Introduction

The ITECH Programmable AC Power Supply IT7321 series is a versatile solution designed for various applications in electronics and electrical testing. It offers programmable output with voltage capabilities up to 300 V, current up to 24 A, and power ratings reaching 3000 VA, making it suitable for simulating real-world operating conditions. The cost of the IT7300 series starts at approximately $1,200. Key features include adjustable frequency from 45 Hz to 500 Hz and built-in measurement capabilities, enhancing efficiency in testing environments.

Guarantee

The materials contained in this document are provided “as is”, and is subject to change, without prior notice, in future editions. Further, to the maximum extent permitted by applicable laws, ITECH disclaims all warrants, either express or implied, with regard to this manual and any information contained herein, including but not limited to the implied warranties of merchantability and fitness for a particular purpose.

ITECH shall not be held liable for errors or for incidental or indirect damages in connection with the furnishing, use or application of this document or of any information contained herein. Should ITECH and the user enter into a separate written agreement with warranty terms covering the materials in this document that conflict with these terms, the warranty terms in the separate agreement shall prevail.

Safety Statement

CAUTION

“Caution” signs indicate danger. It is required to pay attention to the contents of these signs during implementation of operations.

The damage to the product or loss of important data may be caused in case of improper operation steps or failure to follow operation steps. Do not continue to implement any improper operation indicated in “Caution” signs when the specified conditions are not fully understood or these conditions are not satisfied.

WARNING

“Warning” indicates danger. It is required to pay attention to the contents of these signs during implementation of operation steps. Personal casualties may be caused in case of improper operation steps or failure to follow these operation steps. Do not continue to implement any improper operation indicated in “Warning” signs when the specified conditions are not fully understood or these conditions are not satisfied.

The power supply is a high-level safety equipment, there is a protected ground terminal. Before Installation or operation, please read the safety signs and instructions in this manual.

Confirm Package Contents

Open the package and check the articles within package box before operation. In case of any non-conformity, missing or appearance wearing, please contact ITECH immediately.

The package box should comprise:

Device name	Quantity	Model	Remarks
Programmable AC Power Supply	x1	IT7300 series	IT7300 series include: IT7321/IT7322/IT7322H/IT7324/ IT7324H/IT7326/IT7326H/IT7322T/ IT7322HT/IT7324T/IT7324HT/IT73 26T/IT7326HT
Power Cord	x1	-	Different types of instruments are equipped with different power cables.For detailed specifications, refer to 1.3 Installation of power cord.
USB cable	x1	-	-
CD	x1	-	Comprising user manual and documents related to programming and grammatical guidelines.
Factory alignment report	x1	-	Test reportbefore delivery

NOTE
After confirming that package contents are consistent and correct, please appropriately keep package box and related contents. The package requirements should be met when the instrument is returned to factory for repair.

Specification

Model		IT7321
INPUT
Phase		1
Voltage		220Vac±10% or 110Vac±10%
Frequency		47-63Hz
Max.Current		6.3A(220Vac) or 10A(110Vac)
Power Factor		0.5(typical)
AC OUTPUT
Max.Power		300VA
Max Current(rms)	0-150V	3A
	0-300V	1.5A
Max Current(peak)	0-150V	9A
	0-300V	4.5A
Phase		1Φ/2W
Total HarmonicDistortion(T.H.D)		≤0.5% at 45-500Hz (Resistive Load)
Crest Factor		3
Line Regulation		0.1% max for a ±10%line change
Load Regulation		≤0.5%FS(Resistive Load)
Response Time		<100uS
SETTING
Voltage	Range	0-300V High, 150/300V Auto
	Resolution	0.1V
	Accuracy	±(0.2%+0.6V)
	Temp. coefficient	±(0.04% per degreefrom 25℃)
Frequency	Range	45-500Hz
	Resolution	0.1Hz at 45-99.9Hz 1Hz at 100-500Hz
	Accuracy	0.1Hz
Phase Angle	Range	0-360°
	Resolution	0.1°
	Accuracy	±1°(45-65Hz)
MEASUREMENT
Voltage(rms)	Range	0-300V

