Introduction

The Snow Joe SJ618E Electric Snow Thrower is a powerful and efficient tool for clearing snow from walkways, driveways, and decks. This snow thrower is lightweight, easy to maneuver, and can handle up to 18 inches wide and 10 inches deep of snow. It is affordably priced, making it an excellent choice for homeowners who need a reliable snow removal solution. The Snow Joe SJ618E was launched in 2021 and is available for purchase online and in-store.

Accessories

WARNING! ALWAYS use only authorized Snow Joe® + Sun Joe replacement parts and accessories. NEVER use replacement parts or accessories that are not intended for use with this electric snow thrower. Contact Snow Joe + Sun Joe if you are unsure whether it is safe to use a particular replacement part or accessory with your electric snow thrower. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.

Detailed Specifications

Type: Electric Snow Thrower
Brand: Snow Joe
Model: SJ618E
Cord Length: 20 feet
Clearing Width: 18 inches
Clearing Depth: 10 inches
Auger Diameter: 12 inches
Throwing Distance: 25 feet
Speed: 2500 RPM
Weight: 32.4 pounds

Know Your Electric Snow Thrower

Read the owner’s manual and safety rules carefully before operating your electric snow thrower. Compare the illustration below to the actual unit in order to familiarize yourself with the location of the various controls and adjustments.

Handle bar
ON/OFF switch lever
Safety switch button
Extension cord restraint holder
Upper handle
Upper crank rod
Appliance cord
Middle frame
Handle knob (6)
Lower crank rod
Chute deflector
Deflector knob (2)
Lower frame
Discharge chute
Main cover
Auger
Assembly wheel
Side cover
Scraper bar
Cotter pin

Technical Data

Rated Voltage	120 V ~ 60 Hz
Power	13 A
No Load Speed	2000 ± 10% rpm
Rotor	2-blade temp-resistant durable plastic auger
Tire Size	6.3 in. (16 cm)
Type of Snow	Light, fluffy
Clearing Width	18 in. (46 cm)
Depth of Snow Cut	8 in. (20 cm)
Throw Distance	Max 20 ft (6 m)
Plowing Capacity	Max 17.5 tons/hr (15.9 metric tons/hr)
Directional Control	180º adjustable chute
Weight	25.9 lbs (11.75 kg)

Unpacking

Carton Contents

Electric snow thrower with upper handle
Middle frame
Lower frame
Discharge chute
Chute deflector
Upper crank rod
Lower crank rod with cotter pin
Crank rod connector
Handle knobs/deflector knobs (8)
Square J-bolts (2)
Carriage bolts (6)
Thumbscrews (2)
Manual with registration card

Carefully remove the electric snow thrower and check to see that all of the above items are supplied.

Inspect the product carefully to make sure no breakage or damage occurred during shipping. If you find damaged or missing parts, DO NOT return the unit to the store.

NOTE: Do not discard the shipping carton and packaging material until you are ready to use your new electric snow thrower. The packaging is made of recyclable materials. Properly dispose of these materials in accordance with local regulations or save the packaging for long-term product storage.

IMPORTANT! The equipment and packaging material are not toys. Do not let children play with plastic bags, foils, or small parts. These items can be swallowed and pose a suffocation risk!

Assembly

CAUTION m Inspect wiring, which, if damaged during shipping, may cause serious bodily injury during equipment use.

Upper, Middle and Lower Frame Assembly

Align the holes in the upper handle with those in the top of the middle frame (Fig. 1).
Secure the upper handle to the middle frame using 2 knobs and 2 carriage bolts. Install the knobs on the outside of the unit, and tighten (Fig. 2).
Align the holes in the middle frame with those in the top of the lower frame (Fig. 3).
Secure the middle frame to the lower frame using 2 knobs and 2 carriage bolts. Install the knobs on the outside of the unit, and tighten (Fig. 4).
Align the holes in the bottom of the lower frame with those on the unit (Fig. 5).
Secure the lower frame to the unit using 2 knobs and 2 J-bolts. Install the knobs on the inside of the unit, and tighten (Fig. 6).

