Introducing the Coralife Super Skimmers

Coralife Super Skimmers are high-performance protein skimmers designed for aquariums up to 250 gallons. These skimmers are equipped with a unique collection cup and adjustable gate valve, making maintenance a breeze. The estimated price for the Coralife Super Skimmer is around $200, and it's currently available for purchase online and in-store.

Detailed Specifications

Coralife Super Skimmers boast a variety of key features, including:

• Advanced dual-injector pump for maximum foam production
• Adjustable gate valve to fine-tune water level and flow rate
• Unique collection cup design with drain plug for easy cleaning
• Durable construction with high-quality materials for long-lasting use
• Quiet operation for peaceful aquarium environment

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS
CAUTION: To guard against injury, basic safety precautions should be observed when operating the unit.
WARNING

1. Never connect the Coralife Super Skimmer to any power source while hands are wet.
2. Always unplug the unit from outlet or power source before installing, replacing parts or doing product maintenance.
3. Never allow pump to run dry. Always keep pump submerged during operation. Failure to keep pump submerged while in use may damage the unit and/or cause unit failure.
4. Always leave a drip-loop in the pump cord to prevent water from running down the length of the cord and reaching the power source or outlet.
5. For added safety, the pump should be plugged into a grounded three-prong receptacle controlled by a GFI (Ground Fault Interrupter) circuit breaker.
6. Make sure that the Super Skimmer is securely installed before operating.

PRE-INSTALLATION SETUP

NOTE: Prepare at least 5 gallons of “make-up water” to replace water used by the Super Skimmer. (P2)

HANG-ON TANK MOUNT PLACEMENT

1. Allow a minimum 8" clearance between the aquarium and the wall. NOTE: Hang-on tank mounting bracket for up to 1.125" tank mouldings.
2. Ensure that there is adequate unobstructed space for the pump inside the aquarium (9"L x 4"W x 5"H).

SUMP HOOK-UP PLACEMENT

1. Verify that there is adequate space for the super skimmer in/or outside of the sump (12"L x 10"W).
2. Allow a minimum 1" clearance between the underside of the stand and the top of the skimmer. Make sure there is enough space to remove/slide the collection cup out of the sump.

Coralife Parts Diagram

INSTALLATION SETUP

BUBBLE-PRODUCTION DIFFUSER SETUP (Model 65 only)

1. Load fi lter pad (white) into bubble-production diffuser. (2.0)
2. Place sponge (black) on top of fi lter pad (white).
3. Insert mounting bracket into the slot located at the back of the bubble-production diffuser.

NOTE: Identify the type of molding on aquarium or sump and select the correct mounting bracket. (2.1)

COLLECTION CUP SETUP (Model 65 only)

1. Place o-ring into o-ring groove in top opening of main chamber.
2. Align collection cup threaded ring with the top opening on main chamber.
3. Twist collection cup threaded ring clockwise and tighten. Make sure that the connection is secure between both the collection cup and main chamber.

COLLECTION CUP SETUP (Model 125 & 220 only)

1. Attach the collection cup lid to collection cup. (2.2)

2. Attach collection cup drain plug onto collection cup drain or attach collection cup tubing for an optional drain line.
   NOTE: Collection cup drain line prevents overfl ow when attached to a large capacity receptacle.

   

3. Place o-ring into o-ring groove in top opening of main chamber.
4. Align collection cup threaded ring with the top opening on main chamber.
5. Twist collection cup threaded ring clockwise and tighten. Make sure that the connection is secure between both the collection cup and main chamber.

HANG-ON MOUNT INSTALLATION SETUP

NOTE: Saltwater may need to be added to the aquarium to replace water used by the super skimmer.

