Introduction of Grizzly Heavy Duty Floor Drill Press G7944

We are proud to offer the Grizzly Model G7943/44 12 Speed Heavy-Duty Drill Press. The Model G7943/44 is part of a growing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.

The Model G7943 is a bench version and the G7944 is a floor version. The drill press has a 3⁄4 H.P., 1720 R.P.M. motor capable of producing a 3⁄4" hole in steel. There are 12 spindle speeds ranging from 140 to 3050 R.P.M. A work light, cast iron table, and 14" swing all make this a great drill press for most drilling applications.

Parts List

001	P7943001	BASE
002	PB32M	HEX BOLT M10 X 25
003	P7943003	RACK
003A	P7943003A	LONG RACK
004	P7943004	COLUMN
004A	P7943004A	LONG COLUMN
005	P7943005	TABLE BRACKET
006	P7943006	HANDLE
007	P7943007	SETSCREW M3-1.0X 5
008	P7943008	SHAFT
009	PN01M	PIN M6 X 30
010	PRP08M	NUT M6
011	PW16	WASHER M16
012	P7943012	HEX BOLT M16 X 40
013	P7943013	TABLE BOLT
014	P7943014	TABLE ARM BRACKET
015	P7943015	TABLE
016	P7943016	CLAMP BOLT
017	P7943017	GEAR
018	P7943018	WORM GEAR
019	P7943019	RACK RING
020	P7943020	PIN STOP
021	P7943021	SETSCREW M3-1.0X 10
022	P7943022	FEED SHAFT
023	P7943023	DEPTH RING
024	PRP28M	ROLL PIN 5 X 40
025	P7943025	HANDLE BODY

026	P7943026	HANDLE
027	P7943027	KNOB
028	P7943028	COLUMNSHOULDER SHORT
028A	P7943028A	COLUMNSHOULDER LONG
029	P7943029	SLIDEBAR BOLT
030	P7943030	SETSCREW M5-1.5 X 10
032	P7943032	C-CLIP
033	P7943033	SHIFTER BAR
034	P7943034	SLIDEBAR BOLT
035	PB19M	HEX BOLT M8 X 24
036	PW08	WASHERM8
037	PN03M	NUT M8
038	PN08M	NUT M10
039	P7943039	SCREW SPECIAL SET
040	P7943040	NUT M12 X 1.5
041	P7943041	NUT M12 X 1.5
042	P7943042	SPRING CAP
043	P7943043	TORSION SPRING
044	P7943044	SPRING COVER
045	P7943045	SWITCH BOX
046	PS08M	SCREWM5 X 12
047	P7943047	SCREW ST4.2 X 9
048	PS09M	SCREW M5 X 10
049	P7943049	CLAMP CORD
050	P7943050	BODY
051	PB03M	HEX BOLT M8 X 16
052	P7943052	SHIFTER

053	P7943053	SLIDE BAR
054	P7943054	SLIDE BAR
055	P7943055	MOTOR BASE
056	PW06M	WASHER M12
056A	PLW05M	LOCK WASHERM12
057	PN09M	NUT M12
058	P7943058	MOTOR
059	P7943059	MOTOR PULLEY
060	PK34M	KEY 5 X 20
061	P7943061	SETSCREW M3-1.0X 5
062	P7943062	V-BELT
063	P7943063	CENTER SHAFT
064	P7943064	BALL BEARING P6202
065	P7943065	BALL BEARING P6202
066	P7943066	C-CLIP
067	P7943067	CENTER PULLEY
068	PW16	WASHER M6
068B	PW16	WASHER M6
069	PS24M	SCREW M6 X 10
070	PS08M	SCREW M5 X 12
071	PW16	WASHER M6
072	P7943072	KNOB
073	P7943073	PULLEY COVER
074	P7943074	V-BELT
075	P7943075	PULLEY NUT
076	P7943076	SPINDLE PULLEY
077	P7943077	INSERT PULLEY
078	P7943078	C-CLIP
079	P7943079	BALL BEARING P6205

