National Comfort Products T-Series Non Condensing Furnace CP8 User Manual

Content

National Comfort Products T-Series Non-Condensing Furnace CP8 Manual

Introduction

The national comfort products T-Series Non Condensing Furnace CP8 is a self-contained, through-the-wall heating and cooling system designed for multifamily residences, apartments, hotels, assisted-living facilities, and other spaces where a compact packaged HVAC solution is required. Unlike a traditional split furnace and air-conditioning system, the Comfort Pack combines gas heating and cooling components in one factory-wired cabinet.

The CP8 uses an approximately 80% AFUE non-condensing gas furnace with a sealed combustion chamber, stainless-steel heat exchanger, diagnostic LEDs, and a sight glass for flame observation. Depending on the selected model, heating output can reach approximately 51,200 BTU/h, while cooling capacities range from compact residential sizes to 2.5 tons. The T-Series design also supports a slide-out cooling chassis, service access, and an adjustable five-speed indoor blower motor.

This unit is best suited to property owners, HVAC contractors, facility managers, and maintenance teams seeking dependable replacement equipment for existing Comfort Pack wall sleeves. It is not a portable appliance or a standard indoor furnace; the cabinet must be installed through an exterior wall by a qualified HVAC professional.

Pricing varies by capacity, cabinet configuration, region, installation labor, and distributor availability. A practical equipment-only estimate is approximately $4,000 to $8,000, while a complete installed replacement may range from $7,000 to $14,000 or more. Confirm current pricing, model availability, and compatibility with an authorized National Comfort Products distributor.

Specifications and Performance

Product family: Comfort Pack T-Series gas heating and cooling system.
Furnace type: Non-condensing gas furnace.
Heating efficiency: Approximately 80% AFUE, with model-specific efficiency commonly listed in the 81.5%–82.5% range.
Heating output: Model-dependent; selected T-Series configurations provide up to approximately 51,000 BTU/h output.
Cooling capacity: Model-dependent, including configurations up to 2.5 tons.
Cooling efficiency: T-Series R-410A configurations are listed at approximately 11.7 SEER2; newer refrigerant configurations may differ.
Heat exchanger: 409 stainless steel.
Blower motor: Adjustable five-speed DC indoor motor.
Electrical supply: Common models use 208/230 V, single-phase, 60 Hz power; verify the unit nameplate before installation.
Gas compatibility: Natural gas or propane with the correct factory or field conversion kit.
Service features: Slide-out furnace and cooling chassis, diagnostic LEDs, sight glass, service ports, prewired connections, and included filter.

Compared with a conventional split system, the CP8 saves indoor mechanical-room space and simplifies replacement in buildings with compatible wall sleeves. Compared with higher-efficiency condensing furnaces, it generally has simpler venting and drainage requirements but lower fuel efficiency.

How to Install and Configure the CP8

Installation must be performed by a licensed HVAC contractor. The CP8 is intended for exterior-wall, through-the-wall installation only and must not be operated as a free-standing indoor furnace.

Confirm the model, heating input, cooling capacity, refrigerant type, gas type, voltage, wall-sleeve dimensions, and required clearances.
Inspect the existing sleeve, exterior grille, wall opening, gas piping, electrical circuit, thermostat wiring, and condensate or drain connections.
Position the cabinet in the approved exterior-wall opening and secure it according to the installation manual.
Connect the gas supply, electrical service, thermostat, blower wiring, drain connections, and approved venting or combustion-air components.
Install the supplied air filter and verify that supply and return openings are unobstructed.
Check gas pressure, electrical polarity, grounding, refrigerant connections, airflow, temperature rise, and combustion performance.
Set the thermostat to heat and cool modes, then test each operating sequence independently.

Never bypass safety switches, operate the furnace with panels removed, or modify venting without written manufacturer instructions. If the unit fails to start, check the disconnect, circuit breaker, thermostat call, filter condition, gas shutoff valve, and diagnostic LED pattern before contacting a technician. Do not attempt gas-valve, burner, ignition, or refrigerant repairs without proper certification.

