Setup: Sunjoe SJSW26M-RM 26-Inch Push Lawn Sweeper Instruction Manual

Content

Overview

The SJSW26M-RM 26-Inch Push Lawn Sweeper is a walk-behind yard-cleanup tool for collecting leaves, grass clippings, twigs, paper, and similar dry lawn debris. Its manually driven brushes rotate as the sweeper moves forward, gather material across a wide path, and direct it into the removable hopper bag.

Designed for residential outdoor maintenance, this push lawn sweeper combines a steel-and-rubber construction with adjustable brush height. It is useful for lawns, patios, sidewalks, and driveways when the surface is suitable for manual sweeping and free of liquids or hazardous materials.

Specifications

Model: SJSW26M-RM
Drive type: Walk-behind push operation
Construction: Steel and rubber
Brush-to-wheel ratio: 4.25:1
Brush diameter: 10 inches (25.4 cm)
Sweeping width: 26 inches (66 cm)
Hopper capacity: 52.3 gallons (198 liters)
Wheel diameter: 9.8 inches (25 cm)
Weight: 34 pounds (15.4 kg)
Brush height: Adjustable
Power source: Manual pushing; no engine, battery, or power cord

Detailed Description

The sweeper assembly contains the rotating brush mechanism, while two wheels provide movement and drive the brushes. The handle frame connects to the supporting legs and gives the operator control while pushing. A one-handed locking adjustment changes the brush position to suit the surface and debris.

The hopper bag is held by a long bag rod at the upper frame and a short bag rod near the sweeper housing. Plastic straps secure the bag flaps to clips on the supporting legs. When full, the bag can be emptied by tipping the sweeper forward or by removing the hopper assembly from the frame.

Named components include the handle frame, long bag rod, hopper bag, supporting legs, wheels, sweeper assembly, brush-height locking knob, height-adjustment tube, short bag rod, bag rod clips, washers, carriage bolts, nylon lock nuts, handle knobs, and wrench.

Safety

Read the operating instructions before assembly or use, and use common sense throughout operation.
Never allow passengers to sit or stand on the sweeper, and do not permit children to operate it.
Keep the sweeper away from fires and excessive heat. The hopper and brushes can burn.
Do not exceed the 52.3-gallon (198-liter) hopper capacity.
Use extra care on rough ground, near ditches, and on hillsides to reduce the risk of tipping.
This equipment is not intended for streets or highways. Watch for traffic when working near a roadway.
Inspect the sweeper after it strikes a foreign object. Repair or replace damaged or worn parts before use.
Never collect toxic, carcinogenic, combustible, or otherwise hazardous substances, including pesticides, asbestos, lead, arsenic, barium, or beryllium.
Do not collect burning cigarettes, ashes, matches, or other hot or smoking materials.
Wear heavy gloves when removing glass, metal, or other sharp objects from the hopper.
Wear safety goggles because sweeping can propel dust or foreign material toward the eyes.
Do not use the sweeper for liquids, expose it to rain, or store it outdoors unprotected.
Remain alert. Do not operate when tired, distracted, or affected by alcohol, drugs, or medication that reduces control.

Setup

Assembly requires a 10 mm wrench. Before starting, lay out all components and hardware and check for damage or missing parts.

Attach each supporting leg to the sweeper assembly with an M6 x 30 carriage bolt and an M6 nylon lock nut. Leave the hardware loose at this stage.
Fit the handle frame over the supporting legs and align the mounting holes.
Join the handle frame and supporting legs using the specified carriage bolts, bag rod clips, flat washers, lock washers, and handle knobs.
Fully tighten the hardware installed during the first step.
Install two bag rod clips on the inside of each supporting leg. Secure each clip with an M6 x 30 carriage bolt, flat washer, lock washer, and handle knob.
Slide the long bag rod through the stitched upper channel of the hopper bag.
Slide the short bag rod through the stitched lower channel.
Place the hopper assembly on the frame by inserting the long rod into the two frame clips and the short rod into the openings on both sides of the sweeper housing.
Hook the plastic bag straps beneath the bag clips on the supporting legs.
Before operation, verify that the bag is correctly mounted and every fastener is tight.