080	P7943080	SPACER
081	P7943081	BALL BEARING P6205
082	P7943082	C-CLIP
083	P7943083	ROUND NUT M17 X 1
084	P7943084	WASHER
085	P7943085	BALL BEARING P6205
086	P7943086	RUBBER WSHR 62 X 50 X 2
087	P7943087	SPINDLE SLEEVE
088	P7943088	BALL BEARING P6205
089	P7943089	SPINDLE
090	P7943090	ARBOR
091	P7943091	CHUCK
092	P7943092	CHUCK KEY
093	P7943093	LIGHT BODY
094	P7943094	LIGHT BASE
094A	P7943094A	SCREW
095	P7943095	LIGHT SCREW
096	P7943096	SWITCH BASE
097	P7943097	SWITCH (LIGHT)
098	P7943098	SWITCH MOTOR
098B	P7943098B	SWITCH KEY
099	P7943099	C-CLIP
100	P7943100	PIN 18 AWG/3 METERS
100B	P7943100B	WIRE GASKET
100C	P7946100C	MOTOR CORD
101	PAW05M	ALLEN®WRENCH 5MM
102	PAWO3M	ALLEN®WRENCH 3MM
103	P7943103	WEDGE
104	P7943104	WARNING LABEL
105	P7946105	WARNING/ID LABEL
106	P7943106	SPEED CHARTLABEL
107	P7943107	GRIZZLY BLACK/AL LABEL

GRIZZLY MODEL G7943 12 SPEED DRILL PRESS

Category	Feature	Specification
Design Type	Bench Model	-
Overall Dimensions	Table	11-3/8" x 11-3/8"
	Overall Height	38"
	Overall Width	14"
	Overall Depth	24"
	Column Diameter	3.150"
	Quill Diameter	2.040"
	Shipping Weight	160 lbs.
	Box Size	32" L x 20-1/2" W x 11-1/2" H
	Footprint	18" x 11"
Construction	Table	Precision Ground Cast Iron
	Column	Cylindrical Ground Steel
	Base & Head	Cast Iron
Capacities	Spindle Travel	3-1/4"
	Max. Distance, Spindle to Base	23"
	Max. Distance, Spindle to Table	16"
	Spindle Taper	MT #2
	Swing	14"
	Chuck Size	5/8" (16mm), keyed
	Number of Speeds	12, Belt Controlled
	Speeds	140, 260, 320, 380, 480, 540, 980, 1160, 1510, 1650, 2180, 3050 R.P.M.
	Drilling Capacity	3/4" Diameter in Steel
Motor	Type	TEFC Capacitor Start Induction
	Horsepower	3/4 H.P.
	Phase/Cycle	Single Phase / 60 Hz
	Voltage	110V
	Amps	9
	R.P.M.	1720
	Power Transfer	V-Belt Drive
	Bearings	Shielded & Lubricated Ball Bearings
	Switch	Toggle ON/OFF Switch, w/ Safety Lock Tab
Features	Table	360° Swivel Around Table Center, 360° Swivel Around Support Column, Tilt -90° to + 90°, Lock Levers, Coolant Trough
	Vertical Table Movement	Crank Handle Operated Rack and Pinion
	Illumination	110 Volt Socket, Separately Switched
	T-Slot	4 - 5/8" x 3-7/8", Accommodates 1/2" Clamping Kit
	Depth Gauge	On Feed Handle Hub, Inch Increments