1. Locate desired area to place skimmer.
2. Attach short fl exible tubing onto chamber intake. (3.0)
3. Attach water pump (with Flow Control Valve on Model 65) to fl exible tubing.
   NOTE: Make sure all tubing connections are secured.
4. Hang main chamber skimmer bracket at desired location on aquarium.
   WARNING: Do not submerse in water or obstruct airway passage through air-inlet silencer.
5. Attach output tubing onto water output with vent hole facing up. (3.1)
   Attach bubble-production diffuser onto aquarium. (3.2)
   NOTE: Adjust bubble-production diffuser mounting bracket. Top of bubble-production diffuser must be .25" min. above water line.
6. Insert the output tubing into bubble-production diffuser sponge (black). (3.2)
   NOTE: Trim output tubing or adjust bubble-production diffuser height to allow a 1" min. space inside the sponge (black) to prevent micro-bubbles.
7. Tighten screws on main chamber skimmer bracket and bubble-production diffuser bracket.

IN-SUMP INSTALLATION SETUP

NOTE: Saltwater may need to be added to the aquarium to replace water used by the Super Skimmer.

1. Locate desired area to place skimmer.
2. Attach long fl exible tubing onto chamber intake. (4.0)
3. Attach water pump (650 - 750 gph) to fl exible tubing.
   NOTE: Make sure all tubing connections are secured.
4. Place Super Skimmer inside/outside sump at desired location.
   NOTE: Add saltwater to skimmer to prevent from fl oating in the sump.
   WARNING: Do not submerse in water or obstruct airway passage through air-inlet silencer.
5. Attach output tubing onto water output with vent hole facing up. (4.1)
6. Place round diffuser sponge into sump. (4.2)

Coralife Super Skimmer Description

Coralife Super Skimmers are designed to provide efficient and reliable protein skimming for aquariums. The dual-injector pump creates maximum foam production, effectively removing organic compounds and waste from the water. The adjustable gate valve allows for easy fine-tuning of the water level and flow rate, ensuring optimal skimming performance. The unique collection cup design features a drain plug for quick and easy cleaning, making maintenance a breeze. With its durable construction and quiet operation, the Coralife Super Skimmer is a must-have for any aquarium enthusiast.

Operations

PRE-OPERATION

1. Make sure that all tubing connections are tightly secured.
2. Verify that collection cup and lid are tightly fastened and sealed to the main chamber.
3. Make sure that the air-inlet silencer is above the water.
   NOTE: Do not obstruct air fl ow into air-inlet silencer.
4. Check water-level adjustment dial and make sure it is in the open position. (5.0)

INITIAL OPERATION

1. Plug water pump (650 - 750 gph) into an outlet or power source.
   NOTE: Inspect connections for leaks and make sure that the water is fl owing through the unit.
2. Adjust water-level adjustment dial so that the micro-bubbles are below the collection cup cone. Let the pump run for 24 - 72 hours to “break-in” the unit. (5.1) Use fl ow control valve for coarse water level adjustment with Model 65. Use water level adjustment dial for fi ne adjustment.
   NOTE: Initial operation of protein skimmer may produce excess bubbles and waste. Allow collection cup to fi ll-up and discard waste-water until production decreases.

OPERATION

1. Turn water-level adjustment dial to raise water level within the main chamber and cone to desired skimming operation.

DRY SKIMMING OPERATION (5.2)

1. Adjust micro-bubbles to .25" - .75" high inside collection cup cone.

NOTE: Dry skimming will produce a dense foam layer which rises to the top of the cone where it collects until the dry foam overfl ows into the collection cup.
RESULTS:

1. Dry foam (froth)
2. Dark, concentrated waste material (Less Volume)

WET SKIMMING OPERATION (5.3)

1. Adjust micro-bubbles to .75" - 3" high inside collection cup cone.
   NOTE: Wet skimming will produce a thin bubble layer which rises to the collection cup lid where it bursts and slides down the collection cup as wet wastewater.

RESULTS

1. Wet foam
2. Light, diluted waste material (More Volume)

Setup Guide

Setting up the Coralife Super Skimmer is simple and straightforward. Here are the steps:

1. Place the skimmer in the aquarium, ensuring the inlet and outlet hoses are properly positioned.
2. Connect the inlet hose to the pump and outlet hose to the return pump or overflow.
3. Plug in the skimmer and adjust the gate valve to achieve the desired water level and flow rate.
4. Monitor the skimmer's performance and adjust as necessary to achieve optimal skimming.

