Introduction

The Philips Norelco SensoTouch Shaver 1180X is a cutting-edge electric shaver designed for a smooth and comfortable shaving experience. Featuring the GyroFlex 2D contour-following system, it easily adapts to the curves of your face, minimizing irritation while providing a close shave. Its DualPrecision shaving heads effectively tackle both long hairs and stubble, making it versatile for all grooming needs. Priced at approximately $129.99, this shaver combines advanced technology with user-friendly features for optimal performance.

Specifications 

• Advanced GyroFlex 2D system for flexible head movement
• UltraTrack shaving heads to capture hairs of different lengths
• AquaTec technology for both dry and wet shaving
• LED display showing battery level and travel lock indicator
• Charging stand and travel pouch included
• Li-ion battery providing up to 50 minutes of shaving time
• Quick charge feature for a single shave

Philips Norelco SensoTouch Shaver 1180X  Features

Multi-Level Display

• Remove any sticker or protective foil from the display before using shaver.

• Depending on the shaver model, there are 3 different types of displays:

  

Display for Model, 1180X

The display provides the following information:

Charging Indicator

Model 1180X

• When the shaver is charging, the display goes on and the bottom charging light blinks. As charging continues, more and more lights will blink to indicate what level the battery has been charged.
• Quick charge: When the shaver contains enough energy for one shave, the bottom charging light alternately blinks orange and white.

Full Charge Indicator

Model, 1180X

• When the battery has been fully charged, all charging lights light up continuously. After approximately 30 minutes the display automatically switches off again.

Remaining Battery Capacity

Model, 1180X

• The remaining battery capacity is indicated by the number of charging lights that are on.

Low Battery Indicator

Model, 1180X

• When the battery is almost empty (5 or less shaving minutes left), the bottom charging light blinks orange. When you turn the shaver OFF the bottom charging light continues to blink for a few seconds.

Replacement Shaving Unit Indicator

Every year, depending on your shaving behavior, after turning the shaver OFF, the replacement  shaving unit symbol indicator starts to blink. The replacement reminder is repeated at 9  successive shaves or until you reset the shaver. This reminds you that with new shaving heads you will guarantee yourself optimal shaving performance.

Travel Lock
The shaver is equipped with a travel lock function. You can use the travel lock function when you are going to store the shaver for a longer period or if you are going to take the shaver with you when traveling. See ‘Travel Lock’ section for instructions on how to use this function.

Charge Meter 

(1180X)

• Charge Meter monitors amount of remaining battery power available. Remaining battery capacity is based on the amount of power consumed shaving per minute and is dependent upon your skin and beard type, whether you use pre-shave lotion, and how often the trimmer is used.
• Initially your shaver may need to go through 2 or 3 full charge/recharge cycles before remaining battery capacity indicators begin to display your accurate battery power left.

Before First Use

• Charge the shaver before you start using it (see ‘Charging’). Make sure the shaver is switched off before you start charging it.
• Remove any sticker or protective foil from the Display before using shaver.

Important

• Only use the power cord and charging stand or Jet Clean System (models 1180XCC, 1160XCC) provided to charge the shaver.
• The power plug transforms 100-240V AC to less than 24V DC.

Charging

• Charging, recharging or storing at temperatures below 40°F (4°C) or higher than 95°F (35°C) adversely affects lifetime of batteries.
• Charging or recharging requires one full hour.
• A fully charged shaver has a shaving time of up to 50 minutes (models 1190X, 1180X, 1180XCC, 1160X and 1160XCC) or 40 minutes (model 1150X).
• You may recharge when the bottom charging light blinks orange (models 1190X, 1180X, 1180XCC) or the plug symbol blinks (models 1160X, 1160XCC and 1150X).
• Do not charge shaver in a pouch.

Charging in the Charging Stand

1. Connect the small plug of cord to charging stand.
2. Unfold the charging stand. You will hear a ‘click’.
3. Connect the power plug into any 100V to 240V AC outlet. Use only the power cord provided.
   • An adaptor plug may be necessary for power cord usage in some foreign countries. Use an attachment plug adaptor of the proper configuration for the power outlet.

   • The power cord will automatically convert to work on 100V to 240V AC systems.

     

4. Place shaver in stand in an upright position (1). Press the shaver back into the holder until it locks into place (2).
5. The display on the shaver will indicate shaver is charging.