Chute Crank Assembly

Remove the cotter pin from the lower crank rod (Fig. 7).
Insert the pin-hole end of the lower crank rod into the opening at the back of the housing with holes aligned (Figs. 8 – 10).
Secure the lower crank rod in place with the cotter pin (Figs. 11 – 12).
Slide the crank rod connector over the top of the lower crank rod (Fig. 13).
Align the hole on the bottom of the crank rod connector with the hole in the lower crank rod, insert the first thumbscrew and turn clockwise to secure it (Fig. 14).
Slide the upper crank rod through the rubber ring located on the middle frame (Fig. 15). Slide the upper crank rod into the top of the crank rod connector (Fig. 16).
Align the holes on the connector with the holes in the upper crank rod, insert the second thumbscrew and turn clockwise to secure it (Fig. 17).

Discharge Chute Assembly

Align the lower chute to the slot in the collar, and rotate clockwise to the locked position (Figs 18 – 19).
Secure in place with the provided screw (Fig. 20).
Position the chute deflector over the discharge chute and align the holes (Fig. 21).
Secure the carriage bolts and knobs. Make sure the knobs are tightened (Fig. 22).
Turn the chute control crank clockwise to ensure the discharge chute and deflector are in position.

Description

Snow Joe SJ618E Electric Snow Thrower is a corded electric snow thrower that is easy to start and use. It features a powerful 13.5-amp motor that can quickly clear snow from your driveway, walkway, or deck. The Snow Joe SJ618E has a 18-inch wide and 10-inch deep clearing path that can move up to 650 pounds of snow per minute. It also has a 12-inch diameter auger that can break up compacted snow and ice. The snow thrower has a throwing distance of 25 feet and a discharge chute that rotates 180 degrees, making it easy to direct snow where you want it to go.

Operation

NOTE: Before using this machine, make sure that the power source you will use complies with the specifications detailed in this manual. Before inserting the plug into the socket, verify that the snow thrower’s auger and rubber plates are firmly secured, and that the rubber plates are facing the correct direction. Perform a test run to ensure that the rotor turns freely.

Securing the Extension Cord

For safe and efficient use of your snow thrower, use only a UL-rated extension cord recommended for outdoor use. Refer to the Extension Cord Chart on page 2.
Push a loop of the extension cord through the slot on the cord lock from the opposite side of the restraint hook. Position the loop over the hook and pull the cable back through the slot (Fig. 23).
Insert the female end of the extension cord into the appliance's polarized male plug (Fig. 24).
Note that the snow thrower has a polarized male plug – one prong in the plug is slightly longer and wider than the other (Fig. 25). The extension cord female end should be likewise polarized so that the extension cord fits snugly into the appliance plug.

WARNING

Damaged electrical cords present risk of fire, electrical shock, and serious bodily injury. Before operating the snow thrower, carefully examine the electrical cord. If the cord is damaged, do not use the snow thrower. Replace or repair the damaged cord immediately. If you need assistance, contact an authorized Snow Joe + Sun Joe service center.

Powering On and Off

WARNING! The auger starts rotating immediately after the snow thrower is switched on. Keep hands and feet away from the auger.

To power on, depress and hold the safety switch button found alongside the switch housing (Fig. 26).
While depressing the safety switch button, pull the ON/OFF switch lever toward you. Once the machine powers on, release the safety switch button and begin operation (Fig. 26). The machine can only be started by depressing the safety switch button first, followed by squeezing the ON/OFF switch lever; reverse operation will not start the machine.
To power off, release your grip on the ON/OFF switch lever.

Moving the Machine and Plowing the Snow

WARNING: Foreign objects, such as rocks, broken glass, nails, wire, or string, can be picked up and thrown by the snow thrower, causing serious personal injury. Remove all foreign objects from the area to be plowed before operating the snow thrower.