Operation

Adjusting the Brush Height

Turn the brush-height locking knob counterclockwise to release the adjustment.
Hold the handle and raise or lower it to position the brushes for the surface.
If necessary, use your other hand to slide the height-adjustment tube while setting the brush position.
Turn the locking knob clockwise to secure the selected height.

Sweeping Technique

Push the sweeper forward at a normal walking pace. The brush mechanism operates during forward movement and does not sweep when the unit is pulled backward. Mow grass to an even height before sweeping so the brushes can contact the surface consistently.

Use controlled passes rather than forcing the machine through heavy accumulations. If the hopper becomes full, stop and empty it before continuing. Do not use the sweeper to collect wet material, liquids, hot debris, or hazardous substances.

Emptying the Hopper

Stop the sweeper in a safe location away from flames or other heat sources.
Tip the sweeper forward to allow the collected material to fall out.
Alternatively, remove the hopper bag from the frame and empty it separately.
Empty the hopper after every use. Damp grass and wet leaves can damage the bag if left inside during storage.

Cleaning and Maintenance

Empty and clean the hopper after each use.
Rinse the inside and outside of the sweeper after use, then allow it to dry completely.
Periodically inspect all nuts, bolts, and screws and tighten them as needed.
Clean the working components and apply light lubrication once a year.
Apply a glossy enamel spray paint to scratched or worn painted metal areas to help protect the finish.
Never overload the hopper beyond 52.3 gallons (198 liters).

Lubricating the Drive Components

The wheel bearings are factory lubricated, but the brush-shaft bearings should receive a few drops of light oil twice a year. The gear should be cleaned every two years and then coated evenly with light grease.

Use a screwdriver to remove the hub cap.
Remove the circlip and flat washer so the wheel, gear, and shaft are accessible.
Remove the circlip securing the gear, then lift the gear away.
Clean the gear and lubricate the shaft as required.
Reinstall the gear, circlip, wheel, flat washer, and hub cap in reverse order.

Replacing the Brushes

Remove the hopper bag and turn the sweeper over.
Remove the nuts and bolts securing the brush retainers.
Take out the worn brushes along with the long and short retainers.
Place the replacement brushes between the long and short retainers.
Secure the brush components with the M6 nuts and hex bolts.
Fit the brush assembly onto the brush shaft and secure it with the M5 nut and M5 bolt.
Repeat the procedure for the remaining brush assembly.
Check that the two brush sets remain vertical to one another after installation.

Storage

Store the sweeper indoors or in a protected area during severe weather and winter. Remove all material from the hopper before storage, and make sure the machine and bag are clean and dry.

Troubleshooting

Brushes do not collect debris: Confirm that the sweeper is being pushed forward rather than pulled backward, and adjust the brush height so the brushes properly contact the surface.
Uneven sweeping: Mow the lawn to an even height, check the brush-height setting, and verify that the brush assemblies are installed in their correct vertical relationship.
Hopper does not sit correctly: Check that the long rod is seated in the frame clips, the short rod is inserted into the housing openings, and every plastic strap is hooked beneath its supporting-leg clip.
Loose or unstable frame: Stop using the sweeper and inspect all carriage bolts, washers, nuts, clips, and handle knobs. Tighten loose hardware before operating.
Brushes or wheel components need service: Remove the hopper, work with the sweeper turned over when required, and inspect the brush retainers, shaft, gear, circlips, and lubrication points.

Warranty

The refurbished SJSW26M-RM is covered for 90 days against defects in materials or workmanship when used for normal residential purposes. Coverage applies to the original purchaser and depends on proper use and maintenance. Wear parts and damage associated with misuse, improper care, or unauthorized changes are not covered under the stated refurbished-product warranty terms.

Pros & Cons

Pros

Wide 26-inch sweeping path helps reduce the number of passes.
Large 52.3-gallon hopper supports extended cleanup before emptying.
Adjustable brush height accommodates different sweeping surfaces.
Manual operation avoids fuel, batteries, electrical cords, and engine maintenance.
Steel-and-rubber construction is designed for durable, straightforward yard use.

