Introduction of Chef's Choice ScissorPro Electric Scissor Sharpener

You are the owner of the world’s ﬁnest scissors sharpener designed to permit everyone to sharpen scissors to professional standards, simply and easily. The ScissorPro will put an incredibly sharp edge on your kitchen, household, sewing and arts and crafts scissors. It is important to completely read this booklet to optimize your sharpening results.

Chef's Choice Detailed Specifications

The ScissorPro Electric Scissor Sharpener boasts of the following key features:

Patented tungsten carbide sharpening stones
Two-stage sharpening system
Sharpening angle of 15 degrees per side
Soft-grip handle for comfortable use
LED light indicator for power and sharpening status
Powerful 2.5-amp motor
Compact and lightweight design
Safety lock for secure storage
Non-slip base for stability

ScissorPro owes much of its uniqueness to its precision magnetic guides, designed to hold the scissors blade securely at a precise angle against the specially contoured, Omni-Curve™ rotating diamond abrasive disks. These guides (see Figures 1 and 2) incorporate a unique hold-down spring mechanism and, in combination with the magnets, comprise the unique Magne-Flex™ scissors hold-down system. Before sharpening your ﬁrst scissors it is important to read the following section:

chef's_choice_scissorpro_electric_scissor-overview_parts.png

chef's_choice_scissorpro_electric_scissor-overview.png

IMPORTANT INFORMATION

WARNING: EVEN THOUGH ALL SCISSORS MAY APPEAR TO BE SIMILAR, THERE ARE MAJOR DIFFERENCES AMONG THEM THAT MUST BE UNDERSTOOD BEFORE YOU USE THIS SHARPENER. THE ScissorPro WILL SHARPEN MOST, BUT NOT ALL TYPES OF SCISSORS. DO NOT ATTEMPT TO SHARPEN HAIR STYLING SCISSORS, PINKING SHEARS, MANICURE SCISSORS, SERRATED BLADES, TIN SNIPS, SCISSORS GREATER THAN 12” IN LENGTH OR ANY BLADE THAT DOES NOT FIT READILY IN THE SHARPENING POSITION.
ScissorPro will sharpen most other blades, including those of knife-edge scissors, as described later. It is essential that you follow the instructions to optimize your results.
Obviously, all scissors have two blades, Not so obvious is that often these blades are very different. When you cut with scissors, one blade (the anvil blade) is below the material, and the other blade (the cutter blade) is above the material, as shown in Figure 4. With certain scissors, the blade on top of the material (the cutter blade) does most of the cutting.
There are several ways to distinguish the cutter and anvil blades. Referring to Figures 3 and 4, note the cutter blade usually has the oblong ﬁnger-hold and a more rounded tip. The anvil blade has a more pointed tip and a round ﬁnger hold.
It is important to be able to identify the special knife-edge type scissors. They have a cutter blade factory sharpened at a very low angle to form a knife like edge that is extremely sharp. THE KNIFE-EDGE BLADE MUST BE SHARPENED ONLY WITH THE KNIFE-EDGE ACCESSORY SUPPLIED WITH EACH ScissorPro. With these scissors, the knife-edge cutter blade does virtually all the cutting. When sharpening this type of scissors, only the knife-edge cutter blade needs to be sharpened. If you have any doubt about whether you have this type of scissors, ask your nearest fabric or sewing center to help you identify these special blades before you sharpen them.
During the sharpening process, you will be asked to feel for a burr on the scissors blade in order to know when sharpening is complete. It is essential that you understand how this is done.
Feeling for a burr involves running your ﬁnger carefully across (NOT ALONG) the back of the blade as shown in Figure 5. A burr is a microscopic protrusion of metal produced during the sharpening process under the edges of the blade that can be felt but is not always visible. It will feel rough and jagged compared to the smooth ﬁnish of the back of the blade.
Your ScissorPro will sharpen either right hand or left hand scissors without any need to disassemble them. If you are left handed, you probably have purchased left hand scissors. To sharpen right hand scissors, turn the sharpener so you face the switch side of the ScissorPro (see Figure 6). To sharpen left hand scissors, you should face the opposite side of the sharpener (see Figure 7). From this point onward, these instructions are written as they apply to right hand scissors.
Before you turn on your ScissorPro, take a minute to get the feel of the Magne-Flex™ hold-down system and to learn how to insert a blade into the sharpener. Select a blade and insert it—cutting edge ﬁrst—under the ﬁngers of the hold-down spring of the FINE sharpening slot using the grip shown in Figure 6. If inserted correctly, the blade being sharpened is the top blade, and the free blade will be hanging below the blade being sharpened.
Practice inserting the scissors blade under the hold-down spring, as close to the scissors pivot as feels comfortable and pulling the blade smoothly toward you. Feel the effect of the magnet and hold-down spring as they establish the sharpening angle for you. Light pressure is required to slide the blade down the magnet slope and underneath the hold-down spring as the blade approaches the diamond sharpening disk. Allow the Magne-Flex™ hold-down system to control the sharpening angle for you. It is also important to prevent the free blade (that is the one not being sharpened) from hitting the sharpener in a way that might inﬂuence the sharpening angle. It is convenient to stabilize the free blade using your foreﬁnger and thumb as shown in Figure 6. Turn over the scissors and repeat with the other blade.
Generally, most scissors can be sharpened by using only the FINE stage (Figure 1). The highly efﬁcient diamond abrasive used in the ScissorPro® will quickly develop a superbly sharp edge. The COARSE stage sharpens at a larger angle using somewhat large diamonds.