Keep the area of operation free of foreign objects that can become thrown by the rotor blades. Perform a thorough inspection of the area since some objects may be hidden from view by surrounding snow. If the snow thrower hits an obstruction or picks up a foreign object during use, stop the snow thrower, disconnect the extension cord, remove the obstruction, and inspect the unit for damage. Repair or replace any damaged part before restarting and operating the unit.
Keep children, pets, and bystanders away from the area of operation. Be aware that the normal noise of the machine when turned on may make it difficult for you to hear approaching people.
When moving the snow thrower, use the wheels on one side as the pivot point. Slightly tilt the snow thrower on this pivot point to move it forward or backward.
Start your clearing path near the electrical outlet and work outward, throwing snow in a back and forth motion. To clear in the opposite direction, step over the cord and pivot the snow thrower on its wheels. Make sure to overlap clearing paths.
Note the wind direction. If possible, move in the same direction as the wind so that the snow is not thrown against the wind (and thus back into your face and onto the just-cleared path).
While moving the snow thrower, do not drag the power cable violently or roughly. The snow thrower should move within the range that the cable can safely reach.
Do not push the snow thrower with excessive force. You should push the machine gently and evenly in accordance with the unit’s throw rate.
Do not apply additional man-made load to the engine since this may cause engine damage.
Some parts of the snow thrower may freeze under extreme temperature conditions. Do not attempt to operate the snow thrower with frozen parts. If the parts freeze while the snow thrower is in use, stop the snow thrower, unplug the extension cord, and inspect for frozen parts. Free all parts before restarting or operating the snow thrower. Never force controls that have frozen.
When working on pebbles, gravel, or unpaved surfaces, avoid throwing loose surface material along with the snow by pushing down on the handle to raise the scraper bar at the base of the unit above the pebbles or gravel.
For larger areas, a definite pattern of operation is required to thoroughly clean an area of snow. These patterns will avoid throwing snow in unwanted places, as well as eliminate the need for a second removal of snow (Fig. 27).

Pattern A: Throw the snow to the right or left side where it is possible. For areas such as a long driveway, it is advantageous to start in the middle. Plow from one end to the other, throwing snow to both sides. Pattern B: If the snow can only be thrown to one side of the area to be cleared, start on the opposite side.

Changing Throw Direction and Throw Height

WARNING

Never direct the snow discharge chute at the operator, at bystanders, at vehicles, or at nearby windows. The discharged snow and foreign objects accidentally picked up by the snow thrower can cause serious damage and personal injury. Always orient the discharge chute in the opposite direction from where you, bystanders, surrounding vehicles, or windows are located.

The discharge chute can be adjusted 180 degrees by rotating the chute crank. Rotate the chute control crank clockwise to move the discharge chute to the left and counterclockwise to move the chute to the right (Fig. 28).
The chute deflector on the top of the discharge chute controls the height of the snow stream. Loosen the knobs to raise or lower the deflector to the desired height of snow you wish to throw. Tighten the knobs to secure the deflector (Fig. 29).

WARNING

Make sure that the chute deflector snaps and locks completely onto the discharge chute. An opening between the discharge chute and the chute deflector may allow foreign objects to be picked up by the snow thrower and thrown in the direction of the operator causing serious bodily injury.

Do not advance the chute deflector too far forward causing an opening to appear between the deflector and discharge chute.
Do not overtighten the knobs on the chute deflector.

Maintenance

WARNING

Make sure to turn off the switch and disconnect the extension cord before performing any maintenance task on your snow thrower.

Lifetime Lubrication (Motor and Auger)

Lubrication is not necessary and may damage the unit. The snow thrower is lubricated for lifetime use at the factory before shipment.