GRIZZLY MODEL G7944 12 SPEED DRILL PRESS

Category	Feature	Specification
Design Type	Floor Model	-
Overall Dimensions	Table	11-3/8" x 11-3/8"
	Overall Height	64"
	Overall Width	14"
	Overall Depth	24"
	Column Diameter	3.150"
	Quill Diameter	2.040"
	Shipping Weight	172 lbs.
	Footprint	18" x 11"
Construction	Table	Precision Ground Cast Iron
	Column	Cylindrical Ground Steel
	Base & Head	Cast Iron
Capacities	Spindle Travel	3-1/4"
	Max. Distance, Spindle to Base	49"
	Max. Distance, Spindle to Table	31-1/2"
	Spindle Taper	MT #2
	Swing	14"
	Chuck Size	5/8" (16mm), keyed
	Number of Speeds	12, Belt Controlled
	Speeds	140, 260, 320, 380, 480, 540, 980, 1160, 1510, 1650, 2180, 3050 R.P.M.
	Drilling Capacity	3/4" Diameter in Steel
Motor	Type	TEFC Capacitor Start Induction
	Horsepower	3/4 H.P.
	Phase/Cycle	Single Phase / 60 Hz
	Voltage	110V
	Amps	9
	R.P.M.	1720
	Power Transfer	V-Belt Drive
	Bearings	Shielded & Lubricated Ball Bearings
	Switch	Toggle ON/OFF Switch, with Safety Lock Tab
Features	Table	360° Swivel Around Table Center, 360° Swivel Around Support Column, Tilt -90° to + 90°, Lock Levers, Coolant Trough
	Vertical Table Movement	Crank Handle Operated Rack and Pinion
	Illumination	110 Volt Socket, Separately Switched
	T-Slot	4 - 5/8" x 3-7/8", Accommodates 1/2" Clamping Kit
	Depth Gauge	On Feed Handle Hub, Inch Increments

Detailed Specifications

The Grizzly Heavy Duty Floor Drill Press G7944 is a powerful and accurate drilling machine, designed for heavy-duty applications. Here are its key features and specifications:

20-inch swing and 14-speed drilling capacity (170-3070 RPM)
3/4 HP, 110V, 1 phase motor for powerful performance
Cast iron worktable (14-inch x 14-inch) with T-slots and locking handle for precision and stability
Spindle travel of 4 inches with depth stop for accurate drilling
Adjustable quill for easy tool changes and maintenance
Built-in work light and convenient on/off switch for user comfort
Sturdy and stable base with leveling feet for stability and versatility
Weight: 217 lbs for durability and reliability

Unpacking

The Model G7943/44 is shipped from the manu-facturer in a carefully packed carton. If you dis-cover the machine is damaged after you’ve signed for delivery, immediately call Customer Service for advice. When you are completely satisfied with the condition of your shipment, you should inventory its parts.

WARNING: If moving this machine up or down stairs, the machine must be dis-mantled and moved in smaller pieces. Make sure floor and stair structures are capable of supporting the combined weight of the machine parts and the people moving them.

CAUTION: The G7943/7944 represents a heavy load at 160/172 pounds. Seek assistance before beginning assembly.

Piece Inventory

After all the parts have been removed from the carton, you should have

Headstock
Table Assembly
Base
Column Assembly
Drill Chuck and Key
Drift Key
Allen Wrenches (2)
Hex Bolts, M10 x 25 or 40 (4)

In the event that any nonproprietary parts are missing (e.g. a nut or a washer), we would be glad to replace them, or, for the sake of expediency, replacements can be obtained at your local hard-ware store.

Clean Up

The unpainted surfaces are coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. Avoid chlorine-based solvents as they may damage painted surfaces should they come in contact. Always follow the usage instructions on the product you choose for clean up.

WARNING: Do not use gasoline or other petroleum-based solvents. They have low flash points which make them extremely flamma-ble. A risk of explosion and burning exists if these products are used. Serious personal injury may occur if this warning is ignored.

CAUTION: Many of the solvents commonly used to clean machinery can be toxic when inhaled or ingest-ed. Always work in well-ventilated areas far from potential ignition sources when dealing with sol-vents. Use care when dis-posing of waste rags and towels to be sure they do not create fire or environ-mental hazards.

