lifetime.

Monster Cable Automatic Voltage Pros & Cons

Pros

Effective surge and spike protection
Automatic voltage regulation for stable power supply
User-friendly interface with clear LED indicators
Durable construction with high-quality materials
Compact design with multiple outlet options

Cons

Slightly higher cost compared to basic surge protectors
Noisy fan operation in some units (rare cases)
Limited availability in certain regions

Customer Reviews

Customers have praised the Monster Cable AVS2000 for its reliability and effectiveness in protecting their electronic equipment. Many have noted that the device has saved their gear from several power anomalies, ensuring uninterrupted operation. However, some users have reported occasional issues with the fan noise and limited availability.

Most Common Complaints

A common complaint is that the device can be a bit bulky for smaller setups, but overall, it is highly recommended for its robust features and performance.

Search Manuals in: avs2000

Read More