Trendnet 10-Port NWay Gigabit Switch TEG-S28TX User Manual

Content

Introduction to the TRENDnet 10-Port NWay Gigabit Switch TEG-S28TX

The TRENDnet 10-Port NWay Gigabit Switch TEG-S28TX is a wired Ethernet switch designed to expand a home, small-office, laboratory, or workgroup network with dependable 10/100/1000 Mbps connectivity. It provides ten copper Ethernet ports for connecting computers, printers, servers, network-attached storage devices, wireless access points, and additional switches through standard twisted-pair cabling.

Using IEEE 802.3 NWay auto-negotiation, the switch automatically detects compatible speed and duplex settings on each connected device. Gigabit-capable equipment can communicate at up to 1000 Mbps per port, while older 10 Mbps and 100 Mbps devices remain supported. This makes the unit useful when upgrading a mixed network without replacing every existing adapter or cable.

The TEG-S28TX is an unmanaged switch, so it is intended for straightforward plug-and-play installation rather than advanced VLAN, routing, or traffic-monitoring tasks. Its internal power supply and compact desktop-oriented design make it suitable for offices, wiring closets, classrooms, and test benches where additional Ethernet ports are required.

This guide explains the switch’s supported standards, connection procedure, basic network design considerations, troubleshooting methods, and practical limitations. Because the model has been discontinued, replacement planning and compatibility checks are especially important for long-term deployments.

TRENDnet TEG-S28TX Specifications and Features

Product type: Unmanaged 10-port copper Gigabit Ethernet switch.
Network standards: IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T, IEEE 802.3 NWay auto-negotiation, and IEEE 802.3x flow control.
Ports: Ten RJ-45 Ethernet ports supporting 10 Mbps, 100 Mbps, and 1000 Mbps connections.
Gigabit performance: Up to 1000 Mbps in each direction per full-duplex Gigabit port, with a theoretical 2000 Mbps full-duplex transfer rate.
Fast Ethernet performance: Up to 100 Mbps half-duplex or 200 Mbps full-duplex.
Ethernet performance: Up to 10 Mbps half-duplex or 20 Mbps full-duplex.
Switching method: NWay auto-negotiation and standard Ethernet switching for automatic connection compatibility.
Data buffer: 256 KB per device.
Maximum cable distance: Up to 100 meters per copper Ethernet segment when suitable cabling and installation practices are used.
Supported topology: Star topology, with the switch positioned as a central connection point.
Network protocol: CSMA/CD Ethernet operation.
Power: Internal universal switching power supply rated for 100–240 VAC, 50/60 Hz.

How to Set Up the TRENDnet 10-Port NWay Gigabit Switch TEG-S28TX

Place the switch on a stable, dry, well-ventilated surface. Leave clearance around the enclosure so heat can escape.
Connect the supplied power cord to the switch and then to a properly grounded electrical outlet. Do not use a damaged cord or operate the unit near water.
Connect one Ethernet cable from a router, gateway, or upstream switch to any available RJ-45 port.
Connect computers, printers, servers, access points, or other network devices to the remaining ports. Use four-pair Category 5 or better cabling for Gigabit operation.
Allow the switch and connected devices to negotiate link speed automatically. No IP address, web interface, login, or software configuration is required for basic operation.
Check the port indicators. A link light normally confirms physical connectivity, while activity indications show network traffic.

For best results, keep each copper cable within the 100-meter limit and avoid running Ethernet cables parallel to high-voltage power wiring. If a device does not connect, test another cable and switch port, confirm that its network adapter is enabled, and temporarily connect it directly to the router. The switch does not provide wireless networking, Power over Ethernet, routing, VLAN configuration, or managed quality-of-service controls.

TRENDnet TEG-S28TX Troubleshooting Guide

No power or status lights

Confirm that the power cord is firmly connected at both ends and that the outlet works with another appliance. Disconnect the switch before inspecting the cord. Do not open the enclosure; internal power components should be serviced only by qualified personnel.

No link on one port

Replace the Ethernet cable with a known-good cable, reconnect both ends, and try a different switch port. Inspect the connector for bent contacts or damage. Verify that the connected computer, printer, or access point is powered on and that its Ethernet adapter is enabled.

Connection operates at 100 Mbps instead of Gigabit

Gigabit Ethernet requires all four twisted pairs and suitable cabling. Replace older or damaged cables, check the device’s network-adapter settings, and remove intermediate couplers. A 10/100-only device will correctly remain at its lower negotiated speed.

Intermittent connectivity

Check for loose connectors, excessive cable length, electrical interference, overheating, or a failing network adapter. Improve ventilation and test devices individually to isolate the affected cable or port.

Support and replacement planning

The TEG-S28TX is discontinued, and its official support resources include legacy documentation. Consult TRENDnet’s support pages for the archived user guide, technical documentation, warranty eligibility, and current contact channels. Because support coverage can depend on purchase date and warranty status, keep the model and hardware version available when requesting assistance.