WARNING: Do not smoke while using solvents. A risk of explo-sion or fire exists and may result in serious personal injury.

Site Considerations

FLOOR LOAD
Your Model G7943/7944 represents a moderate weight load in a small footprint. Most commercial or home shop floors should be sufficient to carry the weight of the Model G7943/7944. If you ques-tion the strength of your floor, you can opt to rein-force it. Ensure that the stand or bench you use with the Model G7943 is capable of supporting the machine.
WORKING CLEARANCES
Working clearances can be thought of as the dis-tances between machines and obstacles that allow safe operation of every machine without lim-itation. Consider existing and anticipated machine needs, size of material to be processed through each machine, and space for auxiliary stands and/or work tables. Also consider the relative position of each machine to one another for effi-cient material handling. Be sure to allow yourself sufficient room to safely run your machines in any foreseeable operation.
LIGHTING AND OUTLETS
Lighting should be bright enough to eliminate shadow and prevent eye strain. Electrical circuits should be dedicated or large enough to handle combined motor amp loads. Outlets should be located near each machine so power or extension cords are not obstructing high-traffic areas. Be sure to observe local electrical codes for proper installation of new lighting, outlets, or circuits.

CAUTION: Make your shop “child safe.” Ensure that your workplace is inaccessible to youngsters by closing and locking all entrances when you are away. Never allow visitors in your shop when assembling, adjust-ing or operating equip-ment.

Assembly

Beginning Assembly

WARNING: Disconnect power to the machine when perform-ing any maintenance, assembly or adjust-ments. Failure to do this may result in serious personal injury.
WARNING: Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back.
WARNING: Wear safety glasses dur-ing the entire assembly process. Failure to com-ply may result in serious personal injury.

Most of your G7943/44 Drill Press has been assembled at the factory, but some parts must be assembled or installed after delivery. We have organized the assembly process into steps. Please follow along in the order presented here.
TOOLS REQUIRED: 11⁄16" open end wrench, rub-ber or wooden mallet and (2) Allen wrenches (supplied).

Column/Base

The G7944 is a floor model and must be secured to the floor using anchor bolts, or the base should be secured to a piece of plywood. The G7943 must be secured to a bench.

WARNING: Do not use a mobile base. Drill presses are extremely top heavy. A stable base is required to prevent serious bodily injury.

Unplug machine before assembly.
G7944: Secure the base to the floor using the appro-priate anchor bolts. or Secure base to a piece of 4' x 4' x 3⁄4" plywood. Using the holes in the base as a guide, drill and bolt the base to the back center of the plywood using carriage bolts.
G7943: Secure base to a bench top capable of holding approximately 160 lbs plus the weight of the workpiece. Using the holes in the base as a guide, drill and bolt the base to the bench top using carriage bolts.
Place the column on the base and line up the mounting holes. Insert and tighten the M10-1.5 hex head bolts with a wrench.

Table Support

Thread the 12mm table lock handle 3 turns into the table support bracket as shown in Figure 4.
Insert the pinion gear into the hole on the side of the table support bracket from the inside, starting with the pinion shaft as shown in Figure 4. Align setscrew in crank handle with flat on pinion gear shaft and secure using the 3mm Allen® wrench provided as shown in Figure 5.
Examine the rack and note that the gear teeth extend farther on one end than the other. The end of the rack where the gear teeth are closest to the end should be posi-tioned down. Insert the rack into the table support bracket and align it with the pocket as shown in Figure 5. The gear teeth on the rack must also face out.
Slide the table support bracket onto the col-umn while holding the rack in place. Allow the bracket to go down until the bottom of the rack contacts the shoulder on the column support as shown in Figure 5. Secure the table support bracket with the lock handle.
Slide the column ring onto the column with the inside bevel in the down position as shown in Figure 6. Adjust the ring until the tip of the rack fits inside the bevel. Tighten the setscrew on the ring.