General Maintenance Tips

Do not attempt to repair the machine unless you have the proper tools and instructions for disassembly and repair of the machine.
Check bolts and screws at frequent intervals for proper tightness to ensure that the equipment is in safe working condition.
After each snow removal session, run the snow thrower for a few minutes to prevent the collector/impeller from freezing. Shut off the motor, wait for all revolving parts to stop completely, and wipe residual ice and snow off the unit. Rotate the chute crank several times to remove any excess snow.
Only use a cloth soaked with hot water and a soft brush to clean the snow thrower; never wet or spray water on the machine!
Do not use detergent or solvents as these could cause irreparable damage to the snow thrower. Chemicals can destroy the plastic parts.
To protect the snow thrower from corrosion when storing for long periods, lightly oil the metal parts.
Store the appliance in a dry area out of reach of children.
For the user's safety, worn or damaged parts must be replaced. Replace with original replacement parts only. Parts from another snow thrower may not fit properly, causing an unsafe situation.

Replacing the Plastic Auger

NOTE: When replacing worn plastic plates, pay close attention to any different types of bolts and nuts and where they are positioned. This will ensure that the new plastic plates are installed properly and securely.

Open the two side covers by removing the 5 screws on each side (Figs. 30 – 31).
Remove the belt from the drive wheel on the left side (Fig. 32).
Remove the screws and the bushings from the drive wheel (Fig. 33).
Remove the auger axle set (Fig. 34).
Remove the old auger from the housing (Fig. 35).
Install the replacement auger by following the above steps in reverse order.

Replacing the Scraper Bar

The scraper bar is located at the base of the snow thrower beneath the rotor housing (Fig. 36).
Remove the screws that secure the scraper to the snow thrower (Fig. 37).
Install the new scraper bar and fasten it securely to the snow thrower with the screws.

Replacing the Belt

NOTE: Under normal operating conditions, it should not be necessary to replace the auger belt. However, should the auger jam or malfunction, the belt could be damaged. To replace the belt, follow the instructions. NOTE: Determine the left and right hand side of the snow thrower by standing behind the unit in the normal operating position.

Open the left side plate by removing the five screws (Fig. 38).
Use your right hand to turn the rib side of the belt up and pull upwards while turning the auger pulley counterclockwise with your left hand. The belt can be easily removed from the pulley (Fig. 39).
Put the belt on the drive pulley first and then place the belt at the lower end of the auger pulley (Fig. 40).
Use your right hand to press the belt with the ribbed side down. While holding the belt down with your right hand, use your left hand to turn the auger forward so that the auger pulley rotates in a clockwise direction. The belt will be gradually pushed down onto the pulley. When the belt is seated on the pulley, adjust it so that the ribs of the belt match the grooves on the pulley (Fig. 41). After the belt is installed, replace the side plate and secure it with the five screws (Fig. 38).

NOTE: Heavy wet snow puts a load on belts, thus requiring more frequent belt replacement.

Storage

Allow the engine to cool completely before cleaning, storing, or transporting the snow thrower. Be sure to secure the unit while transporting.
Disconnect the extension cord from the snow thrower. Inspect the extension cord closely for signs of wear or damage. Replace it if it is worn or damaged.
Inspect the snow thrower carefully for worn, loose, or damaged parts. Check connections and screws and tighten if necessary.
Store the unit, along with the disconnected extension cord, in a locked, dry place out of the reach of children to prevent unauthorized use or damage. Cover loosely with a tarp for added protection

Setup Guide of Snow Joe SJ618E Electric Snow Thrower

Setting up the Snow Joe SJ618E Electric Snow Thrower is quick and easy. Here are the steps to assemble and operate your snow thrower:

Assemble the Snow Joe SJ618E by attaching the handle to the base of the snow thrower. Use the included tools to tighten the bolts and secure the handle in place.
Plug the snow thrower into a power outlet using the included 20-foot cord. Make sure to use an extension cord rated for outdoor use if you need more length.
Turn on the snow thrower by pressing the start button. The snow thrower will start immediately, and you can begin clearing snow.
Direct the snow thrower toward the snow you want to remove. The adjustable discharge chute makes it easy to control where the snow is thrown.
Steer the snow thrower with the handlebars, and use the auger to break up compacted snow and ice.

