Introduction of Petsafe Drinkwell 2 Gallon Pet Fountain PWW00 

The Petsafe Drinkwell 2 Gallon Pet Fountain PWW00 is a modern and efficient way to keep your pets hydrated. This Petsafe Drinkwell 2 Gallon Pet Fountain provides a constant flow of fresh, clean water for your pets, encouraging them to drink more and stay healthy. The fountain has an estimated price range of $50 to $70 and was launched in 2020.

Detailed Specifications

The Petsafe Drinkwell 2 Gallon Pet Fountain has the following key features

• 2-gallon water capacity 
• Replaceable carbon filters to remove bad tastes and odors 
• Adjustable flow control 
• Low-voltage 12V system for safe operation
• BPA-free plastic construction 
• Dishwasher safe (excluding pump) 
• Rubber feet to prevent sliding

In the Box

Setup Guide

Here's how to set up the Petsafe Drinkwell 2 Gallon Pet Fountain 

1. Remove the fountain from the box and rinse all parts with water.
2. Insert the carbon filter into the filter housing. 
3. Place the pump in the bottom of the fountain and attach the pump cable to the housing. 
4. Fill the fountain with water. 
5. Plug in the fountain and turn on the switch. 
6. Adjust the flow control to your desired level.

Assemble Pet Fountain 

1. Rinse all fountain components (except for the adaptor) with warm water before use. This will remove any residue from the manufacturing process. Place the foam filter inside the bowl as shown.

2. Place the pump inside the foam filter on the bottom of the bowl. The cord will be closest to the hole on the back of the bowl. Press down on the pump to engage the suction cups.

   

3. Once the pump is securely in place, feed the cord through the hole on the back of the bowl and out the notch on the bottom of the bowl.

4. Remove the extra slack from the cord and push the rubber gasket firmly into the hole.

   

5. Attach the rubber connector to the pump tube if it is not already attached.

6. Open the filter housing by using the tabs to pull it apart.

   

7. Rinse the carbon filter thoroughly under cold water to remove any loose carbon dust. Insert the rounded side of the carbon filter into the rounded side (Side A) of the filter housing.

8. Close the filter housing by aligning the clips from the bottom and pressing down until it snaps shut.

   

9. Insert the filter housing into the pump tube. Attach the bottom of the filter housing to the pump tube.

10. Align the bottom tab of the filter housing with the raised notch. The flat side (Side B) of the filter housing will be facing the front of the bowl.

    

11. Attach the tower by aligning it with the raised notches on the back of the bowl.

12. Insert the flow control knob into the hole on the top of the tower. Turn the knob clockwise to maximize the water stream. Turn the knob counter clockwise to decrease the water stream or shut it off.

    

13. Attach the lid to the tower. Pick up the pet fountain by the bowl and place it in a desired location. Pour water into the bowl, leaving 1/2 inch of space between the water level and the rim of the bowl.
14. Make sure the electrical power cord, the adaptor and your hands are completely dry. Connect the in-line plug and make sure no silver is showing, then plug the adapter into a standard electrical wall outlet.

NOTE: Never let the water level fall below 1 inch from the base of the bowl or your pump might fail.

Pet Fountain Cleaning

NOTE:  Replace the carbon filter every 2-4 weeks and replace the foam filter every 1-2 months.

1. Unplug the fountain, and disconnect the in-line plug.
2. Pick up the pet fountain by the bowl, and take it to the sink.
3. Pour out the water, and then disassemble the pet fountain.
4. Discard the carbon filter and the foam filter. See the instructions on page 10 for cleaning your pump. Use a solution of 80% water and 20% white vinegar to remove hard water buildup.
5. Wash all other parts with warm water and soap, or place in the top rack of the dishwasher.

NOTE: Do not place the adaptor, rubber connector or pump in the dishwasher.

Pump Cleaning

1. Remove the faceplate. You may need to use a fingernail to pry it off.
2. Remove the yellow, teardrop-shaped stator by pulling up on the small tab.
3. Use a fingernail to pull out the impeller, which is held in place magnetically. Clean the pump parts with warm water and soap, then reassemble.

Description

The Drinkwell 2 Gallon Pet Fountain is a great option for pet owners who want to ensure their pets have access to fresh, clean water at all times. The fountain's large 2-gallon capacity means you don't have to refill it as often, and the replaceable carbon filters help remove bad tastes and odors from the water. The adjustable flow control allows you to customize the water flow to your pet's preference, and the low-voltage system is safe for use around pets. The BPA-free plastic construction is durable and easy to clean, and the rubber feet prevent the fountain from sliding across the floor.

Troubleshooting of Petsafe Drinkwell 2 Gallon Pet Fountain 

Here are some common problems and solutions for the Drinkwell 2 Gallon Pet Fountain 

• Problem: The fountain is not pumping water.
  Solution: Check to make sure the pump is properly attached and that the fountain is filled with water. If the problem persists, try cleaning the pump and filter.
• Problem: The water flow is too strong/weak. 
  Solution: Adjust the flow control to your desired level. 
• Problem: The fountain is making strange noises. 
  Solution: Check to make sure all parts are properly assembled and that the fountain is filled with water. If the problem persists, try cleaning the pump and filter.

Pros & Cons of Drinkwell 2 Gallon Pet Fountain PWW00 

Pros

• Large 2-gallon water capacity 
• Replaceable carbon filters 
• Adjustable flow control 
• Safe low-voltage system 
• Durable BPA-free plastic construction 

Cons

• The pump may need to be cleaned frequently 
• Some pets may be intimidated by the moving water