Introduction of Modern Masters Metal Effects Copper Paint MDM-09

The Modern Masters Metal Effects Copper is a high-quality, professional-grade paint that provides a stunning metallic finish to any project. This paint is perfect for creating a distressed, aged, or rusted copper appearance, and it can be used on a variety of surfaces, including metal, wood, and plastic. With an estimated price of $24.99 and a launch date of January 2021, this paint is a must-have for any DIY enthusiast or professional craftsperson.

DESCRIPTION AND USES

The Metal Effects Copper Paint MDM-09 is a water-based, acrylic paint that provides a smooth, even finish. It has a high-pigment load, which means that a little goes a long way, and it can be easily brushed or sprayed on. This paint is also self-priming, which means that it can be applied directly to most surfaces without the need for a separate primer. The MDM-09 paint is designed to mimic the look of real copper, and it has a rich, warm color that is perfect for creating a variety of different finishes. Modern Masters® Metal Effects® Oxidizing Copper Paint is a water-base, modified acrylic paint with a high concentration of real copper particles. It will tarnish naturally over time, if exposed to the proper elements, but Metal Effects Green Patina Aging Solution will speed up the oxidation process to create a beautiful authentic green patina finish in minutes. The entire system can be applied to any properly prepared surface, including metal, wood, drywall, plaster, paintable wall coverings, canvas or muslin, and plastic surfaces. Popular applications range from full interior and exterior walls, moldings, trim, columns, doors, railings, to lamps, vases, and planters.
PRODUCTS

PRODUCTS	6 Oz.	16 Oz.	GALLON	DESCRIPTION
ME14906	ME14916	ME149GAL	Copper
PA90104	PA90116	PA901GAL	Green Patina

RECOMMENDED PRIMER

RECOMMENDED PRIMER	4 Oz.	16 Oz.	GALLON	DESCRIPTION
AM20304	AM20316	AM203GAL	Metal Effects Primer

Note: Lower temperature and higher humidity will lengthen the dry and cure times of primers

Setup of Modern Masters Metal Effects Copper Paint

Setting up the Modern Masters Metal Effects Copper Paint MDM-09 is easy. Before you begin, make sure that the surface you will be painting is clean, dry, and free of any dirt, dust, or debris. If necessary, use a mild detergent and water to clean the surface, then allow it to dry completely. Once the surface is ready, shake the paint can well to ensure that the pigments are evenly mixed. Then, using a brush or sprayer, apply the paint in thin, even coats. It is important to allow each coat to dry completely before applying the next one, as this will help to ensure a smooth, even finish.

COMPATIBLE PRIMERS

METAL SUBSTRATES
Sierra Performance™ Griptec™
Sierra Performance™ Metal Max Gray Primer Substrates: galvanized metal X-I-M UMA

Substrates: aluminum metals, copper piping, window and door mullions Rust-Oleum ROC PRIME
Substrates: rusting metal, slag steel