6. Charging requires one full hour. A fully charged shaver has a cordless shaving time of up to 50 minutes (model, 1180X) or 40 minutes.

   

Recharging

Recharging requires one full hour. Recharge when the bottom charging light blinks orange (models 1190X, 1180X, 1180XCC) or the plug symbol blinks (models 1160X, 1160XCC and 1150X).

Quick Charge

When batteries are totally depleted, recharging the shaver for approximately 3-5 minutes gives enough energy for a 3-minute cordless shave.

Put It To The Test & Shaving Tips

• 21 Day Trial and Conversion Process. It is a fact that your skin and beard need time to adjust to a new shaving system.
• Use your new shaver exclusively for 3 weeks to fully enjoy the closeness of a Philips Norelco shave.
• At first you may not get as close a shave as you expect, or your face may even become slightly irritated. This is normal since your beard and skin will need time to adjust. Invest 3 weeks and you’ll soon experience the full joy of your new shaver.
• Stick with it! If you alternate shaving methods during the adjustment period, it may make it more difficult to adapt to the Philips Norelco shaving system.
• If you are still not convinced after 21 days, Philips Norelco will refund you the full purchase price as long as the request is received within 45 days of purchase.

How To Shave With An Electric Shaver

• This symbol on the shaver indicates that the shaver can be used in the bath or shower.
• Make sure the charging stand/Jet Clean System does not get wet or near water.

• Use this shaver for its intended household use as described in this manual.

  

Shaving

1. Turn shaver ON by pressing the on/off button once. Shave against the direction of beard growth using only circular movements.
   The shaver display will light up briefly.

   

2. Stretch your skin with your free hand so blades can lift and cut whiskers. Gently press shaver to skin so the floating heads can follow the contours of your face. DO NOT press too hard. Too much pressure can pinch the skin into the combs.
3. Turn shaver OFF by pressing the on/off button once.
   The display lights up for a few seconds and then shows the remaining battery capacity (Models 1190X, 1180X. 1180XCC).
4. Clean the shaver after each use (see chapter ‘Cleaning’).

5. Put the Protective Cap on the shaver to protect shaver heads.

   

Wet Shaving

You can also use the shaver on a wet face with shaving foam.

1. Apply some water to your skin.
2. Apply shaving foam to your skin.
3. Rinse the shaving unit under the tap to ensure that the shaving unit glides smoothly over your skin.
4. Press the on/off button once to switch on the shaver.
5. Move the shaving heads in circular movements over your skin.
   NOTE: Rinse the shaver under the tap regularly to ensure that it continues to glide smoothly over your skin.
6. Dry your face and thoroughly clean the shaver after each use (see chapter ‘Cleaning’).
   NOTE: Make sure you rinse all foam off the shaver.

7. Put the Protective Cap on the shaver to protect heads.

   

Trimming

To Groom Sideburns and Moustache:

1. Pull the shaving unit straight off the shaver.
   NOTE: Do not turn the shaving unit while you pull it off the shaver.

2. Insert the raised notch of the trimmer into the slot in the top of the shaver (1). Press the trimmer down to attach it to the shaver (2). You will hear a ‘click’.

   

3. Turn shaver ON.
   The display lights up for a few seconds (Model, 1180X).
4. Hold trimmer to exact hairline desired. Move trimmer downward with gentle pressure.
5. Trim beard, moustache or sideburns using the trimmer.
6. Turn shaver OFF when finished.
   The display lights up for a few seconds and then shows the remaining battery capacity (Model, 1180X).
7. Thoroughly clean the trimmer after using.
8. Pull the trimmer straight off the shaver.
   NOTE: Do not turn the trimming unit while you pull it off the shaver.
9. Insert the raised notch of the shaving unit into the slot in the top of the shaver (1). Press the shaving unit down to attach it to the shaver (2). You will hear a ‘click’.

10. Put the Protective Cap on the shaver.

    

Travel Lock

If you are going to store the shaver for a longer time period or if traveling, it is possible to lock the shaver. The travel lock prevents the shaver from being switched on by accident.

Activating the travel lock

1. Press the on/off button for 3 seconds.
   The lock symbol lights up on the display.
   NOTE: The displays of model 1180X look different, but show the same symbol.