NOTICE: Use caution when tightening setscrew. Over tightening will split the column ring.

Headstock

CAUTION: The headstock repre-sents a heavy load. Seek assistance before begin-ning this step.

There is a pocket in the bottom of the head-stock for the column to be placed. Seek assistance to help position the headstock over the column. Allow the headstock to slide down until it stops (approximately 4").
Position the headstock directly over the base by using a plumb bob. Use a measuring tape or ruler across the drill press base to find its center. Suspend the plumb line from the cen-ter of the headstock label and lower the bob until it is near the tape/ruler as shown in Figure 7. Adjust headstock from side to side until the tip is equidistant from both the left and right sides.
Tighten the two setscrews shown in Figure 8

Handles: Three handles are supplied with the drill press. Thread them into the handle hub.

Installing Light Bulb

The Model G7943/44 has a light socket that uti-lizes standard sized 40 watt bulbs. Before installing a light bulb, unplug the drill press. Secure bulb in opening behind the spindle.

WARNING: Use only bulbs that are “safety coated” and shatter resistant. The bulb will be exposed at the bottom of the head casting which helps with illumination. Impacts with a bulb not “safety coated” may shatter, exposing the electrical filaments and creating an electrical shock hazard.

Drill Chuck and Arbor

heavy_duty_floor_drill_chuck_and_arbor_drill_press_g7944.png

The drill chuck attaches to the drill spindle by means of a drill chuck arbor. Matched tapers on the arbor and back of the chuck create an almost permanent assembly when properly joined. To assemble the drill chuck and mount it to the spin-dle, carefully follow the instructions below:

The drill chuck, arbor and spindle socket must be thoroughly cleaned and dried before assembly. It is recommended that mineral spirits be used for this task. Refer to the safe-ty warnings on the container of the mineral spirits. Failure to clean the mating sur-faces may result in separation and an unsafe condition. Separation is usually caused by oil or grease on the taper.
Use the provided chuck key to adjust the jaws of the chuck until they are well inside the drill chuck body.
Place the drill chuck on a workbench face down. The arbor has a short taper and a long taper. Place the short taper into the socket in the back of the drill chuck and tap with a rub-ber or wooden mallet as shown in Figure 10. If the chuck fails to remain secure on the arbor, repeat step 1 and 2.
Slide the arbor into the spindle socket while slowly rotating drill chuck. The socket has a rectangular pocket in which the tang (or flat portion of the arbor) fits into. Once the tang is oriented correctly the drill chuck will not rotate without turning the spindle.
Tap the end of the drill chuck with a rubber or wooden mallet to seat it as shown in Figure 11.

CAUTION: DO NOT use a steel hammer on the drill chuck to seat it onto the spindle. Damage will occur to the chuck and/or spindle which may make them unusable or unsafe.

Arbor Removal

A drift key is included to aid in the drill chuck arbor removal.

Rotate the spindle handles until the slot is exposed in the side of the quill.
Rotate the spindle until the inner slot is aligned with the outer as shown in Figure 12. You will see through the spindle when the slot is properly aligned.
Insert the drift key into the slot and allow the quill to rise, trapping the drift key. Hold the drill chuck with one hand and tap on the drift key with a hammer as shown in Figure 13.

Description

The Grizzly Heavy Duty Floor Drill Press G7944 is a versatile and reliable drilling machine, suitable for a wide range of applications, from woodworking and metalworking to construction and maintenance. Its powerful motor and robust construction ensure consistent and accurate performance, while its user-friendly design and features make it easy to operate and maintain. Whether you're drilling holes in wood, metal, or plastic, the Grizzly Heavy Duty Floor Drill Press G7944 is a reliable and efficient tool that will help you get the job done right.

