Introduction of Bissell Powerbrush Pet Deep Cleaner 2085

The Bissell Powerbrush Pet Deep Cleaner 2085 is a powerful carpet cleaning machine designed to tackle tough pet stains and odors. This deep cleaner is available for an estimated price of $199.99 and was launched in 2016. The Powerbrush Pet Deep Cleaner 2085 combines powerful suction with a rotating DirtLifter PowerBrush to remove embedded dirt and stains, leaving your carpets looking and smelling fresh.

What’s In The Box?

NOTE: Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the carton top flap.

Getting to Know Your Deep Cleaner

Detailed Specifications

The Bissell Powerbrush Pet Deep Cleaner 2085 comes with the following key features:

• 2-in-1 tank system with 1-gallon capacity
• Rotating DirtLifter PowerBrush
• Powerful suction with 6 amps of motor power
• Collapsible handle for easy storage
• Built-in heater for faster drying times
• 6-inch Tough Stain Tool for upholstery and stairs
• 15-foot power cord
• Weighs 16.5 pounds
• 2-year limited warranty

Bissell Powerbrush Pet Deep Cleaner 2085 Assembly

WARNING
Do not plug in your deep cleaner until you are familiar with all instructions and operating procedures.

The only tool you will need to assemble your cleaner is a Phillips screwdriver.

1. Slide upper body onto lower body.
2. Secure with screws.

3. Slide upper Handle Post into the body by aligning the pin and sliding the Post down into place.

   

4. Be sure to secure upper handle before lifting. Rotate lock collar to secure.
5. Place Clean Water Tank on back of unit. The tank will make a “CLICK” noise when seated properly.

6. Wrap power cord. 

   

Tips Before Carpet Cleaning

• If cleaning an entire room, consider moving your furniture to another area.

• Use a dry vacuum cleaner over area before using your deep cleaner.

• Remove any large, solid debris before wet cleaning.

• Pre-treat stains with BISSELL PreTreat to improve performance on coffee stains and ground-in dirt.

Fill Clean Water Tank

1. Remove the clean water tank lifting straight up and away from lower body.

2. Unscrew the cap at the bottom of the clean water tank.

3. Fill with warm tap water to the WATER line. Fill the rest of the tank with BISSELL Formula to the FORMULA line. 

4. Replace and tighten the cap, then return the clean water tank to lower body. The tank will make a  “CLICK” noise when seated properly.

   

A few notes about filling the clean water tank:

• Fill with hot (140°F/60°C MAX) tap water and add the appropriate BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER OR TAN IN THE MICROWAVE.

NOTICE: Do not over wet carpet. Be careful not to run over loose objects or edges of area rugs. Stalling the brush may result in premature belt failure.
NOTE: Do not substitute BISSELL 2X Formula cleaning solution with other household cleaning products.

Pour in more power with BISSELL Boosts

• Fill tank with water and 2X formula (Step 3 above).

• Add 1 ounce of any BISSELL Boost per 1/2 gallon of water.

• The 2085 machine series have 1/2 gallon clean water tanks.

  

Cleaning Your Carpet

Important! Please check manufacturer’s tag before cleaning area rugs for any specialized cleaning instructions. We do not recommend deep cleaning delicate, silk, wool, antique or area rugs without a manufacturer’s tag.

1. Plug into a proper outlet.

2. Extend the Collapsible Handle Post by turning the collar counterclockwise and lifting the handle up. Turn the collar clockwise to secure.  

   

   IMPORTANT BEFORE USE: Make sure the handle post is fully extended up and the collar lines up with the lock symbol before you begin cleaning.

3. With foot, press the grey recline lever located next to power button.

4. With foot, press the red power button,  located on the back of the machine. 

   

5. Cleaning Pass

   • While pressing the trigger, make one slow forward wet pass and another one back.
   • Release the trigger and make one slow forward and backward pass over the same area.
   • Repeat steps 1 and 2 until solution being pulled up appears clean.

   • Empty the collection tank when dirty water reaches the full line, and fill with fresh warm water and formula when the Clean Water Tank is empty.