	Resolution	0.1V
	Accuracy	±(0.2%+0.6V)
	Temp. coefficient	±(0.04% per degree from 25℃)
Current(rms)	Range	L:120.0mA *
		M:1.200A *
		H:3.00A*
	Resolution	L:0.1mA
		M:1mA
		H:10mA
	Accuracy	L:±(0.2%+0.6mA)
		M:±(0.2%+6mA)
		H:±(0.2%+40mA)
	Temp. coefficient	±(0.04% per degree from 25℃)
Current(peak)	Range	0-12A
	Resolution	0.01A
	Accuracy	±(1%+0.36A)
	Temp. coefficient	±(0.05% per degree from 25℃)
Power	Resolution	L:0.01W
		M:0.1W
		H:1W
	Accuracy	L:±(0.2%+0.2W) (47HZ-65HZ)
		M:±(0.2%+2W) (47HZ-65HZ)
		H:±(0.2%+4W) (47HZ-65HZ)
	Temp. coefficient	±(0.05% per degree from 25℃)
GENERAL
Memory		10 memories
Sync Output Signal		Output Signal5V,BNC type
Interface(Option)		LAN,USB,RS232
Operation Environment		0-40℃/20-80%RH
Dimension		1/2 19" 2U
Weight		10Kg

Description

The itechate Programmable AC Power Supply IT7321 is engineered to provide high-quality, reliable power for a wide range of applications. Its advanced digital control system ensures precise control over output parameters, allowing users to easily configure and monitor the power supply through an intuitive front panel or remote interfaces.

The device features a compact and rugged design, making it suitable for both benchtop and rack-mount installations. The IT7300 also supports various communication protocols, enabling seamless integration into automated test systems.

Installation Position

The instrument should be installed at well-ventilated and rational-sized space. Please select appropriate space for installation based on the power supply size

Model IT7321

oveview_itechate_programmable_ac_power_supply_it7300.png

Detailed dimensional drawings

Installation of Power Cord

Connect power cord of standard accessories and ensure that the power supply is under normal power supply.

AC power input level

Working voltage for IT7300 series power supply is shown as follows. So please pay attention to the working input voltage.

The AC line switch of IT7321 is located at the bottom of the unit.
The AC line switches of IT7322, IT7322H, IT7324, and IT7324H are located at the rear of the unit. Please pay attention to the AC level setup before provide AC power.
AC power input level:
- Option 01: 220VAC ± 10%, 47 to 63 Hz
- Option 02: 110VAC ± 10%, 47 to 63 Hz
  - IT7326 and IT7326H models support 220V AC input.
  - IT7322T, IT7322HT, IT7324T, IT7324HT, IT7326T and IT7326HT models support 380V AC input.

Connecting AC Input

WARNING: The power cords supplied with this product is certified for safety. In case the supplied lines assembly needs to be replaced, or an extension lines must be added, be sure that it can meet the required power ratings of this product. Any misuse voids the warranty of this product.

Before connecting power cords, turn off the power.

IT7321: Connect standard power cord to the power supply input terminal.

connecting_ac_input_itechate_programmable_ac_power_supply_it7300.png

In the above illustration, one end of the AC power cord is connected to the AC input terminal in the rear panel of the power supply.
Connect the wire, zero line and ground to the corresponding terminal of the device. Before inserting, please loose the screw, lock the screw when it is inserted.
Connect the three terminals brown to line (L), blue to neutral (N), and yellow-green to ground (GND) on the other end of the power cord to your AC distribution panel.

IT7321 AC input connections are the same, and the end of the AC power cord connected to the AC input terminal on the rear panel of the power supply is connected. The user only needs to connect the other end of the AC power cord to the AC distribution panel, the brown terminal is connected to L1, the gray terminal is connected to L2, the black terminal is connected to L3, the blue terminal is connected to N, and the yellow terminal is connected to the GND.
The connection diagram is as follows:

connecting_ac_input_of_the_itechate_programmable_ac_power_supply_it7300.png

Connecting Test Cables (Optional)

Test cables are not standard accessories of the instrument. Please select optional red and black test cables for individual sales based on the maximum current value. For specifications of test cables and maximum current values, refer to “Specifications of Red and Black Test Lines” in “Appendix”.