Important Safety Instructions

All Operators Must Read These Instructions Before Use

Any electrical appliance can be dangerous if used incorrectly. Some of the safety precautions given in this manual apply generally to many appliances. Other warnings are specific to the use of this snow thrower. Keep this manual for future reference.

General Safety WARNINGS!

You and any other operator of this snow thrower must read, understand, and follow these instructions in their entirety, and should reread them at the start of each snow season. Failure to follow these instructions may result in ELECTRIC SHOCK, FIRE, and/or serious PERSONAL INJURY.

Notice the personal safety alert symbol m used in this manual to draw your attention to a WARNING given along with the particular operating instruction. This means that the operation requires special ATTENTION, CAUTION, and AWARENESS.

Keep work area clean and well lit. Cluttered, dark areas invite accidents.
Do not operate the snow thrower in an explosive atmosphere, such as in the presence of flammable liquids, gases, or dust. Electrical appliances create sparks that may ignite the dust or fumes.
Keep children, pets, and bystanders away from the work area. Be aware that the normal noise of the machine when turned on may make it difficult for you to hear approaching people. Spectators should wear safety glasses and be kept a safe distance away from the work area. Do not let spectators touch the snow thrower or the extension cord.
Electrical plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with grounded appliances. Unmodified plugs and matching outlets will reduce the risk of electric shock.
Avoid body contact with earthed or grounded surfaces (i.e. upper and lower water pipes, radiators, ranges, refrigerators, microwave ovens, and outer frames of heating equipment). Take necessary precautions to avoid electric shock. There is an increased risk of electric shock if your body is earthed or grounded.
Do not abuse the cord. Keep the cord away from heat, oil, sharp edges, or moving parts. Never carry the snow thrower by its cord or yank the cord to disconnect it from the electrical outlet. Damaged or entangled cords increase the risk of electric shock.
Replace or properly repair damaged cords. If the cord becomes damaged in any manner while plugged into the wall receptacle, immediately pull the extension cord plug from the receptacle.
Contact with water while operating the snow thrower can result in electric shock and serious bodily injury. Do not use the snow thrower in damp or wet locations or expose to rain. Do not handle the plug or the appliance with wet hands or while standing in water.
WARNING – Use outdoor extension cords marked SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOWA. These cords are rated for outdoor use and reduce the risk of electric shock.
Turn off the power switch and disconnect the power cable before making any adjustments to the unit and before inspecting, servicing, changing accessories, or cleaning the snow thrower. Follow the same procedure if any other dangerous conditions are present during operation. Any adjustments to the unit should be performed after revolving parts inside the snow thrower stop completely. Such preventative safety measures reduce the risk of starting the power tool accidentally.
If you find the main power cable or the extension cable damaged, please pull out the plug from the socket and disconnect the power immediately. Repair the cable or replace it if necessary.
When replacing any parts, you must strictly observe the instructions and procedures described in this operator's manual. Special care should be paid to any rubber parts, since these parts may increase the engine load and decrease its mechanical power if damaged.
Do not move or transport the snow thrower when the plug is connected to the power socket and the switch is turned on.
If, during use, you notice that the unit runs unstably or hear abnormal sounds from the engine, stop the machine, disconnect the power immediately and contact an authorized Snow Joe + Sun Joe service center.