PRODUCT APPLICATION

SURFACE PREPARATION

ALL SURFACES: Remove dirt, grease, oil, salt and chemical contaminants by washing the surface with a commercial detergent or other suitable cleaner. Rinse thoroughly with fresh water and allow to fully dry. If any mold or mildew is present on the surface clean further with one quart of household bleach added to a gallon of water. Rinse with clean water. Severely mildewed areas should be cleaned with a chlorinated cleansing powder and thoroughly rinsed with water. All surfaces must be dry at time of application.
SURFACE PREPARATION
PREVIOUSLY COATED: Previously coated surfaces must be sound and in good condition. Smooth, hard or glossy finishes should be scarified by sanding to create a surface profile.
WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop.
APPLICATION
Modern Masters Metal Effects paints can be brushed, rolled, or spray applied (See specific equipment requirements under Spraying) onto any paintable, properly primed, interior or exterior surface, such as walls, ceilings, columns, trim, doors, furniture, and paintable wallcoverings. Always test the product in a small, inconspicuous area before beginning a project to see if the desired results are attained. We recommend preparing a sample board prior to beginning a project to check color and technique. The paint should be mixed thoroughly before using.
Do not apply in temperatures below 55°F/13°C or above 85°F/29°C.
- BRUSHING: Use a high-quality brush recommended for water base semi-gloss paints.
- ROLLING: To roll Metal Effects Copper Paint use a high-end ½” nap roller and/or a natural sea sponge roller for added effect.
- SPRAY: The Metal Effects Copper Paint can be spray applied using conventional air atomized spray or HVLP. Thin with clean, fresh water up to 12.5% by volume, one pint (16 fl. oz.) per gallon. Do not over thin as this can result hide and appearance. The actual amount of thinning will depend on the type of spray equipment being used. Be sure the air supply is clean and oil free.
SPRAY
Examples:
- Binks-Mach 1 HVLP, with a 94-nozzle set up (0.55 or 1.4mm diameter fluid tip and a 90P air nozzle). The settings for this equipment were: Fluid Pressure-25psi and Air Pressure-45psi.
- Binks-2001 Conventional, with a 66SS air nozzle set up (0.70 or 1.8 fluid tips and a 66SD air nozzle). The settings for this equipment were: Fluid Pressure-30psi and Air Pressure-60psi.
- Use a NIOSH approved respirator when spraying. Provide adequate ventilation. Note: Do not use turbine-type “air compressors” to power the HVLP spray gun and do not use airless spray systems.
Taping: Use high quality, low-tack tape when taping over surfaces that have been previously painted with Metallic Paint. When painting over taped-off areas be aware that Metallic Paints exhibit poor early adhesion properties and are elastomeric (they stretch) before curing. Consider cutting along the tape edge with a razor blade to avoid delaminating the fresh paint from the substrate.
APPLICATION INSTRUCTIONS
- Apply at least two coats of Metal Effects Primer to completely seal and block the surface. Some metal surfaces, such as bare aluminum, galvanized metal, or rusted or slag metals, will need a specialty primer from our recommended primer list, applied prior to the application of Metal Effects Primer. If this is the case, read the specific information for the recommended primer prior to beginning your project.
- Apply first coat of Metal Effects Oxidizing Copper Paint and allow to dry. Apply a second coat of Metal Effects Oxidizing Copper Paint in the same manner. The Green Patina Aging Solution should be applied while this coat is still wet (within 5 minutes).
- Apply the Green Patina Aging Solution with a brush, sea sponge or spray apply with a plastic pump sprayer. As the activated surface dries (approx. 30-40 min.) a real patina finish will appear. Cold temperature and/or humid conditions will prolong the oxidation process and dry time.
- (Optional) Protective Clear Coating – Patina finishes do not require a clear protective finish, except if the patina surface is subject to repeated hand contact, such as hand rails. If a protective sealer/topcoat is desired, use Metal Effects Permacoat Xtreme. DO NOT USE OTHER
SEALERS OR VARNISHES. Permacoat Xtreme can be applied by brush, roller or spray. Surface must be completely dry prior to top coating (minimum of 24 hours). First coat: Add equal parts of Permacoat Xtreme with water and stir well before applying. Second coat: Apply Permacoat Xtreme at full strength. Let surface dry for 1 hour before handling. Full cure time is 7 to 10 days.
DRY TIMES: Recoat time is approximately 30 minutes. Dry-to-touch time is approximately 1 hour. (Drying times were recorded at 70°F and 50%RH.)
Note: Lower temperature and/or higher humidity will lengthen the dry and cure times.
CLEAN UP: Clean brushes, rollers, tool, and equipment with soap and warm water immediately after use. Promptly wipe up spills and splatters with a damp cloth.
HANDLING & STORAGE: Close tightly all containers when not in use. Store in a cool dry place away from direct sunlight. Do not freeze. If Metal Effects Oxidizing Copper Paint becomes frozen, allow the paint to completely thaw and come to room temperature before use. Stir thoroughly before use.
DISPOSAL: Dispose of unused or unwanted product in accordance with local laws regulating water-based coatings.

PHYSICAL PROPERTIES

PHYSICAL PROPERTIES	OXIDIZING COPPER PAINT	GREEN PATINA
Resin Type	Water-Based Acrylic	NA
Active Ingredient	NA	Hydrochloric acid
Pigment Type	Copper and iron	NA
Solvents	Water, Glycol Ethers	Water
Weight	Per Gallon: 10.32 lbs.	8.62-9.65 lbs
	Per Liter: 1.24 kg	1.03-1.04 kg
Solids	By Weight: 39.52%	7.80-7.84%
	By Volume: 25.37%	4.61%
Volatile Organic Compounds	<100 g/l	0 g/l
Recommended Dry Film Thickness (DFT) per Coat	1.5 mils	0.25 mils
Wet Film to Achieve DFT (Unthinned material)	6 mils	5.5 mils
Practical Coverage at Recommended DFT (assume 15% material loss)	210-270 sq.ft./gal.	230-290 sq.ft./gal.
Dry Times at 77°F (25°C) and 50% Relative Humidity	Touch: 1 hour	NA
	Handle: 2 hours
	Recoat: 2 hours
	Full Cure: 3-4 hours
Shelf Life	5 years
Flash Point	>200°F
Storage	40-90°F (4-32°C)
Safety Information	For additional information, see SDS

Troubleshooting of Modern Masters MDM-09

If you experience any problems while using the Modern Masters Metal Effects Copper Paint MDM-09, there are a few things you can try. If the paint is too thick, thin it with a small amount of water. If the paint is not covering the surface evenly, apply additional coats as needed. If the paint is not drying properly, make sure that the surface is in a well-ventilated area and that the temperature is above 50°F. If the paint is cracking or peeling, this may be due to applying the paint over a dirty or improperly prepared surface. To fix this, clean the surface and apply a fresh coat of paint.

Pros & Cons of Metal Effects Copper Paint

Pros

Provides a stunning metallic finish
Can be used on a variety of surfaces
High-pigment load for excellent coverage
Self-priming for easy application

Cons

May require multiple coats for full coverage
Water-based formula may not be as durable as oil-based paints

Customer Reviews of Modern Masters Metal Effects Copper Paint MDM-09

Customers who have used the Metal Effects Copper Paint MDM-09 have given it high marks for its ease of use, high-quality finish, and versatility. Some have noted that it can be a bit tricky to apply evenly, but with a little practice, most have been able to achieve excellent results. The most common complaint is that the paint is a bit on the expensive side, but most customers agree that the high-quality finish is worth the extra cost.

Search Manuals in: metal-effects

Read More