Adjustments of Floor Drill Press G7944

Speed Changes

Unplug the drill press before changing speeds. The drill press has 12 speeds ranging from 140 to 3050 R.P.M. There is a speed chart located under the belt guard. Refer to the chart while reading these instructions.

Loosen the belt tension lock knobs on both sides of the headstock by turning counter-clockwise as shown in Figure 14.
The motor should be free to move. Rotate the belt tension lever counterclockwise to take tension off the V-belts as shown in Figure 15.
Locate the desired speed on the chart and move the V-belts to the desired V-grooves on the motor, idler and spindle pulleys.
Rotate the belt tension lever until the belts are tight. Tighten both lock knobs.
Close the cover.

Depth Stop

Your drill press comes with a depth stop adjust-ment for use when drilling.

Loosen the depth collar lock knob as shown in Figure 16.
Secure the wood stock you will be drilling onto the drill press table.
With the desired bit installed, lower the spin-dle until the tip of the bit just touches the wood stock you will be drilling. Hold the spin-dle in this position.
Turn the depth collar to the desired depth indicated by the scale on the collar. Secure the collar by tightening the lock knob.
Remove the wood stock and test the depth stop by measuring how far the spindle travels when the handles are rotated as shown in Figure 17.

You can also lock the spindle in the down posi-tion for operations such as spindle sanding.

Loosen the depth collar lock knob as shown in Figure 16.
Rotate the spindle to the desired depth and hold it steady.
Rotate the the collar clockwise until it stops, and tighten the lock knob.
Slowly release the drill press handle. The spindle should not move.

Table Adjustment

The table can be adjusted for height, rotation and angle.

Loosen the support bracket lock knob. Turn the table hand crank to lift or lower the table as shown in Figure 18.
Always lock the support bracket in place before operating the machine.

Adjust rotation

Loosen the lock handle located under the table as shown in Figure 19. Rotate the table the desired amount.
Always lock the table rotation in place before operating the machine.

Adjust angle

Turn the nut indicated by the arrow in Figure 18, in a clockwise direction. This will draw the location pin out of the casting. Once loose, pull the pin and nut out, and set it in a safe place until needed.
Loosen the large bolt in the center of the sup-port bracket.
Rotate the bracket to the desired angle. Use the scale on the side of the bracket or a pro-tractor to set the angle. Lock in place by tightening the bolt.

When repositioning the table to 0˚ position, loosen the large bolt in the center of the support casting. Rotate the support casting until the degree scale reads 0˚. Carefully tap the location pin back into the hole from which it came until it stops. Unscrew the nut on the location pin until it is flush with the end of the threads. This will pro-tect the threads when you tap it into place with a hammer. Turn the nut clockwise until it is snug against the casting and then tighten the large bolt in the center. The table is now set to the factory pre-set angle.

Operations

Test Run

Once assembly is complete and adjustments are done to your satisfaction, you are ready to test run the machine.
Turn on the power supply at the main panel. Flip the START button. Make sure that your finger is poised on the paddle switch, just in case there is a problem. The drill press should run smoothly, with little or no vibration or rubbing noises. Strange or unnatural noises should be investigat-ed and corrected before operating the machine further.
If you cannot easily locate the source of an unusual noise or vibration, contact our service department for help.

Drill Bit Changes

Make sure to secure the bit firmly in place. When changing bits, proceed as follows:

Disconnect the machine from power source.
Open the chuck wide enough to accept a new bit.
Install the bit so the chuck jaws will grab as much of the bit shank as it can. Do not allow the chuck to grab the fluted body of the drill bit. Make sure small drill bits do not get trapped between the edges of two jaws.
Tighten the chuck with the chuck key using any of the three key end locations.
Remove the chuck key and reconnect power source.
Reverse steps to remove drill bit.

Grizzly Heavy Duty Maintenance

General

Regular periodic maintenance on your Model G7943/44 will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. Check for the following conditions and repair or replace when necessary:

Loose mounting bolts.
Worn switch.
Worn or damaged cords and plugs.
Damaged V-belt.
Any other condition that could hamper the safe operation of this machine.

