Ozeri 3X Tower Fan OZF3 Introduction

Tower Fanis a sleek and efficient cooling solution designed for modern living spaces. Standing at 44 inches tall, it features Passive Noise Reduction Technology for quiet operation, making it ideal for bedrooms or offices. With three fan speeds and an oscillation function, it provides customizable airflow to enhance comfort. The fan is priced at approximately $79.99, offering a blend of performance and style for users seeking effective cooling solutions.

GENERAL SAFETY

Warning: When using electric appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock and personal injury, including (but not limited to) the following:
Read all these instructions before attempting to operate this product and save these instructions for future reference:

THIS FAN HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER). TO REDUCE THE RISK OF ELECTRICAL SHOCK, THIS PLUG IS INTENDED TO FIT IN A POLARIZED OUTLET ONLY ONE WAY. MATCH THE WIDE BLADE OF PLUG TO THE WIDE SLOT OF THE OUTLET. FULLY INSERT. IF THE PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED ELECTRICIAN. DO NOT ATTEMPT TO BYPASS THIS SAFETY FEATURE.

NOTE: THIS FAN IS EQUIPPED WITH A FUSE. ALWAYS UNPLUG THE FAN BEFORE REPLACING FUSES. IF THIS FAN LOSES POWER AND YOU SUSPECT THE FUSE IN THE PLUG HAS BLOWN, UNPLUG THE FAN, THEN SLIDE THE FUSE DOOR FOUND ON THE SIDE OF THE PLUG TO THE OPEN POSITION. SLIDE THE FUSE DOOR OUTWARD UNTIL THE BLOWN FUSE IS FULLY VISIBLE. REMOVE THE BLOWN FUSE AND SNAP THE REPLACEMENT FUSE INTO PLACE. FULLY CLOSE THE FUSE DOOR. ONLY REPLACE WITH A FUSE RATED AT 2.5 AMPS, 125 VOLTS.

Ozeri -OZF6-Dua-Oscillating 10” Desk Fan

Use this fan only as described in this manual.
Check the voltage indicated on the rating plate. This fan is designed for a 120V-60Hz electric supply. Make certain the power source conforms to these electrical requirements. Make sure the room where this fan will be used has a working smoke detector.
Assemble the fan completely before use.
Do not use an electrical extension cord with this fan. Do not plug the fan into a power strip. The use of such devices may create electric and/or fire hazards.
Do not force your fingers through the ventilating slits. Do not allow any foreign objects through the ventilating slits.
This product is not a toy. Do not allow children to tamper with the fan.
Be careful not to allow hair, curtains, tablecloth, clothes or other nearby objects block the airways of the fan or to enter the openings of the fan. This can cause damage and/or injuries.
Do not use this or any fan if the cord is found to be or becomes damaged. Periodically check the electric cable of this fan. If the electric cable is damaged, it must be replaced by the manufacturer, its after-sales service or by a similar qualified person in order to avoid danger.
Do not use this fan if it falls and/or becomes damaged in any way. If the fan becomes damaged, it must be replaced by the manufacturer, its after-sales service or by a similar qualified person in order to avoid danger.
Do not use this fan outside, or in any commercial, industrial or agricultural setting. This fan is only for indoor residential use. Do not use this fan with any solid state speed control devices.
Do not use this fan in a damp area such as bathroom.
Do not use this fan on a window, ledge, or on any unstable platform. The fan should only be used standing on its base. Never lay the fan on its side.
Do not use this fan next to a window or anywhere where exposure to rain or moisture is possible. This may create an electric hazard.
Do not place the electrical cord under any objects, such as carpets, throw rugs or runners. Do not place electrical cord in areas of foot traffic where there is a risk of stumbling or tripping over it.
The fan must always be unplugged when not in use. Before unplugging the fan, first ensure it has been turned off.
Do not operate the fan in an area where gasoline, paint supplies or any flammable liquids or explosive chemicals are used or stored.
Do not try to repair or disassemble this fan. Doing so will void the warranty and may result in damage and/or personal injury. There are no end-user serviceable parts.
Always use the fan in an upright position. Ensure the fan stands on a firm, solid, even floor (do not place fan on thick pile carpets).
Remote control devices for other appliances may interfere with this fan and vice-versa. If this occurs, move the fan to another location.
Always store the remote control inside the fan’s remote control compartment. This fan is not suitable for use in agricultural facilities and hazardous locations. This fan does not meet the requirements of NEC Article 547-7 and 500 (2002).
Keep this fan and all electrical appliances out of reach from children at all times.
WARNING: Always turn off and unplug the fan when leaving the area. Never leave children unsupervised with access to this fan. There are no serviceable parts in this fan. Do not attempt to disassemble or repair this product.