2. The travel lock has now been activated.

   

Description

The Philips Norelco SensoTouch Shaver 1180X boasts an ergonomic design with a contoured grip, making it comfortable to hold and maneuver. The GyroFlex 2D system allows the shaving head to pivot in two directions, ensuring a close shave even on hard-to-reach areas. The UltraTrack shaving heads are designed to capture hairs of different lengths in a single stroke, reducing the need for multiple passes.

The AquaTec technology enables both dry and wet shaving, allowing users to shave with or without shaving cream or gel. The shaver also includes an LED display that shows the battery level and indicates when the travel lock is engaged.

Deactivating the travel lock

1. Press the ON/OFF button for 3 seconds.
2. The lock symbol goes out and the shaver turns ON to indicate that the shaver has been unlocked. The shaver is now ready for use.
   The shaver unlocks automatically when charging in the charging stand or Jet Clean System.

Cleaning

• Always clean your shaver after each use.
• Regular cleaning guarantees better shaving results.
• Never clean, remove or replace shaving unit while motor is on.
• Do not apply pressure to shaving head combs. Do not touch shaver heads with hard objects as this may dent or damage precision-made slotted combs.
• Do not use shaver if shaving head combs are damaged or broken. Facial injury may occur.
• Do not use abrasives, scourers or aggressive liquids such as gasoline or acetone to clean the shaver or Jet Clean System.

Cleaning the Shaving Unit

The shaver heads may be quickly cleaned after each use by rinsing with hot water. Water from the tap should be on a hot setting, BUT BE CAREFUL TO TEST WATER FIRST SO AS NOT TO BURN OR SCALD HANDS.
Regular cleaning guarantees better shaving results. While rinsing shaver heads, water may drip out of the base of shaver. This is a normal occurrence.

1. Always turn shaver OFF, remove from charging stand/Jet Clean System before cleaning.
2. For best results rinse the shaving unit by running under hot water for a few minutes. BE CAREFUL TO TEST WATER FIRST SO AS NOT TO BURN OR SCALD HANDS.
3. Pull the shaving head holder off the bottom part of the shaving unit and rinse under hot water for 30 seconds.

4. Carefully shake off excess water and let the shaving unit air dry.
   NOTE: Do not wipe or dry the shaving unit with a towel or tissue. This could damage the shaving heads.

   

5. Push the shaving head holder back onto the bottom of the shaving unit. You will hear a ‘click’.

6. You may also clean the shaving unit and hair chamber without water by using the supplied brush.

   

Cleaning the Shaving Unit in the Jet

Clean System (1180XCC/1160XCC)
CAUTION: Keep cleaning solution out of reach of children. Do not take internally. Avoid contact with eyes. In case of eye contact, thoroughly flush with cold water. If irritation persists, get medical attention.

Important

• Only use this shaver, charging stand, Jet Clean System and HQ200 cleaning solution provided  to charge or clean shaver.
• Other Philips Norelco shavers DO NOT work with this Jet Clean System.
• Empty the cleaning solution canister and thoroughly rinse the canister clean with warm water every 2 weeks.
• The Jet Clean System thoroughly cleans but does not disinfect your shaver, therefore, do  not share shaver with others.
• The charging plug converts 100-240V AC to less than 24V DC.
• the Jet Clean System on a flat, stable and fluid-resistant surface to avoid any leakage. Be careful not to tip or move the Jet Clean System if it is filled with the cleaning solution.
• To avoid evaporation, do not expose cleaning solution to direct sunlight.
• Remove the protective cap from the shaver before charging or cleaning the shaver in the Jet Clean System.
• Use this appliance for its intended household use as described in this manual.

1. Place the Jet Clean System on a flat, level surface.

2. Simultaneously press the buttons located on both sides of the Jet Clean System   (1) and lift the appliance off the Jet Clean canister (2). Always remove appliance from canister by lifting straight up. Do not tilt Jet Clean System.

   

3. Pour the Jet Clean Solution (Model HQ200) into the canister up to a level between the two lines located inside the canister.

   

   NOTE: ONLY USE PHILIPS NORELCO JET CLEAN SOLUTION (MODEL HQ200) WITH THE JET CLEAN SYSTEM. ANY OTHER SOLUTION MAY CAUSE DAMAGE TO YOUR Shaver.

   • When the cleaning solution level drops below the minimum level, the ‘cleaning chamber empty’ symbol will blink and the shaver holder will move to the starting position.
   • If you clean your shaver every day, you should clean and refill the canister approximately every 15 days.

