Startech.com 1U Steel Vertical Wall Mount Rack Bracket RK119WALLV User Manual
Content
StarTech.com 1U Steel Vertical Wall Mount Rack Bracket RK119WALLV Manual
Introduction: Compact 1U Vertical Wall-Mount Rack Storage
The startech.com 1U Steel Vertical Wall Mount Rack Bracket RK119WALLV provides a compact way to install standard 19-inch rack equipment directly against a wall. Its open-frame, L-shaped design supports compatible network, data, and AV equipment while minimizing the space required by a conventional cabinet or floor-standing rack.
This vertical rack mount bracket is suitable for patch panels, power distribution strips, switches, networking accessories, and other 1U equipment that follows the EIA-310 19-inch rack standard. It is especially useful in small offices, wiring closets, retail installations, classrooms, workshops, and home labs where floor space is limited.
The steel construction provides a durable mounting platform, while the 16-inch mounting-hole spacing is designed to align with common wall-stud spacing. The bracket can also be mounted horizontally, such as beneath a desk, when the installation surface and equipment orientation permit. Included cage nuts, rack screws, and wood screws simplify basic installation.
Use the RK119WALLV when a full server cabinet is unnecessary but secure rack mounting is still required. Its flush wall-mounting format keeps equipment organized and accessible while helping reduce cable clutter. Before installation, verify the bracket revision, equipment weight, wall construction, and clearance requirements for the specific application.
Specifications of the RK119WALLV 1U Steel Rack Bracket
- Product type: 1U vertical wall-mount equipment rack bracket
- Rack compatibility: Standard 19-inch rack equipment
- Rack standard: EIA-310 compatible
- Construction: Steel open-frame bracket
- Form factor: L-shaped mounting design
- Mounting orientation: Vertical wall mounting; horizontal mounting may also be used where appropriate
- Wall-mounting pattern: Six mounting holes, including holes spaced approximately 16 inches center to center for common stud layouts
- Equipment mounting: Square M5 cage nuts and M5 rack screws
- Typical applications: Network switches, patch panels, power strips, and other compatible 1U devices
- Maximum load: Up to 130 lb or 59 kg for revision 03 and later; earlier revisions may be limited to approximately 125 lb or 56 kg
- Included hardware: Wall-mounting screws for wood surfaces, cage nuts, rack screws, and installation documentation
Load capacity applies only when the bracket is correctly attached to a suitable structural surface using appropriate fasteners. The wall, anchors, studs, and installed equipment must collectively support the complete operating load.
How to Install the StarTech RK119WALLV Wall Mount Rack Bracket
- Confirm that the intended wall or mounting surface can support the bracket and the fully equipped rack load. Locate suitable studs or use anchors rated for the surface and load.
- Hold the bracket in the desired position and check equipment clearance, cable access, ventilation, and door or walkway clearance.
- Use the six mounting holes as a template. Mark the mounting points, ensuring the bracket is level and the fasteners align with structural support.
- Drill pilot holes when required. Use the supplied self-tapping screws only for suitable wood surfaces. For masonry, metal studs, or drywall, select compatible load-rated hardware.
- Secure the bracket firmly, then check for movement or flex before installing equipment.
- Install the supplied square M5 cage nuts in the rack openings that match the equipment mounting ears.
- Position the 1U device on the rails and tighten the M5 rack screws evenly with a Phillips screwdriver. Do not overtighten.
- Connect network, power, and data cables while maintaining service loops and avoiding sharp bends.
Safety warning: Do not install the bracket on an unsuitable surface or rely on the included wood screws for non-wood construction. Support heavy equipment during installation, keep ventilation openings clear, and verify that the final load remains within the applicable bracket revision limit.
RK119WALLV Troubleshooting and Maintenance
Bracket moves or feels unstable
Remove the equipment and inspect every fastener. Confirm that screws are fully seated and attached to studs or correctly rated anchors. Do not operate the installation until the wall connection is secure.
Rack equipment does not align
Check that the device uses a standard 19-inch, 1U mounting pattern. Reposition the M5 cage nuts to match the equipment ears, and confirm that the bracket is not twisted or mounted out of level.