Technical Specifications

Rated voltage 120V / 60Hz
Rated Frequency 50Hz
Rated power 90W
Net weight of Fan 12.76 lbs
Gross weight in Box 18 lbs
Noise < 55dB
Oscillation Angle: 90˚
Unit height 44.1”
Suitable environment
32 – 104 F, relative humidity 85%

Features:

3 Independently Controllable Fans
Front LED Indicators
Touch Screen Operation
Remote Control Unit
Horizontal Oscillation
Programmable Timer: 0.5~7.5 hours
3 Wind Speeds (Low, Med, High)
3 Wind Modes (Normal, Nature, Sleep)
Easy Assembly

COMPONENT LIST

Remote Control
Main Body
Stand
Base
Locking nut
Power Cord & Plug

Description

The Ozeri 3X Tower Fan OZF3 boasts a sleek and contemporary design that complements any interior. Its slim profile allows it to fit into tight spaces, making it perfect for small rooms or apartments. The fan features a sturdy base that prevents it from tipping over, ensuring safety and stability.

The fan's advanced 3X airflow technology ensures that air is circulated efficiently throughout the room, providing a cooler and more comfortable environment. The canted fan blades are designed to maximize airflow while minimizing noise, making it suitable for use during sleep or in quiet environments.

Ozeri 3X Tower Fan OZF3 ASSEMBLY

Unpack the fan and check that you have all of the components.
Turn the fan upside down and remove the plastic nut from the stand pole.
Assemble the two halves of the base (plastic base only), place the base onto the stand and lock into position with the nut.

Note: Ensure the nut is tight to avoid shaking of the fan.

REMOTE CONTROL STORAGE

The remote control is stored in the remote control holder located at the top of the rear enclosure as shown in Fig 2.

REPLACING THE BATTERY

Your remote control is powered by an included CR2032 Lithium battery. To replace the battery, pull out the battery holder and insert a new battery.
Ensure that the polarity is correct and then insert the battery holder back into the remote control (Fig 3 and 4).
When the fan’s power is on, the remote control can be used to operate the fan from up to 20 feet away.
Note: if there are two or more fans within this distance, both will be operated by the same remote control.
If the remote control will not be used for a long period of time, remove the batteries from the battery compartment

OPERATION

Insert the plug into the power outlet.
The fan is operated by a ‘touch’ screen control panel.
Touch the button to turn the fan on. Select the desired fan speed (low-medhigh) by touching this button. Each touch will cycle between the speeds.
Turn the fan OFF by touching the button at any time.

MODES

The fan has 3 modes of operation: Normal, Nature and Sleep. Touch the button to cycle between these modes.

Normal mode: The fan will work continuously at the selected speed setting.
Nature mode: is shown and if set at high speed, the fan will cycle between high, medium and low speeds for 5 seconds each. If the fan speed is set to medium, the fan will cycle between medium and low. If set to low, the fan will cycle between low and off.
Sleep mode: is shown and if set at high speed the fan will first work at high speed nature mode for 30 min, then at medium speed nature mode for 30 min, then continue working at low speed nature mode.

Note: This fan’s LED screen is equipped with an automatic auto-dimming feature that reduces the brightness of the LED screen after 2 minutes of inactivity. This reduces energy usage and helps reduce ambient lighting when darkness is preferred.

SWING FUNCTION

Touch the button on the control panel to enable the swing function. The control panel will display the symbol and the fan will swing from side to side in a 90° arc. Touch again to stop oscillation.