4. Carefully lower the appliance back onto the Jet Clean canister making sure the release buttons snap back into place.

   

When the canister is filled with cleaning solution, do not move appliance to prevent leakage.

Jet Cleaning the Shaver

• If the shaver does not contain enough power for one (1) shave, the Jet Clean Cleaning System may not work properly. Charge the shaver in the Jet Clean System before using the Jet Clean System to clean your shaver.
• If you use the shaver with shaving foam, quickly rinse under hot water before cleaning in the Jet Clean System.

1. Connect the small plug to the Jet Clean System. Connect the charging plug into   any 100V to 240V AC outlet. Use only the charging plug provided.
2. Place the Jet Clean System on a flat, level surface. Fill the canister with cleaning solution (see ‘Preparing Jet Clean System For Use’).
3. Remove protective cap from shaver.
4. Place the shaver head side down in the shaver holder with the display facing the front of the Jet Clean System.

5. Place the shaver into the holder behind the two clips (1) and press the shaver down to lock into place (2). The display on the shaver will indicate shaver is charging.

   

6. Press the ON/OFF button on the Jet Clean System to start the cleaning cycle. The shaver display stops showing the charging indication.

7. The cleaning light starts to blink and the shaver is automatically lowered into the cleaning solution.
   The shaver stops charging while it is being cleaned.

   

   • During the first phase of the cleaning cycle, the shaver will automatically turn on and off several times while the shaver holder lowers and raises the shaver’s position in the cleaning solution, removing all debris. The cleaning light will blink continuously throughout the cleaning program.
   • During the second phase of the cleaning cycle, the shaver holder moves the shaver to the drying position and the drying light will blink. This phase will take approximately 2 hours. The shaver will stay in one position until the end of the drying program.

   • Do not press the ON/OFF button while the cleaning cycle is running. If this does occur, the cleaning cycle will stop and the shaver holder will automatically move to the starting position. The cleaning cycle can be re-started by pressing the ON/OFF button once.

     

   • If the power plug is disconnected before the cleaning cycle is complete, the shaver holder will remain in its current position. Reconnect the plug into the outlet or Jet Clean System and the shaver holder will automatically move to the highest position. The cleaning cycle can be restarted by pressing the ON/OFF button once.
     NOTE: If the cleaning solution level drops below the minimum level during the cleaning cycle, the ‘cleaning chamber empty’ symbol will blink and shaver holder returns the shaver to the starting position, stopping the cleaning cycle. Unplug Jet Clean System from the outlet, remove shaver  and refill canister (see “Preparing Jet Clean System for Use”).

     

8. When the entire cleaning cycle is complete and the shaver is hygienically clean, the shaver will be raised to the starting position and the display on the shaver will turn on indicating that the shaver is (re)charging.
9. Pull the shaver forward and lift shaver from Jet Clean System.
   • If the shaver needs to be recharged, you can simply leave it in the Jet Clean System after cleaning and the shaver will automatically  recharge. The display on the shaver will indicate the shaver is recharging.
   • You may store your shaver in the Jet Clean System.

Extra-thorough cleaning method

Do not mix up the cutters and combs as the shaving performance may be adversely affected for several weeks before optimal shaving performance is restored.

1. Turn shaver OFF.
2. Pull the shaving head holder off the bottom part of the shaving unit.
3. Slide the green retaining frame in the direction of the arrows indicated on the retaining frame.

4. Lift the retaining frame out of the shaving head holder.

   

5. Remove the cutter from the comb. Do not clean more than one cutter and comb at a time, since they are all matching sets. If you accidentally put a cutter in the wrong comb, it may take several weeks before optimal shaving performance is restored.

6. Clean the cutter with the cleaning brush supplied.

   

7. Clean the inside of the comb.
8. After cleaning, place the cutter back into the comb with the cutter legs pointing downwards.
9. Repeat the process for the other two cutters and combs.

10. Place the retaining frame back onto the shaving head holder.

    

11. Slide the retaining frame back into place (‘click’).

12. Reattach the shaving head holder to the bottom part of the shaving unit.

    

Cleaning the Trimmer

Clean the trimmer after each use.

1. Turn shaver ON with trimmer attached to shaver.
2. Rinse the trimmer under hot water. BUT BE CAREFUL TO TEST WATER FIRST SO AS NOT TO BURN OR SCALD HANDS.