Pros and Cons of the TRENDnet TEG-S28TX

Advantages

Ten network ports: Provides more connections than common five-port desktop switches, helping link several computers and peripherals without immediately adding another switch.
Gigabit capability: Supports up to 1000 Mbps connections for compatible devices, making it suitable for local file transfers, server access, and network storage.
Broad device compatibility: Automatic negotiation supports legacy 10 Mbps and 100 Mbps equipment alongside Gigabit hardware.
Simple installation: As an unmanaged switch, it needs no software, IP configuration, administrator account, or ongoing configuration.
Standard copper connectivity: Works with conventional RJ-45 Ethernet cabling and supports cable runs up to 100 meters under appropriate conditions.
Universal power input: The 100–240 VAC, 50/60 Hz internal supply supports common electrical systems.

Limitations

No management features: It does not provide VLANs, port mirroring, link aggregation, traffic statistics, advanced QoS, or remote administration.
No PoE: It cannot supply power to cameras, access points, or VoIP phones through Ethernet.
No routing: A separate router or gateway is required for Internet access, DHCP, firewall functions, and communication between IP networks.
Legacy product: Its discontinued status may make replacement parts, current documentation, and long-term support less predictable.
Best for basic networks: Choose a newer managed, PoE, or higher-capacity switch if the installation needs centralized administration, powered devices, segmentation, or modern monitoring features.

PDF

Faqs

How do I set up the trendnet 10-Port NWay Gigabit Switch TEG-S28TX for the first time?

Place the trendnet 10-Port NWay Gigabit Switch TEG-S28TX in a ventilated location and connect its power cable. Use Ethernet cables to connect computers, access points, printers, servers, or other network devices to the switch, then connect one port to your router or existing network. The switch is unmanaged, so no IP address or web configuration is normally required. Link activity should appear on the corresponding port LEDs after devices are powered on.

Why is the trendnet 10-Port NWay Gigabit Switch TEG-S28TX not providing a network connection?

Check that the switch power light is on and that both ends of each Ethernet cable are firmly connected. Replace the cable if the port LED remains off, then test the device on another switch port. Confirm that the router or upstream switch is operating normally and that the computer is configured to obtain an IP address automatically. Restarting the router, switch, and connected device can also clear a temporary link or address-assignment problem.

Can I use Gigabit Ethernet cables with the trendnet 10-Port NWay Gigabit Switch TEG-S28TX?

Yes. For reliable 1000 Mbps connections, use four-pair Cat 5 or better twisted-pair Ethernet cable, preferably Cat 5e or Cat 6. Keep each copper cable run within the normal 100-meter maximum, including patch leads where practical. Damaged, incorrectly terminated, or older two-pair cables may force a connection to 10 or 100 Mbps. Replace suspect cables and check whether the port indicator changes after reconnecting.

Which ports should I use for the fastest connections on the trendnet 10-Port NWay Gigabit Switch TEG-S28TX?

The TEG-S28TX combines eight 10/100 Mbps Fast Ethernet ports with two 10/100/1000 Mbps Gigabit Ethernet ports. Connect bandwidth-heavy devices such as file servers, network-attached storage, or an uplink to another Gigabit switch to the Gigabit-capable ports. Ordinary computers, printers, and older network equipment can use the remaining ports. The connected device and cable must also support Gigabit Ethernet for a 1000 Mbps link.

Does the trendnet 10-Port NWay Gigabit Switch TEG-S28TX require manual speed or duplex configuration?

Usually not. NWay auto-negotiation allows the trendnet 10-Port NWay Gigabit Switch TEG-S28TX to detect compatible link speed and duplex settings automatically. Leave connected network adapters set to Auto Negotiation unless a specific legacy device requires another setting. If a link repeatedly drops or operates at the wrong speed, update the device driver, replace the Ethernet cable, and check the far-end port before changing adapter settings.

How can I improve file-transfer performance through the trendnet 10-Port NWay Gigabit Switch TEG-S28TX?

Connect the server, storage device, and high-traffic uplink to the two Gigabit ports whenever possible. Use Cat 5e or Cat 6 cable, keep runs below 100 meters, and avoid damaged connectors or unnecessary couplers. Remember that the eight Fast Ethernet ports cannot exceed 100 Mbps link speed. Actual file-transfer performance also depends on the computers, storage drives, router, network protocol, and simultaneous traffic, not only the switch.

Can the trendnet 10-Port NWay Gigabit Switch TEG-S28TX power devices through Ethernet?

Do not assume that the trendnet 10-Port NWay Gigabit Switch TEG-S28TX supports Power over Ethernet. Treat it as a standard Ethernet switch and use separate power adapters for wireless access points, cameras, VoIP phones, or other powered devices unless their documentation confirms another power method. If PoE is required, connect a compatible PoE switch or injector between the device and the TEG-S28TX.

How should I maintain and safely use the trendnet 10-Port NWay Gigabit Switch TEG-S28TX?

Keep the switch dry, dust-free, and unobstructed so air can circulate around its vents. Do not place it on top of heat-producing equipment, and avoid tightly bending or pinching Ethernet cables. Before cleaning, disconnect power and wipe the enclosure with a dry, lint-free cloth; never spray liquid into the switch. Periodically inspect cables, connectors, and port LEDs for damage or unusual behavior, and replace faulty cables promptly.