     

Empty Collection Tank

WARNING
To reduce the risk of fire, electric shock or injury, turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting.

1. With foot, press the red power button, to turn off unit and then unplug. 

2. Release Collection Tank latches (on each side) by pulling up from the bottom of latch and then out. 

   

3. Carefully remove tank by lifting up on the tank carry handle. 

4. Carry the Collection Tank to a toilet or sink. To empty, pour out contents using opening at back of tank.

   

5. Rinse the Collection Tank thoroughly and replace on unit. Secure latches on both sides of the tank.

6. Refill the Clean Water Tank and continue cleaning or if you’re done cleaning, wait for the pieces to dry before storing your machine.

   

Cleaning Machine After Use

WARNING
To reduce the risk of electric shock, turn power switch OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

1. Unplug the unit.

2. Remove and rinse the Collection Tank thoroughly.

   

3. Remove tank vent & foam filter (located on top of the Collection Tank) and rinse.

4. To remove and clean the nozzle, keep the Collection Tank off of the unit.
   Gently pull the two tabs that point up near the front of the unit. The nozzle will unhook to remove. Rinse under running water. When finished, slightly tilt the machine so the foot raises up so you can align the nozzle hooks at the floor of the unit. Rotate the nozzle up to clip back into place.

   

5. Remove lint and hair from red gasket in base of unit. (Do not remove gasket)

6. Once the parts have been rinsed clean and dried, replace the Collection Tank to the base of the machine and secure with both latches. Wrap power cord around Quick Release Cord Wrap™ on side of the machine. Wipe all surfaces with a soft cloth and store cleaner upright in a protected, dry area.

   

NOTICE: To reduce the risk of a leaking condition, do not store unit where freezing may occur. Damage to internal components may result.

Replacing Belts & Brush Rolls

WARNING
To reduce the risk of electric shock, turn power switch OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

What you will need: 1 Phillips screwdriver & 1 flathead screwdriver

1. Turn the machine off and unplug from wall outlet.

2. Remove the Clean Water and Collection Tanks.

   

3. Lay machine down to access the bottom of the machine. With a Phillips head screwdriver, unscrew the belt cover and remove.

   

4. If you want to replace or clean the brush roll, remove the belt by slightly lifting the brush roll to maneuver the belt and remove it. If the belt is broken and needs to be replaced, remove it and replace with a new belt.

5. When removing the brush roll, the brush roll cap will come with it. Do not lose this part.

   

6. Clean or replace the brush roll and belt. When finished cleaning these parts, reassemble them to the machine.
   Insert the brush into the right side end cap. Adjust the right side of the brush into place and tuck the left brush roll cap (separate piece that attaches to brush roll) into place.

   

7. Maneuver the belt to wrap around the pulley. Wrap the belt around the cog of the brush roll. Secure the brush roll into place by sliding the square piece to align the brush roll.

8. Reattach belt cover and screw into place.

   

NOTE: Manually rotate brush to make sure it rotates freely and the belt is aligned.

HARD FLOOR TOOL SOLD SEPARATELY

Hard Floor Cleaning (select models only)

1. With foot, press the red power button, to turn off unit and then unplug. 

2. Remove the clean water tank lifting straight up and away from lower body.

   

3. Release Collection Tank latches (on each side) by pulling up from the bottom of latch and then out. 

4. Attach the hard floor tool by hooking it into the front of the nozzle. Rotate down until it snaps into place.

   

5. Return both tanks to the machine and plug into a proper outlet.

6. Follow the “Cleaning Pass” instructions on the previous page 

   

WARNING
To reduce the risk of fire and electric shock when cleaning a hard floor, the BISSELL hard floor tool must be used and it must only be used with BISSELL 2X Hard Floor Solutions cleaning fluid intended for use with this appliance.