3. Remove trimmer from shaver and allow to air dry.

   

Tip: For optional trimmer performance, lubricate the trimmer teeth with one drop of mineral oil every 6 months.

Replacing the Shaving Unit

Replace the shaving unit once a year for optimal shaving results.

• Replace damaged or worn shaver heads with model RQ11 Philips Norelco shaver heads only.
• The individual shaving heads (cutters and combs) are NOT replaceable.

Only Replacement Shaver Head Assembly Indication

After 12 months of use, the replacement head indicator symbol starts to blink to remind you to check if it’s time to replace your shaving unit to obtain optimal shaving results.

Note: The displays of models 1160X, 1160XCC and 1150X look different, but work the same way.

1. Pull the shaving head holder off the bottom part of the shaving unit.
2. Attach the new shaving head holder to the bottom part of the shaving unit (‘click’).
3. To reset the shaver, press and hold the On/ Off button for approximately 10 seconds.

Note: If you do not reset the shaver at the first replacement reminder, it continues to show the shaving unit symbol at 8 more shaves or until you reset the shaver.

Setup Guide

To operate the Philips Norelco SensoTouch Shaver 1180X, 

• Start by charging the device using the provided charging stand. 
• Once charged, simply turn it on and adjust the shaving head according to your comfort level. 
• For wet shaving, apply your preferred shaving cream or gel before turning on the shaver.
• To assemble the shaver, ensure all parts are securely attached. 
• The shaving heads are easy to replace and can be done by simply snapping off the old head and attaching the new one. 
• There is no need for pairing as this is a standalone device.

Maintenance

• Always remove shaver from the charging stand/Jet Clean System before cleaning appliance.
• The charging stand/Jet Clean System and shaver may be wiped clean using a damp cloth.
• Water from the tap should be on a warm setting to clean any washable parts.

Note: DO NOT place or clean any parts of the charging stand/Jet Clean System in a dishwasher.

Philips Norelco SensoTouch Shaver 1180X Storage

The shaver can be placed in the charging stand/Jet Clean System for safe storage.

• If appliance will not be used for an extended period of time, it is recommended that the cleaning solution in the Jet Clean canister be emptied out before storing.
• Be sure shaver is turned off. Remove cord from outlet and charging stand or Jet Clean System before storing in a safe, dry location where it will not be crushed, banged, or subject to damage.
• Do not wrap power cord around shaver/ charging stand or Jet Clean System when storing.
• Store cord in a safe location where it will not be cut or damaged.
• Do not place or store charging stand/Jet Clean System where it can fall or be pulled into a tub or sink, water or other liquid while plugged in.

• If storing shaver in the charging stand, put the Protective Cap on shaver to protect heads.

  

Troubleshooting

If your shaver is not turning on, 

• Check the battery level and ensure it is properly charged. 
• If the LED display is not showing, it may indicate a low battery or a fault in the charging system.

For issues with the shaving head, 

• Clean it regularly to prevent clogging. 

If the shaver is pulling or tugging on your hair, 

• Adjust the angle of the shaving head or consider using it in combination with shaving cream or gel.

FULL TWO YEAR WARRANTY

Philips Electronics North America Corporation warrants each new Philips Norelco Product 1180X (except cutters and combs) against defects in materials or workmanship for a period of two years from the date of purchase, and agrees to repair or replace any defective product without charge.

Philips Norelco SensoTouch Shaver 1180X Pros & Cons

Pros

• Advanced GyroFlex 2D system for a close shave
• UltraTrack shaving heads capture hairs of different lengths
• AquaTec technology for both dry and wet shaving
• Ergonomic design for comfortable handling
• Long-lasting Li-ion battery with quick charge feature
• LED display for easy monitoring of battery level

Cons

• Higher price point compared to basic models
• Shaving heads may need frequent cleaning to maintain performance
• Slightly bulkier than some other models due to its advanced features
• Battery life could be longer for heavy users

Customer Reviews

Customers have generally praised the Philips Norelco SensoTouch Shaver 1180X for its performance and comfort. Many users appreciate the close shave it provides and the ease of use, especially the ability to shave both dry and wet. However, some users have mentioned that the shaver can be a bit loud and that the shaving heads require regular cleaning to maintain optimal performance.