CP8 Troubleshooting Guide

Furnace Does Not Start

Confirm that the thermostat is calling for heat, the service disconnect is on, the circuit breaker has not tripped, and the gas valve is open. Replace a dead thermostat battery if applicable. If the diagnostic LED indicates ignition failure, flame loss, pressure-switch trouble, or limit operation, record the flash pattern and contact a qualified technician.

Blower Runs but There Is No Heat

Check whether the thermostat fan is set to “On,” inspect the filter, and verify that the gas supply is available. Restricted airflow, an open high-limit switch, failed ignition components, or incorrect gas pressure can prevent heating. Do not repeatedly reset the furnace if ignition fails.

Insufficient Heating

Replace a dirty filter, open closed supply registers, and ensure return-air paths are clear. A technician should measure temperature rise and verify the blower-speed setting, burner operation, heat-exchanger condition, and duct restrictions.

Cooling Problems

Check thermostat mode, indoor airflow, outdoor grille obstruction, and circuit breakers. Poor cooling may result from a dirty coil, incorrect airflow, refrigerant leakage, or a failed capacitor or compressor. Refrigerant service requires certified equipment and trained personnel.

Warranty and Support

Warranty coverage depends on the exact model, registration status, installation, and current manufacturer terms. Keep the model and serial number, installation date, contractor invoice, and service records. For parts, manuals, warranty questions, and authorized service, contact National Comfort Products through its official customer-support or distributor channel rather than using an unverified third-party repair source.

Pros and Cons

Advantages

Space saving: Combines heating and cooling in one through-the-wall appliance.
Replacement convenience: Designed for compatible Comfort Pack wall-sleeve applications.
Service access: Slide-out components and diagnostic LEDs can simplify maintenance.
Durable construction: Stainless-steel heat exchanger and sealed combustion design support long-term use when correctly maintained.
Flexible airflow: Five blower-speed selections help contractors balance comfort and static pressure.
Good retrofit value: It can avoid major ductwork changes in multifamily and hospitality properties.

Limitations

Professional installation: Gas, electrical, venting, and wall-sleeve work are not suitable for do-it-yourself installation.
Lower efficiency: An approximately 80% AFUE furnace uses more fuel than a modern high-efficiency condensing alternative.
Compatibility limits: The T-Series chassis must be matched with the correct cabinet and sleeve.
Noise and access: Through-the-wall equipment may transmit operating sound and requires exterior access for some service tasks.
Value comparison: The CP8 is attractive for direct replacements, while a split heat pump or condensing furnace may offer better operating efficiency where installation conditions permit.

Customer Reviews and Buying Advice

Publicly available product feedback for the exact CP8 model is limited compared with mass-market residential furnaces, so verified review averages and authentic individual testimonials should be checked with the installing distributor. Property managers and contractors commonly value the compact packaged design, compatibility with existing Comfort Pack installations, straightforward service access, and dependable gas-heating performance.

Frequently mentioned concerns for this product category include installation cost, limited availability of model-specific parts, operating noise, and the lower efficiency of an 80% AFUE furnace compared with newer condensing equipment. Performance also depends heavily on correct sizing, wall-sleeve condition, airflow setup, and regular filter replacement.

For buyers searching for the national comfort products T-Series Non Condensing Furnace CP8, the unit is a strong choice when replacing compatible through-the-wall equipment in an apartment, hotel, or multifamily building. Request a written quote that includes the exact model number, heating and cooling capacities, refrigerant type, sleeve modifications, labor, permits, startup testing, warranty registration, and future service availability.

PDF

Faqs

How do I set up the National Comfort Products T-Series Non Condensing Furnace CP8 for the first time?