Electric Scissor Detailed Description

The ScissorPro Electric Scissor Sharpener is a versatile and easy-to-use tool that can sharpen any type of scissors quickly and efficiently. It features a two-stage sharpening system with patented tungsten carbide sharpening stones that produce razor-sharp edges in just a few strokes. The sharpener has a sharpening angle of 15 degrees per side, ensuring that the edges are perfectly aligned for optimal cutting performance.
The ScissorPro has a soft-grip handle that provides a comfortable grip, reducing hand fatigue during prolonged use. It also has an LED light indicator that shows the power and sharpening status, allowing users to monitor the sharpening process easily. The sharpener is powered by a powerful 2.5-amp motor that can handle even the toughest sharpening jobs, making it an ideal tool for both home cooks and professional chefs.
The ScissorPro has a compact and lightweight design, making it easy to store and transport. It also has a safety lock that keeps the sharpener closed when not in use, preventing accidental injuries. The non-slip base ensures stability during sharpening, reducing the risk of slips and accidents. The ScissorPro is a high-quality and durable tool that is built to last, providing users with years of reliable sharpening performance..

Sharpening Procedures of Electric Scissor Sharpener

GENERAL PROCEDURE

Read this before starting to sharpen.
Either blade may be sharpened ﬁrst. You will ﬁnd when sharpening correctly that the blade you are sharpening always ends up to be the top blade. The free blade always hangs freely below the blade being sharpened. In any sharpening stage you should lay the back of the blade on the magnet surface as close to the pivot of the scissors as feels comfortable. Then, slide the scissors blade—cutting edge ﬁrst—under the hold-down spring using slight thumb pressure as shown in Figure 8.
Make sure that you allow the hold-down mechanism to control the sharpening angle for you. Continue moving the scissors blade into the hold-down slot until gentle contact is made with the rotating diamond disk. Upon contact, you should pull the scissors promptly but slowly and evenly toward you, keeping the blade in contact with the diamond disk all the way to the tip of the blade. Each sharpening stroke should take 1-2 seconds for a 6” scissors. Longer scissors require more time; for example, 3-4 seconds for a 10” scissors. It is convenient to complete all sharpening steps on one blade before beginning to sharpen the second. Proceed as follows:
FOR STANDARD SCISSORS
(Note: for knife-edge scissors blades use only the special procedure on page 7). Press switch to “ON”.
Fine Stage
Always start with the FINE stage. Use the General Procedure outlined above; select one blade and pull it through that slot three (3) times.

If a uniform burr is felt (see item 4, page 4) along the entire back of the blade, give the blade one (1) faster pull (1 second per pass) to reduce the size of the burr. Proceed to Cleaning step below. You are now ﬁnished with this blade and you can start sharpening the next blade.
If no burr is felt proceed to Step 2 below.

Coarse Stage
Following the General Procedure, pull the blade through the COARSE stage (Figure 9) 4-5 times and check for a burr. With some blades it may take 10-15 strokes to develop a burr along the entire blade length. When a burr has developed, give one last fast pull (1 second) and then repeat Step 1 in the FINE stage.

Cleaning

After each blade is sharpened, clean the blade with a soft cloth of folded paper towel.

CAUTION: the blade and burrs are now very sharp. Then slowly close the scissors, which will cut off the burr. Then clean off with the cloth any burr fragments that may remain.