WARNING

Before connecting test cables, be sure to switch off the instrument. Power switch is in Off position. Otherwise, contact with output terminals in rear panel may cause electrical shock.
To avoid electrical shock, before testing, please make sure the rating values of the testing cables, and do not measure the current that higher than the rating value. All test cables shall be capable of withstanding the maximum short circuit output current of the power supply without causing overheat.
If several loads are provided, each pair of load wires shall safely withstand the rated short circuit output current of the power supply under full load.
Always use test cables provided by ITECH to connect the equipment. If test cables from other factories are used, please check that the test cable can withstand maximum current.

The front panel of IT7300 series power supply is equipped with the front panel output terminal and rear panel output terminal (see 2.2 Introduction of front panel and 2.5 Introduction of rear panel).

Before using the output terminal of the rear panel to connect the device under test (DUT), remove the protective cover or panel covering the output terminal on the rear panel firstly, then connect the test cables, and take the other end of the test cables out of the hole in the protective cover or panel, and then put the protective cover or panel back in place. To avoid the risk of electric shock if the output terminal is accidentally touched during the test operation.

Connection of the front panel output terminal

The models that support the front panel output are IT7321.

The connection method of the front panel output is as follows: directly insert the plug at one end of the cable into the output interface of the front panel, and connect the other end to the DUT.
The maximum output current of the front panel output terminal is 10A. In order to facilitate operation, the user can directly connect the front panel output terminal if the output current is less than 10A.
If the output current of the output terminal of the power supply exceeds 10A, the user must connect the rear panel output terminal. If you want to obtain the specifications of the equipment, please refer to 4.1 Specification.

Connection of the rear panel output terminal

The user can connect the rear panel output terminal according to the power output specifications. Specific connection of IT7321 (after removing the protective cover) is shown in the figure below.

Make sure the power switch of the instrument is off.
Remove the protective cover or panel that covers the rear panel output terminals.
Unscrew the screws of the output terminals and connect the red and black test cables to the output terminals. Re-tighten the screws.
- When maximum current that one test cable can withstand fails to meet the current rated current, use several pieces of red and black test cables. For example, the maximum current is 1,200A, then 4 pieces of 360A red and black cables are required.
Take the other end of the test cables out of the hole in the protective cover or panel and install the cover or panel back.
Connect the other end of the red and black cables to the DUT terminal.

Setup Guide

To operate the itechate Programmable AC Power Supply IT7321,

Start by connecting the device to a suitable power source and ensuring all safety precautions are in place.
Use the front panel controls to set the desired voltage and current levels.
For remote operation, connect the device via USB, LAN, or GPIB and use the provided software to configure and control the power supply.
Assemble the unit according to the provided mounting instructions if you plan to use it in a rack-mount configuration.

Remote Control

IT7300 series AC source (except IT7321) has four standard communication interfaces: LAN RS232, USB, and GPIB. IT7321 has a standard communication interface: LAN/USB/RS232. You can choose any one of them to communicate with PC.

RS232 Interface

There is a DB9 connector at the rear of the power supply, when connect to computer, you need to select a cable with COM port on both side; To active you need to press a button to enable the settings in menu to be the same with the PC communication configuration. You could do the secondary development with all SCPI commands.

Note

The RS232 settings must match the settings in front panel system information.
If any change, please press key to modify the menu: SYST SET\COMM.

RS232 data format

RS232 data is a 10-bit word with one start bit and one stop bit. The number of start bit is not programmable. Stop bit is selectable between 1&2.Besides, you can set the parity bit in the menu using the front panel key. Parity options are stored in a non-volatile memory.