Cons

Forward pushing is required because the brushes do not operate while reversing.
The unit is unsuitable for liquids, wet stored debris, hazardous materials, and hot materials.
Manual assembly, periodic lubrication, and brush replacement require routine maintenance.
Rough terrain, ditches, and hills require slower, more cautious operation.

The SJSW26M-RM 26-Inch Push Lawn Sweeper is best suited to users who want a simple, manually operated way to gather dry lawn debris without using a powered mower attachment or motorized collector.

PDF

Faqs

How do I assemble the SJSW26M-RM 26-Inch Push Lawn Sweeper correctly?

Begin by attaching both supporting legs to the sweeper assembly with the supplied carriage bolts and nylon lock nuts, leaving them loose initially. Fit the handle frame over the legs, then secure the frame and bag rod clips with the washers, lock washers, knobs, and bolts. Tighten the first connections fully afterward. Slide the long and short rods through the hopper bag, install them in their clips and housing openings, and hook the bag straps underneath the supporting-leg clips.

How do I adjust the brush height on the SJSW26M-RM lawn sweeper?

Park the sweeper on a stable surface before adjusting the brush height. Turn the brush-height locking knob counter-clockwise to unlock the adjustment, then hold the handle and lift or lower it until the brush position suits the lawn surface. The height adjustment tube may need to be guided by hand while it slides. Once the setting is correct, turn the knob clockwise until it is secure. Confirm that the adjustment is locked before pushing the sweeper.

Why does the SJSW26M-RM not collect debris when I pull it backward?

The SJSW26M-RM is designed to sweep while moving forward, so pulling it backward will not operate the brushes as intended. Push it at a normal walking speed using steady, straight passes. Mow the grass to an even height before sweeping, and check that the brush setting is appropriate for the surface. If collection remains poor, inspect the brushes, wheels, hopper connections, and hardware for damage, looseness, or blockage before using the sweeper again.

What materials can the SJSW26M-RM 26-Inch Push Lawn Sweeper collect?

This push lawn sweeper is intended for common dry lawn debris such as leaves, twigs, and paper. Do not use it to collect liquids, burning cigarettes, ashes, matches, or other hot material. Avoid toxic, carcinogenic, combustible, or otherwise hazardous substances, including materials that may contain dangerous chemicals or fibers. Wear safety goggles during operation because moving brushes can propel foreign material toward the eyes, and use heavy gloves when handling sharp debris.

How should I empty and clean the SJSW26M-RM hopper bag?

Empty the hopper bag after every use. Tip the sweeper forward so the collected material falls out, or remove the hopper bag and dump it separately. Do not unload it near a fire because the brushes and bag can be damaged by heat or flames. After emptying, rinse and dry the inside and outside of the sweeper. Damp grass and wet leaves should not remain in the hopper because prolonged storage can damage the bag.

What should I check if the lawn sweeper becomes difficult to push?

Stop using the sweeper and inspect it before applying more force. Check whether the hopper is overloaded, the brush height is set too low, or debris is caught around the brushes or wheels. Confirm that all nuts, bolts, and knobs are tight and that the wheels rotate freely. If the sweeper recently struck a foreign object, inspect it for bent, cracked, or worn parts. Repair or replace damaged components before returning the SJSW26M-RM to service.

How do I maintain the brushes and gears on the SJSW26M-RM?

After each use, empty and rinse the sweeper, then allow it to dry. Periodically check the fasteners and inspect the brush assembly for wear or damage. The brush-shaft bearings should receive a few drops of light oil twice a year. Clean the gear every two years and apply an even coat of light grease before reinstalling it. When replacing brushes, remove the hopper, turn the sweeper over, and keep the two brush sets vertical to each other during reassembly.

What safety precautions should I follow when operating the SJSW26M-RM?

Inspect the assembled sweeper and fully tighten its hardware before each use. Never allow children to operate it, carry passengers, or use it on streets or highways. Use extra caution on rough ground, ditches, and hillsides to prevent tipping, and watch for traffic near roads. Do not exceed the 52.3-gallon hopper capacity. Keep the sweeper away from fire, avoid rain exposure, wear safety goggles, and do not operate when tired, distracted, or impaired.