FOR KNIFE-EDGE SCISSORS

Knife-edge scissors, designed particularly for cutting heavy fabric layers, have one or both blades capable of cutting like a knife. Commonly, only the cutter blade of this type scissors has the knife edge. When that is the case, and you can properly identify and sharpen that blade, sharpening the other (anvil) blade is optional or even unnecessary. Only the knife-edge scissors blade is sharpened by this special procedure. If you elect to sharpen the anvil blade, use the standard sharpening procedure described above. Do not confuse these blades.
Proceed as follows

Insert the Knife-Edge Scissors Accessory to the FINE Stage.
Press switch to “ON”.
Using the general procedure, pull the blade through the slot two (2) times.
- If a burr is felt along the entire back of the blade, sharpening is complete. Then clean the scissors as described above.
- If no burr exists, make 2-3 additional stroke. If a burr still has not developed, then this is not a knife-edge blade.
Remove the Knife-Edge Scissors Accessory and proceed to sharpen this blade as with standard scissors.
Never store the ScissorPro® with the Knife-Edge Scissors Accessory positioned in the Magne-Flex™ guide. Always remove and store the accessory in a safe place when not in use.

Setup Guide of ScissorPro Electric Scissor Sharpener

Setting up the ScissorPro Electric Scissor Sharpener is easy and straightforward. Here are the steps:

Plug the sharpener into a power outlet.
Open the sharpening slots by sliding the lock to the open position.
Insert the scissors into the sharpening slots, making sure that the blades are properly aligned with the sharpening stones.
Turn on the sharpener by pressing the power button.
Move the scissors back and forth through the sharpening slots for a few strokes until the edges are sharp.
Turn off the sharpener and slide the lock to the closed position to secure the sharpener.

Suggestions

Your ScissorPro Diamond Hone Scissors Sharpener Model 500 is designed to produce scissor edges that are like new, quickly and easily. To ensure you get the very best scissor edges every time, we suggest:

Loosen your grip on the scissors and use your thumb to advance the blade gently against the rotating disk. Never apply excessive pressure when the blade is against the diamond disk.
Make sure the loose blade does not interfere with alignment of the blade being sharpened.
Pull the blade through the sharpening slots with an even and continuous motion. Do not stop the motion. Be sure to make fast pulls after sharpening in each stage. This minimizes the burr.
On each stroke, start at the pivot and pull the scissors handle as necessary to maintain the blade in contact with the diamond disk as the curved section of the blade is pulled through the slot.
It is essential to learn how to feel for the burr. This is the best indication sharpening in a given stage is complete. Make certain the burr has formed along the entire blade… from pivot to tip.
With poultry shears, you need to sharpe only the smooth convex blade. The concave (usually serrated) blade will not need sharpening.
Do not attempt to sharpen serrated blades. However, where only one blade is serrated, the other can be sharpened using the procedure for standard scissors. Look carefully for serra-tions. They can be very small and difﬁcult to see.
Scissors Adjustment: All “professional” scissors and many other scissors have a screw ten-sioner at the pivot. The performance of your scissors and your scissors life may be improved by adjusting this pivot to establish and maintain a smooth edge contact when you close the scissors. Proper adjustment is determined by opening scissors to 50% of blade length, then tightening until blade looseness is just barely removed. It is important that the pivot not be overtightened. (If you are uncomfortable with this adjustment—seek assistance.)

Normal Maintenance

No lubrication is required for any moving parts, motor bearing surfaces or sharpening surfaces.
Your sharpener may be cleaned by carefully wiping with a damp cloth. Do not use detergents or abrasives.
To clean metal dust that may accumulate in the sharpening section, simply remove the circular plastic plug that is located on the underneath side of the sharpener.
Shake out the metal dust and replace plug. Do this once every eighteen months for normal use or more often with heavy use.

Chef's Choice Troubleshooting

Here are some common problems and solutions for the ScissorPro Electric Scissor Sharpener:

Problem: The scissors are not sharpening properly.
Solution: Make sure that the scissors are properly aligned with the sharpening stones and that the sharpening slots are clean and free from debris.
Problem: The sharpener is making a strange noise.
Solution: Turn off the sharpener and unplug it from the power outlet. Check for any foreign objects that may be lodged in the sharpening slots. If the problem persists, contact the manufacturer for assistance.
Problem: The sharpener is not turning on.
Solution: Make sure that the sharpener is properly plugged into a power outlet and that the power switch is in the on position. If the problem persists, check the fuse box or contact the manufacturer for assistance.

Pros & Cons

Pros

Easy to use
Versatile and can sharpen any type of scissors
Two-stage sharpening system produces razor-sharp edges
Compact and lightweight design
Safety lock for secure storage

Cons

May be too expensive for some users
May not sharpen serrated blades effectively

Customer Reviews about ScissorPro Electric Scissor Sharpener

Customers have praised the ScissorPro Electric Scissor Sharpener for its ease of use, versatility, and sharpness. Many have noted that it has made sharpening scissors a quick and effortless task, and that the sharpener has prolonged the life of their scissors. However, some have noted that it may not sharpen serrated blades effectively and that it may be too expensive for some users.

Search Manuals in: scissor-500

Read More