The National Comfort Products T-Series Non Condensing Furnace CP8 is designed for professional thru-the-wall installation through an outside wall. Before startup, confirm that the cabinet is secure, level, and installed with the required clearances. A qualified technician should connect the gas piping, electrical supply, thermostat, and venting, then check for gas leaks and correct line pressure. Keep the installation manual with the homeowner and do not operate the furnace until every connection has been inspected.

What electrical requirements does the National Comfort Products T-Series Non Condensing Furnace CP8 need?

Verify the exact rating on the unit data plate before connecting power. T-Series CP8 models commonly use a factory-wired 230-volt, single-phase, 60-hertz electrical supply, but wiring must match the specific model. Install a properly sized circuit, service disconnect, grounding conductor, and approved overcurrent protection. Electrical work should be completed by a qualified technician. Never modify factory wiring or bypass safety controls to solve a startup problem.

Can the National Comfort Products T-Series Non Condensing Furnace CP8 run on propane?

The National Comfort Products T-Series Non Condensing Furnace CP8 may be configured for natural gas or propane only when the specific model and conversion instructions allow it. Do not connect a natural-gas furnace to propane without the required factory-approved conversion components, regulator adjustments, and combustion testing. A licensed HVAC professional must verify gas type, inlet pressure, burner operation, and carbon-monoxide safety before use. Check the rating plate and installation manual for your exact CP8 model.

Why is my National Comfort Products T-Series Non Condensing Furnace CP8 not heating?

If the CP8 is not producing heat, first confirm that the thermostat is set to heat and the temperature is above room temperature. Check that the electrical disconnect is on, the circuit breaker has not tripped, and the furnace access panels are fully closed. Make sure the filter is clean and supply or return grilles are not blocked. If the inducer, ignition, or gas burner fails to operate, stop resetting the unit and contact a qualified technician.

What should I do if the National Comfort Products T-Series Non Condensing Furnace CP8 repeatedly shuts off?

Repeated shutdowns can result from restricted airflow, a dirty filter, blocked grilles, improper gas pressure, ignition failure, or an activated limit safety. Replace or clean the filter and verify that vents and returns are open. Do not bypass a limit switch, pressure switch, flame sensor, or other safety device. If the furnace continues cycling or displays a fault indication, turn it off and arrange professional service to test airflow, combustion, venting, and control-board operation.

How can I improve the heating performance of my National Comfort Products T-Series Non Condensing Furnace CP8?

For efficient CP8 operation, use a clean filter of the correct size, keep return-air and supply-air openings unobstructed, and avoid closing many registers. Set the thermostat consistently rather than making frequent large adjustments. The furnace must receive the airflow specified for its heating capacity, and temperature rise should be checked by a technician against the model requirements. Proper gas pressure, sealed duct connections, and clear outdoor venting also help maintain reliable heating performance.

How often should I maintain the National Comfort Products T-Series Non Condensing Furnace CP8?

Inspect the National Comfort Products T-Series Non Condensing Furnace CP8 at least annually, preferably before the heating season. Replace or clean the air filter according to household dust levels and the filter manufacturer’s instructions. A qualified technician should inspect the burner, heat exchanger, ignition system, flame sensor, blower, wiring, gas pressure, vent termination, and safety controls. Keep the outside grille and surrounding area clear. Because this is a gas appliance, arrange immediate service if you smell gas or suspect carbon monoxide.

What installation clearances and placement rules apply to the National Comfort Products T-Series Non Condensing Furnace CP8?

The CP8 is intended for thru-the-wall installation in an outside wall, not as a free-standing indoor furnace. The unit must be mounted securely and level, with clearances from combustible materials and vent openings maintained according to the model-specific manual and local codes. Some configurations require the unit to be positioned at least 8 inches above the finished floor. Confirm wall opening dimensions, vent termination clearances, service access, and drainage requirements before installation.

EasyShare Zoom Camera DX7440 Manual

TSG Series General Purpose Freezers