Maintenance of Coralife Super Skimmer

SAFETY: Always disconnect needle-wheel pump from power supply before removing collection cup or cleaning unit.
WARNING: Only clean with warm fresh water. Do not use any type of chemical cleaning agent to clean the skimmer. These include, but not limited to, soap, detergents, alcohol, glass cleaners, polishers, ammonia, etc.

1. To operate effi ciently, the Super Skimmer must be in use 24 hours a day

DAILY MAINTENANCE

1. Make sure all connections are secure.
2. Observe to see if skimmer is functioning properly and producing waste material.
   NOTE: Skimmer may need to be adjusted accordingly due to variables in water quality and fl uctuations.
3. Check to see if the collection cup is full and empty waste material.
4. Check water outlet vent hole to make sure it is clear of dirt and debris.
5. Check air-inlet silencer and make sure it is clean and free of dirt and debris.

WEEKLY MAINTENANCE

1. Clean the collection cup and neck of organic build up.
2. Clean or replace the sponge and fi lter from the bubble production diffuser.

MONTHLY MAINTENANCE

• Clean water pump.

NOTE: Make sure to follow manufacturer instructions for component’s proper installation, operation and maintenance.

Troubleshooting

NOTE: Variables that affect skimming to produce dry or wet foam are:

1. New Fish or Invertebrates
2. Frequent Feeding
3. Change in Water Chemistry
4. Supplements and Medication
5. Water Quality
6. Water Fluctuations/Evaporation
7. Addition of “Make-up” Water
8. Water Changes
9. Maintenance
10. Inserting hands in the tank

• No microbubbles produced inside the skimmer.
  1. The air-inlet silencer is clogged.
  2. Pump is not plugged in.
• No foam produced inside collection cup
  1. Adjust water level inside the skimmer.
  2. New skimmer may take up to 72 hrs. to adjust properly to aquarium system.
• Water pump is not working.
  1. Check to make sure power is supplied.
     NOTE: Make sure to follow manufacturer instructions for component’s proper installation, operation and maintenance.
• Skimmer water level fl uctuates (pulses).
  1. The output tubing air vent hole is clogged causing the skimmer to create a siphon.
  2. Output tubing is too deep inside of bubble trap. Cut output tubing and allow a 1" space inside the sponge (black).
• Water is rapidly overfl owing into collection cup.
  • Reduce water level in the skimmer. Water level may be too high.
  • Make sure water is fl owing through output tubing. Bubble production diffuser may be clogged, blocking water fl ow.
  • Changes in water chemistry. Readjust water-level adjustment dial to lower water level in skimmer.
  • Output tubing is pushed against white fi lter pad in bubbleproduction diffuser. Allow 1" of space between bottom of output tubing and fi lter pad (white).

Coralife Super Skimmer Warranty

Central Aquatics (Company) warrants this Coralife product (see Exclusions below) to the original purchaser against defective material and workmanship that occurs during normal in-home use for 1year from date of purchase. Company will, at Company’s option, either repair or replace same without charge (but no cash refunds will be made). This warranty is limited to replacement or repair of product only and does not cover loss of aquarium life, personal injury, property loss, or damage arising from the use of the product. You must retain original proof of purchase to validate this warranty.

Pros & Cons

Pros

• Efficient and reliable skimming performance
• Adjustable gate valve for easy fine-tuning
• Unique collection cup design for easy cleaning
• Durable construction for long-lasting use
• Quiet operation for peaceful aquarium environment

Cons

• Higher price point compared to other skimmers
• May require adjustments for optimal performance

Customer Reviews about Coralife Super Skimmer

Customers rave about the Coralife Super Skimmer's effective skimming performance and easy maintenance. The adjustable gate valve is a favorite feature, allowing for fine-tuning of the water level and flow rate. However, some customers note that the skimmer can be a bit noisy at times, especially during start-up.