Installation: Seeley International MagIQtouch Controller Instruction Manual

Content

Overview

The MagIQtouch Controller is a touch-screen wall controller used to manage compatible Seeley International heating and cooling systems. It supports single-device and multi-component installations, guided setup, zoning, and day-to-day control from the room where it is mounted.

It is designed for installers and homeowners who want a central controller with temperature sensing, system status feedback, and access to advanced settings such as scheduling, calibration, and component management.

Specifications

Controller cable type: 26AWG, 7/0.16, 6-core flat cable
Supplied standard cable length: 20 m
Additional cable options: 1.5 m, 3 m, 30 m, and 40 m versions
Maximum cable length to first cooler: 25 m
Maximum cable length for additional coolers with a link module: 40 m
Recommended mounting height: about 1.5 m above the floor
Setup access code for protected menus: 7378
Reset access: rear-mounted reset button

Detailed Description

The MagIQtouch Controller uses a built-in temperature sensor and a guided installation wizard to help configure connected components such as coolers, heaters, and sensors. During setup, the controller scans for devices one type at a time and builds a system configuration that can later be edited through the settings menu.

The wall unit has an interactive display, a right-side button used to wake the screen, and menu tabs for navigating between general settings, equipment-specific menus, and service information. In systems with zoning, one controller acts as the master unit while other controllers function as slave controllers in their zones.

For reliable temperature control, the controller should be placed in the most-used room, away from sunlight, drafts, heat sources, and direct airflow from outlets. Correct placement matters because the controller measures room conditions directly at the wall unit.

Safety

Check for hidden electrical cables, gas pipes, and water pipes before drilling.
Keep controller cables away from regular power cables and high-power equipment.
Route cables at least 300 mm from mains wiring and cross power cables at right angles when needed.
Do not modify supplied cables, and do not use non-approved cable types.
Seal the cable entry hole so wall drafts do not affect temperature sensing.
Avoid mounting the controller where sunlight, heat sources, or strong airflow will interfere with readings.

Setup and Operation

Mounting the controller

Remove the bracket from the rear of the controller, use it as a template, and mark the fixing points and cable entry hole. Drill the cable hole to 16 mm and drill the fixing holes to suit the wall type. Use 5 mm holes for plasterboard or 6 mm holes for brick walls, then fit the wall plugs and screw the bracket into place.

Run the cable through the wall cavity, connect it to the controller, and slide the wall unit onto the bracket until it locks into the keyway slots. If needed, a standard stud mounting bracket for wall plates can be used with plasterboard walls.

Starting the system

After the controller is powered, press the button on the right side of the screen to activate the display. For a new installation, choose the all-new system option and follow the installation wizard. Select the correct system type at the start, such as a single component setup or a multiple-component setup.

Single-component installation

For one heater or one cooler with no zones, power the connected unit first. The controller scans for the device, confirms what it finds, and then moves to the operation screen once the user continues.

Multiple-component installation

For more complex systems, connect and power components one at a time in the order prompted by the controller. This prevents communication problems and helps the installation wizard identify each device correctly. The system is complete only when all required components have been found.

Operation screens

From the main operating screens, the user can turn the system on or off, adjust the target temperature, select the primary operating mode, and open advanced display options. The controller also supports manual mode, program mode, and access to the settings menu.

Settings menu

The settings area includes a general menu, cooler and heater menus when those products are installed, and a service menu for component details and fault data. Only the options relevant to the connected system appear on screen. Some settings are protected by the access code 7378.

General menu options

Time and date
Language
Temperature units in Celsius or Fahrenheit
Child access lock
Standby screen brightness
Zone renaming
Status information display
Temperature sensor selection
Software revision
Simple mode lock
Shutdown timer
Auto re-start
Temperature calibration
Install add-on cooler
System configuration
System reset

Service menu

The service menu is intended for competent service personnel and uses the same access code, 7378. It provides component-specific information such as model and serial numbers, plus a service operating screen for troubleshooting and status changes.

Component management

To add a new component, connect it and power it up. The controller detects it and steps through the setup process. When replacing a faulty part, disconnect the old unit, ignore the warning if appropriate, then connect the new unit and choose replace when prompted.

To remove a component permanently, open system configuration from the general menu, enter the access code, let the controller scan the installation, disconnect the component to be removed, and use the modify option to delete it from memory. If a future replacement is likely, choose ignore instead of deleting it.

Controller reset

The rear reset button can reset the controller alone or the complete system. A full system reset restores factory default addresses for all connected components and requires the installation wizard to be run again from the start.