Tables

The nonpainted surfaces on the Model G7943/44 should be protected against rust and pitting. Wiping the machine clean after every use ensures that wood dust will not trap moisture against bare metal surfaces.
Some woodworkers recommend using automo-tive paste wax on exposed steel and cast iron sur-faces. The wax provides a layer of protection, as well as reducing friction between lumber and the table, making cuts faster and smoother. Avoid waxes that contain silicone or other synthetic ingredients. These materials can find their way into lumber that is being worked, and can make staining and finishing difficult. If you use paste wax, make sure that it is 100% Carnauba wax.

Lubrication

Since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. Do not lubricate them.

V-Belt

Inspect regularly for tension and wear. Check pul-leys to ensure that they are properly aligned. See pulley/V-belt sections for proper tension and pul-ley alignment procedures.

Grizzly Closure

The following pages contain general machine data, parts diagrams/lists, troubleshooting guide and Warranty/Return information for your Model G7943/44.

If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Our trained service technicians will be glad to help you
If you have comments dealing specifically with this manual, please write to our Bellingham, Washington location using the address in Section 3 Introduction.

We have included some important safety mea-sures that are essential to this machine’s opera-tion. While most safety measures are generally universal, Grizzly reminds you that each work-shop is different and safety rules should be con-sidered as they apply to your specific situation. We recommend you keep a copy of our current catalog for complete information regarding Grizzly's warranty and return policy. If you need additional technical information relating to this machine, or if you need general assistance or replacement parts, please contact the Service Department listed in Section 3: General Information.

WARNING: Operating this equipment has the potential for flying debris to cause eye injury. Always wear safety glasses or goggles when oper-ating equipment. Everyday glasses or read-ing glasses only have impact resistant lens-es, they are not safety glasses. Be certain the safety glasses you wear meet the appro-priate standards of the American National Standards Institute (ANSI).

WARNING: The Model G7943/44 was specifically designed for drilling operations. DO NOT MODIFY AND/OR USE THIS MACHINE FOR ANY OTHER PURPOSE. Modifications or improper use of this tool will void the war-ranty. If you are confused about any aspect of this machine, DO NOT use it until you have answered all your questions or seri-ous personal injury may occur.

WARNING: Like all power tools, there is danger asso-ciated with the Model G7943/44. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this tool with respect and caution to lessen the pos-sibility of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.

Drill Press G7944 Troubleshooting

Here are some common problems and solutions for the Grizzly Heavy Duty Floor Drill Press G7944:

Problem: The drill press is not starting.
Solution: Check the power cord and outlet for any issues. Make sure the power switch is in the "on" position. If the problem persists, contact a professional technician.
Problem: The drill press is vibrating excessively.
Solution: Check the leveling feet and make sure they are securely tightened. If the problem persists, check the belts and pulleys for any signs of wear or damage. Contact a professional technician if necessary.
Problem: The drill press is making unusual noises.
Solution: Check the belts and pulleys for any signs of wear or damage. Check the spindle and bearings for any signs of wear or damage. If the problem persists, contact a professional technician.

Warranty

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

Pros & Cons

Pros

Powerful and accurate drilling performance
Robust and durable construction
User-friendly design and features
Versatile and suitable for a wide range of applications
Affordable price compared to similar models

Cons

Heavy and difficult to move around
May require professional assembly and maintenance
May produce noise and vibration during operation

Customer Reviews about Grizzly Heavy Duty Floor Drill Press G7944

The Grizzly Heavy Duty Floor Drill Press G7944 has received positive reviews from many satisfied customers, who praised its performance, durability, and value for money. However, some customers reported issues with assembly, noise, and vibration, and recommended professional installation and maintenance. Some customers also suggested improvements in the instructions and manual.

Search Manuals in: floor-drill

Read More