Baudrate
The front panel button allows the user to set baud rate which is stored in the non-volatile memory: 4800,9600,19200 38400, 57600,115200

RS-232 connection
Adopt the RS232 cable with DB-9 interface because the serial port of RS232 can be connected with that of the controller (e.g. PC). The modulating cable of the air-conditioner is not recommended. The pins of plug are shown as the following table. If your computer is provided with a RS232 interface with DB-25 plug, a cable and an adapter with DB-25 plug (one end) and DB-9 plug (the other end) are required (not the modulating cable of the air-conditioner)

Pin Number	Description
1	No connection
2	TXD, transfer data
3	RXD, receive data
4	No connection
5	GND, ground
6	No connection
7	CTS, clear transfer
8	RTS, ready to transfer
9	No connection

RS-232 Troubleshooting

In case of connection failure of RS232, perform following check:

Check if the computer and power supply are provided with same Baud rate, parity check bit, data bit and flow control. The power supply shall be configured with one start bit (fixed) and one or two stop bits.
Just as described in the RS232 connector, appropriate interface cable or adapter shall be adopted. Notes: even if the cable is equipped with right plug, internal wiring may be incorrect.
The interface cable must be connected to the right serial port (COM1 and COM2) of the computer.

Communication Setup

Please ensure the PC and power supply has the same configuration in the following items.

Baudrate: 9600(4800, 9600, 19200, 38400, 57600, 115200). You could enter the system menu to set the baudrate.
Data bit: 8
Stop bit: 1
Parity bit: (none, even, odd)
- EVEN 8 data bits have even parity
- ODD 8 data bits have odd parity
- NONE 8 data bits have no parity
Native machine address: (0 ~31, factory default is 0)
- Start Bit
- 8 Data Bits
- Parity=None
- Stop Bit

USB Interface

Use a cable with two USB ports to connect power supply and PC. You can program through USB interface to achieve all functions of power supply.

The functions of USB488 interface are as follows:

Interface is 488.2 USB488 interface
Receive the following request: REN_CONTROL, GO_TO_LOCAL, and LOCAL_LOCKOUT
When the interface receives MsgID = TRIGGER USBTMC command, it will transmit the TRIGGER command to the function layer

The functions of power supply’s USB488 are as follows:

receive all SCPI commands
device is SR1 enabled
device is RL1 enabled
device is DT1 enabled

LAN Interface

Press the front panel together to access the menu. Select LAN in the Communication from System and then configure Gateway, IP, Mask and SocketPort in the LAN option. Connect the LAN interface of power supply to the computer with a reticle (crossed).

GPIB Interface

Use a IEEE488 bus to connect GPIB interfaces of power supply and PC. Please ensure that the screws have been screwed down in order to have a full connection. Then press SHIFT + SELECT MENU (Menu) to enter the system menu, and then select the Communication to set the GPIB address. The address range of power supply is 0 to 30. After you set the address, please press ENTER button to confirm, GPIB address is saved in nonvolatile memory.

Specifications of Red and Black Test Lines
ITECH provides you with optional red and black test lines, the user can choose the company's test line for testing. For specifications of ITECH test lines and maximum current values, refer to the table below.

For maximum current of AWG copper wire, refer to table blow.

Note: AWG ( American Wire Gage) it means X wire ( marked on the wire). The table above lists current capacity of single wire at working temperature of 30°C. For reference only.

Troubleshooting

If the device does not turn on,

Check the power cord and ensure it is properly connected to both the device and the power source.

For output issues,

Verify that the settings are correctly configured and that there are no short circuits or overloads.

Common problems include incorrect settings,

Overloaded output, or communication interface issues.
Always follow safety instructions to avoid electrical shock or damage to the device.

Pros & Cons

Pros:

High precision and stability in output voltage and current
Programmable via multiple interfaces for flexible control
Robust design with multiple protection features
Compact and versatile for various applications
User-friendly interface for easy setup and operation

Cons:

Potentially high cost compared to non-programmable alternatives
Complex setup may require technical expertise for full utilization

Customer Reviews

Early adopters of the itechate Programmable AC Power Supply IT7321 have praised its reliability and precision. Many users have noted the ease of use and the comprehensive set of features that make it an essential tool in their workflows.

Some common complaints include the high initial cost and the need for technical knowledge to fully leverage its capabilities. However, overall feedback has been positive, highlighting the device's performance and value in professional settings.

Search Manuals in: programmable-ac

Read More