New controller or pre-used controller

A new controller connected to an existing system must scan the installation before it can operate. Because system configuration is stored in controller memory, the information cannot be transferred between controllers. Any pre-used controller must be reset before being connected to another system.

Fault handling

When a fault occurs, the controller shows a fault screen and lets the user resolve or ignore the issue. A fault icon remains visible on the lower taskbar while any fault is still active, and it can be tapped to review current faults.

Faults are grouped into auto reset faults, running faults, service faults, and service agent faults. Some faults only reduce performance, while others shut a component down until repaired.

Slave controllers and zoning

In multi-controller systems, one master controller governs the system and the others act as slave controllers. If the master is off, no other zone can run. If the master is on, slave controllers can switch their zones on or off. The master also controls the primary mode selection.

For evaporative cooling, zone behavior follows the temperature sensed in the master zone, and set temperature or fan speed changes apply across the whole system. For gas ducted heating and integrated cooling, each zone can use manual or program mode independently, and the zone temperature is set from the controller in that zone.

After a power outage

Following a power loss, the controller prompts for time and date. If auto restart is enabled, the system returns to the previous operating mode before time and date entry is completed.

Troubleshooting

No display: check that the cable is fitted correctly, then refit it or replace it if damaged.
System shows on but the fan does not run: the set temperature may already have been reached, or the program schedule may be set to off for the current time period.
Use the status information display option when more detail is needed during diagnosis.

Pros & Cons

Pros: guided installation wizard, flexible system support, protected service menus, and detailed fault handling.
Pros: supports zoning and controller replacement workflows without rebuilding the whole system from scratch.
Cons: correct installation is important, and component ordering matters during setup.
Cons: some advanced menus are locked behind an access code, which can slow casual adjustments.

PDF

Faqs

How do I mount the MagIQtouch Controller in the right location for accurate temperature control?

Mount the MagIQtouch Controller about 1.5 metres above the floor in the room you use most often, since the built-in thermostat depends on that location for accurate sensing. Avoid direct sunlight, exterior walls, nearby heat sources like TVs or stoves, and places with strong drafts or dead air such as cupboards. Also make sure the wall cavity is sealed around the cable entry so hot or cold air does not distort the reading.

What cable requirements and length limits should I follow when installing the MagIQtouch Controller?

Use the supplied 26AWG, 7/0.16, 6-core flat cable and do not modify it. Keep the controller cable at least 300 mm away from regular power cables and high-power equipment, and cross power cables at right angles if they must intersect. The maximum cable length from the controller to the first cooler is 25 metres, and additional coolers added through a link module can be up to 40 metres away. Non-approved or altered cables can affect operation and may not be covered.

How do I start a new MagIQtouch Controller installation?

For a brand-new setup, power up the heater or cooler first, then select the all-new system option on the controller. The installation wizard will guide you through the process. If you are installing a single component with no zones, choose the default single-component option. For a multi-component system, select the multi-component option so the controller can identify each device in the correct order.

Why does the MagIQtouch Controller need components connected one at a time during setup?

The controller scans one device type at a time, so heaters, coolers, and sensors must be connected and powered up one by one when prompted. If two devices of the same type are connected together during setup, communication can become corrupted and the system may not work properly. Following the installation wizard in order helps the controller assign each component correctly and finish the system scan without errors.

What should I do if the controller cannot find my heater or cooler during the installation scan?

If the scan does not detect a component, first check that the heater or cooler is connected correctly and powered on. Then review the cable connection and try the retry option. The controller is expecting to find only the device type currently being installed, so make sure no extra same-type components are connected too early. Once the device is found, confirm it and continue with the setup screen.

How do I add a new or replacement component to an existing MagIQtouch system?

To add a new component, connect it and power it up, then let the controller detect it and guide you through setup. If you are replacing a faulty part, disconnect the old unit first, then connect the new one. The controller should offer a replace option, which is the correct choice for a swap. When replacing more than one faulty component, connect each new device of the same type one at a time.

How do I reset the MagIQtouch Controller or the whole system?

Use a pin or paperclip to press and hold the reset button on the back of the controller. You can reset just the controller or reset the whole system, depending on what you need. A full system reset returns every connected component to factory default addresses, so you must run the installation wizard again from the beginning. This is also required before using a pre-used controller with another system.

What do the fault icons and service messages on the MagIQtouch Controller mean?

When a fault occurs, the controller shows a fault screen and a small fault icon remains on the lower taskbar until the issue is cleared. Minor auto-reset faults are logged but may not be shown to the user, while running faults allow reduced operation. Service faults shut the component down but may still be fixed by the user, and service agent faults require professional help. The service menu can also show component details and diagnostic screens for troubleshooting.