Cage nuts will not fit
Use square M5 cage nuts in the square mounting holes. Install each nut with a cage-nut tool or carefully engage one edge before pressing the opposite edge into place. Avoid forcing an incorrectly sized nut.
Cables are difficult to connect
Plan cable routing before tightening the equipment. Leave sufficient side and front clearance, use short patch cables where practical, and avoid placing the bracket where connectors press against the wall.
Preventive maintenance
Inspect fasteners periodically, especially after installing or removing equipment. Check for wall movement, corrosion, bent steel, loose cage nuts, and excessive cable strain. Keep the bracket and equipment free of dust that could affect ventilation.
The product documentation should be used for revision-specific load limits and installation details. For warranty or technical assistance, contact StarTech.com support through the support section of the official StarTech.com website and provide the model number, bracket revision, installation surface, and a description of the problem.
Pros and Cons of the StarTech.com 1U Steel Vertical Wall Mount Rack Bracket RK119WALLV
Advantages
- Space efficient: Mounts compatible 1U equipment against a wall instead of occupying floor space like a cabinet or floor rack.
- Broad application range: Works well for patch panels, power strips, network hardware, and compact data installations.
- Standard compatibility: Supports 19-inch EIA-310 rack equipment and uses common M5 cage nuts and screws.
- Stud-friendly design: The approximately 16-inch mounting-hole spacing can simplify alignment with common wall framing.
- Flexible placement: The bracket may be installed vertically or horizontally when the application allows.
- Durable structure: Steel construction is more rigid and durable than many lightweight plastic or thin-duty mounting solutions.
Limitations
- Limited rack capacity: It provides only 1U of rack space and is not a substitute for a multi-device server cabinet.
- Surface-dependent installation: The supplied wood screws are not universal wall hardware; masonry, metal studs, and drywall require suitable fasteners.
- Open-frame exposure: Unlike an enclosed cabinet, the bracket does not provide physical security, dust protection, or cable concealment.
- Clearance planning required: Wall-mounted equipment may be harder to access if connectors or cables face the mounting surface.
- Best suited to compact systems: Users needing extensive cable management, cooling infrastructure, or multiple rack units should choose a larger wall-mount cabinet or rack.
The RK119WALLV is best for installers, IT technicians, small businesses, and home-lab users who need a simple 1U 19-inch vertical rack mount. Choose a different rack solution when enclosed protection, higher equipment density, or advanced cable management is required.
Faqs
How do I install the startech.com 1U Steel Vertical Wall Mount Rack Bracket RK119WALLV for the first time?
What wall surfaces and fasteners are compatible with the startech.com 1U Steel Vertical Wall Mount Rack Bracket RK119WALLV?
Which devices can be mounted in the startech.com 1U Steel Vertical Wall Mount Rack Bracket RK119WALLV?
How do I mount equipment when the cage nuts in the startech.com 1U Steel Vertical Wall Mount Rack Bracket RK119WALLV do not line up?
Can the startech.com 1U Steel Vertical Wall Mount Rack Bracket RK119WALLV be mounted under a desk?
What should I do if the startech.com 1U Steel Vertical Wall Mount Rack Bracket RK119WALLV flexes or pulls away from the wall?
How can I improve cable management and equipment access with the startech.com 1U Steel Vertical Wall Mount Rack Bracket RK119WALLV?
How should I maintain the startech.com 1U Steel Vertical Wall Mount Rack Bracket RK119WALLV?
More startech.com manuals
- Startech.com 1U Horizontal Cable Management Panel CMPNL1UC User Manual
- Startech.com 1U Rack Mount PDU with C13 Outlets PDU08C13H User Manual
- Startech.com 1U Server Adjustable Mounting Rack Rail UNIRAILS1UB User Manual
- Startech.com 1U Rackmount LCD Console With KVM Switch CABCONS1716I User Manual
- Startech.com 1U Rackmount LCD Console With KVM Switch RACKCONS1716 User Manual
- Startech.com 1U Rackmount LCD Cabinet Console 1UCABCONS17 User Manual
Leave a Comment