Description of Bissell Powerbrush Pet 

The Bissell Powerbrush Pet Deep Cleaner 2085 is a versatile and powerful cleaning solution for pet owners. Its unique Dirt Lifter Power Brush rotates deep into carpets to loosen and lift dirt, while the powerful suction removes the dirt and dries the carpet. The large 1-gallon tank system makes it easy to clean large areas without frequent refills, and the collapsible handle saves space for storage. The built-in heater helps speed up drying times, making it perfect for quick cleanup after pet accidents. The 6-inch Tough Stain Tool is ideal for upholstery and stairs, making it a great all-around cleaning solution for pet owners.

Deep Cleaner 2085 Setup Guide

To set up the Bissell Powerbrush Pet Deep Cleaner 2085, follow these simple steps:

1. Remove the packaging and fill the tank with warm water and cleaning solution.
2. Attach the hose and power cord to the machine.
3. Press the power button to turn on the machine and select the desired cleaning mode.
4. Slowly move the machine back and forth over the carpet, making sure to overlap each stroke for complete coverage.
5. Empty the tank and rinse with clean water after each use.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER.
When using an electrical appliance, basic precautions should be observed, including the following:

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY

• Connect to a properly grounded outlet only. See grounding instructions. Do not modify the 3-prong grounded plug.

• Do not leave appliance when it is plugged in. Unplug from outlet when not in use and before servicing.

• Use indoors only.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• Do not use for any purpose other than described in this User’s Guide. Use only manufacturer’s recommended attachments.

• Do not use with damaged cord or plug. If appliance is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.

• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not handle plug or appliance with wet hands.

• Do not put any object into open-ings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• Turn off all controls before plug-ging or unplugging appliance.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.)

•  use in areas where they may be present.

• Do not use appliance in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.

• Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).

• Do not pick up anything that is burning or smoking, such as cig-arettes, matches, or hot ashes.

• Use only BISSELL cleaning products intended for use with this appliance to prevent internal component damage. See the Cleaning Fluid section of this guide.

• Do not immerse. Use only on surfaces moistened by the cleaning process.

• Keep appliance on a level surface.

• Do not carry the appliance while in use.

SAVE THESE INSTRUCTIONS FOR FUTURE USE
This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.

WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you aren’t sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the illustration. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used with this appliance.

GROUNDING INSTRUCTIONS

This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Thanks for buying a BISSELL deep cleaner!
We love to clean and we’re excited to share one of our innovative products with you. We want to make sure your deep cleaner works as well in one year as it does today, so this guide has tips on using (pages 6-8), maintaining (pages 9-12), and if there is a problem, troubleshooting (page 14). In just a few simple assembly steps, you’ll be ready to deep clean. Flip to page 6 and let’s get started!

Cleaning Formulas pf Bissell Powerbrush Pet Deep Cleaner 2085

WARNING
To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning fluids intended for use with the deep cleaner.

Keep plenty of genuine BISSELL formula on hand so you can clean and protect whenever it fits your schedule.

Always use genuine BISSELL deep cleaning formulas. Non-BISSELL cleaning solutions may harm the machine and may void the warranty.

ONLY BISSELL Protects from future stains with Scotchgard™ Protector. Scotchgard™ is a trademark of 3M®. *2.5 fl. oz. of 2X concentrated formula is equivalent to 5.0 fl. oz. of non-concentrated formula.

NOTICE: Use of cleaning formulas that contain lemon or pine oil may damage this appliance and void the warranty. Chemical spot cleaners or solvent-based soil removers also should not be used. These products may react with the plastic materials used in your cleaner, causing cracking or pitting.

Troubleshooting

Here are some common problems and solutions for the Bissell Powerbrush Pet Deep Cleaner 2085:

Bissell Warranty

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Care by e-mail or telephone as described below.

One-Year 
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part. 

Pros & Cons about Bissell Powerbrush Pet Deep Cleaner 2085

Pros

• Powerful suction and rotating brush roll
• Collapsible handle for easy storage
• Built-in heater for faster drying times
• Large tank system for less frequent refills

Cons

1. Stubborn stains may need additional attention before machine cleaning.

2. Could be hard to maneuver, especially when filled.

3. Requires regular cleaning to maintain performance.

4. The reach may be limited for stairs and tight spaces.