Electrical Safety

Ground fault circuit interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for the snow thrower. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.
To prevent electric shock, use only with an extension cord suitable for outdoor use, such as SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A. Before use, check that the extension cord is in good condition. When using an extension cord, make sure to use one heavy enough to carry the current your product will draw. For lengths less than 50 ft (15 m), a No.14 AWG (or greater) extension cord should be used. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
To reduce the risk of electric shock, this appliance has a polarized plug (i.e. one blade is wider than the other). Use this appliance only with a polarized UL-, CSA-, or ETL-rated extension cord for outdoor, all-weather use. The appliance plug will fit into a polarized extension cord only one way. If the appliance plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension cord will require the use of a polarized wall outlet. The extension cord plug will fit into the polarized wall outlet only one way. If the plug does not fit fully into the wall outlet, reverse the plug. If the plug still does not fit, contact a qualified electrician to install the proper wall outlet. Do not modify the appliance plug, extension cord receptacle, or extension cord plug in any way.

WARNING

Electric shock may cause SEVERE INJURY or DEATH. Heed these warnings:

Do not allow any part of the snow thrower to make contact with water while it is in operation. If the appliance becomes wet while turned off, wipe dry before starting.
Use only a UL-, CSA-, or ETL-rated extension cord for outdoor, all-weather use, such as the Snow Joe®+ Sun Joe® SJTW-A 14-gauge 50-foot extension cord with lighted end (Model PJEXT50-B). Visit snowjoe.com to purchase this extension cord online or, to order by phone, call 1-866-SNOWJOE (1-866-766-9563).
Do not use an extension cord over 100 ft (30 m).
Do not touch the appliance or its plug with wet hands or while standing in water. Wearing rubber boots offers some protection.

EXTENSION CORD CHART

Extension Cord Length	Wire Gauge (A.W.G.)
Up to 50 ft (15 m)	14
+50 ft - 100 ft (+15 m - 30 m)	12

To prevent the appliance cord from disconnecting from the extension cord during operation, use the on-board cord restraint hook and/or make a knot with the two cords as shown in Table 1.

Personal Safety

Stay alert – Watch what you are doing and use common sense when operating the snow thrower. Do not use the machine when tired, ill, or under the influence of drugs, alcohol, or medication. A moment of inattention may result in serious personal injury.
Wear proper clothing – Wearing rubber boots offers additional protection from electric shock. Do not wear loose clothing or jewelry that may become caught in the machine. Wear protective headgear to keep hair away from revolving parts of the machine. Safety glasses offer better protection than everyday eyeglasses.
Moving parts present risks – Keep your face, hair, clothing, hands, and feet away from moving parts. All guards and safety attachments must be installed properly before using the unit. Shut off and disconnect the cord before touching any parts other than the handles and the switch.
Surfaces – This snow thrower is intended for use on paved surfaces. Do not use on gravel, stone, or other unpaved surfaces unless the snow thrower is adjusted for such surfaces according to the instructions given in this operator’s manual.
Avoid accidental starting – Make sure the switch is in the off position before plugging in the unit. Do not carry the snow thrower with your finger on the switch.
Body position – Maintain proper footing and balance at all times. Place heels firmly on the ground and tightly grasp the handle bar. Watch for uneven surfaces and do not overreach. In case you fall or collide with the snow thrower, inspect the unit for any damages or cracks. When stepping backwards, be careful to avoid obstacles beneath your feet or behind you to avoid falling.
If the snow thrower strikes any object, immediately stop the snow thrower, then inspect for damage – Repair any damage before restarting and operating the snow thrower.

