Introduction

The Little Giant PE-2YSA Parts Washer Pump is a submersible pump designed for use in parts washers with aqueous solutions or UL-listed solvents. Rated for continuous duty, this 1/40 hp pump features a glass-filled polyester housing, nylon volute, and fluoroelastomer shaft seal, making it suitable for industrial, commercial, or residential applications. It delivers 300 gph at a 1' rise and has a maximum shut-off of 12'. The cost of this parts washer pump is typically around $150.00.

NOTE: This pump is intended for use only in parts cleaners listed by Underwriters Laboratories. The combination of the fluid pumped, the pump, and the design of the parts washer will determine if additional safety devices such as low liquid level cut off are required. Refer to parts washer manufactur-er’s instructions to see if this is required.

The PE-1YSA and PE-2YSA are designed for submerged use only. The pump motors are encapsulated in an epoxy resin and are intended to pump the following fluids: Metal parts cleaning solvents - Unheated metal parts cleaning solvents (clas-sified as PJQU as described in the Gas and Oil Equipment Directory). These solvents are refined petroleum distillates, which are free from tendency to heat spontaneously. They have a closed cup flash point not lower than 100°F. The low flash point of these combustible liquids does present a moderate fire hazard. Operating the pump fully submerged offers added protection from fire risk.
Aqueous cleaning solutions 
These are water-based solutions that should not be used in excess of 140°F and a maximum pH of 12. These are typical fluids that are compatible with the pump materials.

WARNING

1. The low flash point of these combustible liquids does present a moderate fire hazard. Operating the pump fully submerged offers added protection from fire risk. For other solvent handling precautions, consult the material safety data sheet (OSHA–20 form, or equivalent) for the solvent used.
2. Use any metal parts cleaning solvents that are UL approved or aqueous cleaning solutions. The use of fluids such as gasoline and lower flash point solvents is dangerous and may cause explosions or fire.

PUMP PERFORMANCE (115V, 60 HZ)

Detailed Specifications

• Models: PE-1YSA & PE-2YSA
• Suction Inlet: 3/4" MNPT
• Discharge Outlet: 1/4"-18 MNPT
• Cord Type: 18/3 (SJTOW-A)
• Pipe Connector Around Cord: 1/2-14 MNPT, Brass
• Pump Housing (Volute): Nylon
• Motor Housing: Polyester
• Impeller: Nylon
• Pump Screen: Polyethylene
• Pump Shaft Seal: Viton®
• Motor Shaft: 440 S.S.
• Volute Screws: 316 S.S.
• Overall Dimensions (PE-1YSA): 4.75 x 2.90 x 5.39 inches
• Overall Dimensions (PE-2YSA): 5.40 x 2.90 x 5.55 inches
• Maximum Fluid Temperature: 140°F (Aqueous) - 100°F (Solvent)
• Maximum pH of Fluid: 12 pH

REPLACEMENT PARTS LIST

Description

The Little Giant Washer Pump PE-2YSA features a robust and corrosion-resistant thermoplastic body, ensuring long-lasting performance in various environments. The pump's motor is designed for efficiency and reliability, making it suitable for continuous operation. Its compact size allows for easy installation in tight spaces, and the silent operation ensures it won't disrupt daily activities. The pump includes a check valve to prevent backflow and comes with a 1-1/2" NPT discharge for easy connection to existing plumbing systems.

Little Giant Washer Pump PE-2YSA Installation

The power cord supplied with this pump should not be in contact with solution. The solution may attack the cord insulation causing cord to become stiff or lowering the insulating properties. The pump is supplied with a three-conductor power cord. The third conductor is to ground the pump to prevent possible electrical shock hazard.

1. Seal the power cord inside of liquid-tight, 1/2" NPT, steel intermediate metal conduit. Use caution to ensure the cord will have no nicks or cuts.
2. Consult the pump nameplate data for proper voltage and frequency. The black (or brown) and white (or blue) wires are live and the green (or green/ yellow) wire is the ground wire.
3. Be sure that the pump is fully submerged in the cleaning solution.
4. Connect the pump power cord to a properly grounded, grounding–type receptacle.
5. The pump must be protected by a GFCI (Ground Fault Circuit Interrupter) when pumping water-based solutions.

Setup Guide

To set up the Little Giant Washer Pump PE-2YSA, follow these steps:

1. Connect the pump to your washing machine's discharge hose.
2. Place the pump in the desired location, ensuring it is submerged in water to prevent overheating.
3. Connect the discharge hose to the 1-1/2" NPT outlet on the pump.
4. Plug in the power cord and test the pump to ensure proper operation.
5. Install the provided check valve to prevent backflow and ensure smooth operation.

MAINTENANCE

DISCONNECT THE PUMP FROM THE POWER SOURCE BEFORE ATTEMPTING TO SERVICE OR REMOVE ANY COMPONENT!

1. This unit is permanently lubricated. Oiling is not required.
2. Periodic cleaning of the pump parts will prolong the LIFE and EFFICIENCY of the pump. Refer to Figure 2 for the assembly and disassembly of the pumping head.
3. Lightly clean any corrosion or debris which may clog the impeller. Use a brush and penetrating oil and lightly scrape. NOTE: Do not allow sediment from parts being washed to build up and restrict the flow of fluid into the pump.
4. Turn the impeller by hand to make sure it is free. If it does not turn or if pump is tripping circuit breaker, or not operating properly after cleaning, return to Little Giant. Do not attempt repairs yourself. If it does turn replace volute and re–install into parts washer.
5. Be certain power cord is protected from solvent and contains no nicks or cuts.

SAFETY INFORMATION

1. Before servicing the pump, see solvent and equipment manufacturer’s instructions for further safety information and possible hazards.
2. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA).
3. This pump must be properly grounded while in use to protect the operator from electrical shock.
4. The pump must be protected by a GFCI (Ground Fault Circuit Interrupter) when pumping water-based solutions.
5. Always disconnect power source before working on the pump. If the power disconnect point is out of sight, lock in the open position and tag to prevent unexpected application of power.
6. Do not attempt to make your own parts cleaners.

TROUBLESHOOTING

1. Should the unit fail to operate, check the following:
   1. Power supply and connections?
   2. Is the pump below liquid level?
   3. Is air trapped in the pump head?
   4. Is there sediment build–up over pump inlet?
2. An air lock or bubble will prevent the unit from pumping. Trapped air can usually be removed by turning the pump off and restarting. Ensure that the discharge line is sloping upward to prevent formation of air pockets.
3. If these operations do not restore the unit to full service, call your dealer or service technician.

Little Giant Washer Pump PE-2YSA Pros & Cons

Pros

• Reliable Performance: Designed for continuous operation with a robust motor.
• Compact Design: Ideal for tight spaces and easy installation.
• Silent Operation: Minimizes noise disturbance.
• Durable Construction: Corrosion-resistant thermoplastic body for long-lasting use.
• Easy Setup: Simple installation process with clear instructions.

Cons

• Limited Flow Rate: May not be suitable for high-volume drainage needs.
• Dependence on Power: Requires a power source, which can be a limitation in areas with frequent power outages.
• Care Required: Regular maintenance is necessary to ensure optimal performance.

Customer Reviews

Customers have generally praised the Little Giant Washer Pump PE-2YSA for its reliability and ease of installation. Many users have noted that the pump operates quietly and efficiently, making it a great choice for residential use. However, some users have mentioned that the flow rate could be higher and that regular maintenance is crucial to extend the pump's lifespan.

Common complaints include issues with the pump's check valve and occasional overheating if not properly submerged in water.