Note: Do not force or hinder the oscillation movement

TIMER FUNCTION

The fan has a timer function that will turn off the fan. By touching the button 0.5 to 7.5 hour delays are available. The timer will count down as it progresses - i.e. if 2 hours is set, after 30 minutes 1.5 hours will show as the remaining time on the display. To cancel, touch the button until the timer indicators are no longer lit.

SHIFT FUNCTION

As well as the fan speed control, the fan is also equipped with the ability to turn each of the three different fans on or off.
Touch the button. “FAN1”, “FAN2” and “FAN3” will flash on the display for 5 seconds.
During this time, touch the , or buttons to turn FAN1, FAN2 or FAN3 off or on.

NOTE: If all fans are turned off, this is the same as touching the button.

Setup Guide

To set up the Ozeri 3X Tower Fan OZF3, follow these steps:

Unpack the fan and all included accessories from the box.
Assemble the fan by attaching the base to the tower unit. Make sure it is securely locked in place.
Plug in the fan and turn it on using the power button on the remote control or the touch-sensitive buttons on the LED display.
Adjust the fan speed to your desired level using the remote control or the buttons on the fan.
If needed, set the timer function for automatic shut-off up to 8 hours.

MAINTENANCE

To maintain the airflow efficiency, clean the inlet and outlet grilles on a regular basis, first taking care to observe the following:

Unplug the fan from the power supply before cleaning.
Use a soft, damp cloth to wipe the outside. Use only water to dampen the cloth. Never immerse the fan in water. Never use thinners or other cleaning solutions, as these may damage the fan’s surface appearance.
Use a vacuum cleaner to remove dirt and dust from the inlet and outlet grilles.
Ensure the fan is completely dry before plugging the cord back into a power supply.
If the fan will not be used for an extended period of time, unplug the fan and store it in a cool dry indoor location, taking care to ensure the fan is stored vertically on a level hard floor.

CAUTION: THIS FAN HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER). TO REDUCE THE RISK OF ELECTRICAL SHOCK, THIS PLUG IS INTENDED TO FIT IN A POLARIZED OUTLET ONLY ONE WAY. MATCH THE WIDE BLADE OF PLUG TO THE WIDE SLOT OF THE OUTLET. FULLY INSERT. IF THE PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED ELECTRICIAN. DO NOT ATTEMPT TO BYPASS THIS SAFETY FEATURE.

WARRANTY INFORMATION

Your Ozeri 3x Tower Fan is warranted to the original owner for 1 year from the date of purchase against defects in material and workmanship under normal use and service. Should your Ozeri Fan prove defective within 1 year from the date of purchase, return the defective product, freight prepaid along with your receipt and an explanation of the claim to “Ozeri.”

Troubleshooting

If you encounter any issues with your Ozeri 3X Tower Fan OZF3, here are some common problems and solutions:

Fan does not turn on: Check if the fan is properly plugged in and if the power button is functioning correctly.
Noisy operation: Ensure that the fan is assembled correctly and that there are no obstructions blocking the airflow.
Try replacing the batteries or checking for any interference from other electronic devices.

Always refer to the user manual for detailed instructions and warnings to ensure safe and proper use of the product.

Pros & Cons

Pros:

Advanced 3X airflow technology for enhanced cooling
Quiet operation with reduced noise levels
Sleek and space-saving design
Energy-efficient with low power consumption
Timer function with automatic shut-off
Remote control for convenient operation

Cons:

May not be as effective in extremely large rooms
Some users may find the LED display too bright in dark rooms
Limited availability in some regions

Customer Reviews

Customers have generally praised the Ozeri 3X Tower Fan OZF3 for its powerful airflow, quiet operation, and modern design. Many users appreciate the ease of use and the convenience of the remote control. However, some users have noted that it may not be as effective in very large rooms and that the LED display can be too bright in dark environments.

Most common complaints include issues with the remote control batteries draining quickly and minor assembly difficulties.

Search Manuals in: ozf3

Read More