Safety Instructions for Walk-Behind Snow Throwers

Read the operator’s manual carefully – Learn your snow thrower’s applications and limitations as well as the specific potential hazards related to this machine. Do not use this machine for any purpose other than the one for which it was designed. Otherwise, it may cause mechanical defects, serious damage, or personal injury.
Preliminary unit inspection – Thoroughly inspect the unit before use. Make sure all the parts are secure and installed correctly. If you notice any abnormalities, do not use the machine until it has been properly repaired. Always perform a test run the first time you use the snow thrower or after replacing parts to ensure that the unit is functioning properly.
Preliminary area inspection – Clear the area to be plowed before each use. Remove all objects, such as rocks, broken glass, nails, wire, or string, which can be thrown by or become entangled in the snow thrower. Keep the area of operation clear of all spectators, particularly children and pets.
Excessive force – The snow thrower was designed to respond at a certain rate for various snow conditions for optimum safety and performance. Do not force it; keep pressure constant.
Malfunctioning switch – Do not use the snow thrower if the switch does not turn it on and off. Any electrical appliance that cannot be controlled by the switch is not safe to use and must be repaired.
Hitting an object – If the snow thrower accidentally strikes an object, follow these steps: i) Stop the snow thrower and unplug the unit ii) Inspect for damage iii) Repair or replace any damaged part before restarting and operating the snow thrower.
Discharge chute safety – Never direct the snow discharge chute at the operator, at bystanders, at vehicles, or at windows. The discharged snow stream and foreign objects accidentally picked up by the snow thrower can cause serious damage and personal injury. Do not use your hands to unclog the discharge chute. Stop the motor before removing debris.
Hand-held operating position – Operation of the snow thrower in the hand-held position is unsafe.
Abnormal operation – If you notice the snow thrower running in an unstable state or hear abnormal sounds from the engine, immediately stop the machine, disconnect the power, and contact an authorized Snow Joe® + Sun Joe® service center.
Noise control – When using the snow thrower, you must respect local laws and regulations regarding noise control and environmental protection. To avoid noise disturbance, you should carefully decide upon an appropriate operation time and consider the surrounding conditions.
When work is completed – Disconnect the snow thrower from the power source when not in use, when changing accessories, and before performing any maintenance function.
Store safely – Store the snow thrower indoors in a dry area between uses. Keep it in a locked area, where children and unauthorized users cannot gain access. Do not store the machine while it is still connected to the power source as this may result in damage and injury.
Maintain for safety and longevity – Check for misalignment or binding of moving parts, breakage of parts, and any other conditions that may affect the unit’s operation. If damaged, repair or replace the damaged part before use. Use only original replacement parts designed specifically for your model. When replacing any parts, you must strictly observe the instructions and procedures described in this manual. Special care should be paid to any rubber parts, since these parts may increase the engine load and decrease its mechanical power if damaged.
Always check that all bolts, nuts, and knobs are tight before using the snow thrower

Safety Symbols

The following table describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate.

Snow Joe SJ618E Electric Snow Thrower Troubleshooting

Here are some common problems and solutions for the Snow Joe SJ618E Electric Snow Thrower:

The snow thrower won't start: Check that the power cord is properly plugged in and the outlet is working. Make sure that the auger is not obstructed by debris or snow.
The snow thrower is not throwing snow: Check that the snow is not too heavy or wet, and adjust the discharge chute if necessary. Make sure that the auger is turning properly.
The snow thrower is vibrating excessively: Check that all bolts and screws are tight and secure. Make sure that the snow thrower is on a flat and even surface.

Warranty

OUR PROMISE: Snow Joe + Sun Joe warrant new products for two years from the date of purchase

WHO CAN SEEK WARRANTY COVERAGE?
This Warranty is extended by Snow Joe + Sun Joe to the owner of this Machine (a “Machine” consists of a product powered by a motor) for residential and personal household use only. This Warranty does not apply to products used for commercial, rental or re-sale purposes. Should ownership of this machine change during the 2-year period, please update the Machine’s owner information at https://snowjoe.com/register-product

WHAT IS COVERED?

Snow Joe + Sun Joe warrants to the owner that if this Machine fails within 2 years from the date of purchase due to a defect in material or workmanship or as a result of normal wear and tear from ordinary household use, Snow Joe® + Sun Joe® will send a replacement part or product, as needed, free of charge and with free shipping to the original purchaser.

Pros & Cons

Pros

Affordable price
Easy to use and maneuver
Powerful motor can handle heavy snow
Adjustable discharge chute
Lightweight and compact

Cons

Requires a power outlet
Not suitable for large areas or deep snow
Short cord length
Not self-propelled

Search Manuals in: thrower

Read More