Introduction of Perlesmith TV Wall Mount PSLF6

The TV Wall Mount is a versatile and robust mounting solution designed to accommodate TVs ranging from 37 to 70 inches. With a load capacity of up to 132 lbs, this mount is suitable for a wide range of TV models and brands. The estimated price of the Perlesmith TV Wall Mount PSLF6 is around $40 to $50, making it an affordable option for those looking for a high-quality TV mount. The product was launched in 2020 and has since gained popularity among consumers for its durability and ease of installation.

Detailed Specifications

Compatible with TVs from 37 to 70 inches
Load capacity of up to 132 lbs
VESA compatible (100x100, 200x100, 200x200, 300x200, 300x300, 400x200, 400x300, 400x400, 600x400, 600x600)
Full-motion articulating arm with a 15-inch horizontal extension
Tilt range of -5 to 15 degrees
Swivel range of +/- 45 degrees
Bubble level for easy installation
Magnetic stud finder included
Cable management system for a clean and organized look
Constructed with heavy-duty steel for durability

Tools Needed (Not included)

Description

The Perlesmith TV Wall Mount PSLF6 is a full-motion articulating mount that provides maximum flexibility for TV placement. The mount can be extended up to 15 inches from the wall, tilted up to 15 degrees, and swiveled up to 45 degrees in both directions. This allows for optimal viewing angles and reduces glare on the screen. The mount is VESA compatible, meaning it can accommodate TVs with a variety of mounting patterns. The heavy-duty steel construction ensures that the mount is sturdy and can support the weight of larger TVs. The included bubble level and magnetic stud finder make installation easy, and the cable management system ensures that cords are organized and out of sight.
Weight Restrictions
If your TV weighs more, this mount is NOT compatible.
WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended for use only within the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage and or injury.
Check the VESA Pattern of Your TV before the Installation

perlesmith_tv_wall_mount_pslf6-check_the_vesa_pattern.png

If your TV VESA is greater than 600x400 mm/24x16 in. or less than VESA 200x100mm/8x4in., this mount is NOT compatible.

Setup Guide

Determine the location on the wall where you want to mount the TV.
Use the magnetic stud finder to locate the studs in the wall.
Mark the center of the studs with a pencil.
Attach the mounting plate to the wall using the included hardware and level to ensure it is straight.
Mount the TV to the articulating arm using the VESA pattern on the back of the TV.
Attach the articulating arm to the mounting plate on the wall.
Connect the cables and use the cable management system to organize them.
Adjust the tilt and swivel as needed for optimal viewing.

Verify Your Wall Construction

CAUTION

DO NOT install into drywall alone

perlesmith_tv_wall_mount_pslf6-verify_your_wall_construction.png

Supplied Parts and Hardware

Warning: This product contains small items that could be a choking hazard if swallowed.

perlesmith_supplied_parts_and_hardware_tv_wall_mount_pslf6.png

perlesmith_tv_wall_mount_pslf6-supplied_parts_and_hardware_for_step_2.png

perlesmith_tv_wall_mount_pslf6-supplied_parts_and_hardware_for_step_3.png

Secure the TV Brackets to TV

Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns.

Too short will not hold the TV.
Too long will damage the TV.

CAUTION: Ensure the TV brackets [03] are EQUALLY CENTERED on your TV AND securely fastened in place.

perlesmith_tv_wall_mount_pslf6-ensure_the_tv_brackets.png

(For Flat Back TV)

(For Round Back TV)

(For TV with A “Bump”)
Spacers may be necessary for 2 holes ONLY.

perlesmith_tv_wall_mount_pslf6-(for_tv_with_a_âbumpâ).png

For cable interference or inset holes, use spacers [06] to create extra space between the TV and TV brackets

perlesmith_tv_wall_mount_pslf6-for_cable_interference.png

Attach the Wall Plate [01] to Wall

For wood stud installation
For concrete installation

Wood Stud Option

WARNING

Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled ﬁrmly against the wall plate.
DON'T USE ANCHOR [A3] FOR THIS STEP!
Ensure the wall plate [01] is securely fastened to the wall before continuing to the next step.
Any material covering the wall must not exceed 5/8 in. (16 mm)
Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x 3½ in. (38 x 89 mm)
Stud center must be veriﬁed

Use a stud ﬁnder(not included) to locate wood studs or use an awl (not included) to verify the edges. Mark the edge and center locations.

perlesmith_tv_wall_mount_pslf6-position_the_wall_plate.png

Position the wall plate template [04] at your desired height and line up the holes with your stud center line. Level the wall plate template [04] and mark the holes.

Drill 4 pilot holes using a 7/32 in.(5.5 mm) diameter drill bit. Make sure the depth is not less than 2 9/16 in.(65mm).

perlesmith_position_the_wall_plate_tv_wall_mount_pslf6.png

Install the wall plate using lag screws [A1] and washer [A2]. Tighten the lag screws [A1] only until the washers [A2] are pulled ﬁrmly against the wall plate.

perlesmith_tv_wall_mount_pslf6-install_the_wall_plate.png

Solid Concrete or Concrete Block Option

WARNING

Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled ﬁrmly against the wall plate.
Ensure the wall plate [01] is securely fastened to the wall before continuing to the next step.
Any material covering the wall must not exceed 5/8 in. (16 mm)
Mount the wall plate directly onto the concrete surface
Minimum solid concrete thickness: 203 mm (8 in.)
Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
Never drill into the mortar between blocks

Position the wall plate template [04] at your desired height, level the wall plate template and mark the pilot hole locations.

perlesmith_tv_wall_mount_pslf6-position_the_wall_plate_template.png

Drill 6 pilot holes using a 3/8 in.(10mm)diameter drill bit. Make sure the depth is not less than 2 ¾ in.(70mm). Never drill into the mortar between blocks.

Use the hammer to knock anchors [A3] into the wall. Be sure the anchors [A3] are seated ﬂush with the concrete surface.

Install wall plate using lag screws [A1], washers [A2] and anchors [A3]. Tighten the lag screws [A1] only until the washers [A2] are pulled ﬁrmly against the wall plate. DO NOT over-tighten the lag screws [A1].

Secure the Arm Assembly [02] to Wall Plate [01

Hang the arm assembly [02] to wall plate [01].
Shift the arm assembly [02] along the wall plate [01] to your desired position.
Secure the arm assembly [02] to wall plate [01] using bolts [F1].

perlesmith_tv_wall_mount_pslf6-secure_the_arm_assembly.png

Secure Front Support to Arm Assembly

Make sure the big button in Front Support [08] hangs on the hook of the arm assembly.
Secure the front support [08] to arm assembly [02] using bolts [F2].

Hang the TV onto the Front Support

Adjustments

Loosen the preassembled knob [T].
Adjust TV to your desired tilt angle.
Tighten the preassembled knob [T] to secure the TV in place.

CAUTION
DO NOT over-loosen these four nuts when adjusting the level angle to prevent the TV from falling oﬀ.

Loosen the bolt [F2] .
Level your TV.
Tighten the bolt [F2] to secure the TV in place.

Note: Please take oﬀ the TV before shifting the arm assembly along the wall plate

To better position your mount and TV on your wall, the mount can be horizontally shifted left to right by following these steps.

Loosen the bolts [F1].
Shift the arm assembly [02] to your desired position.
Tighten the bolts [F1] hard.
Repeat the procedures in Step 5 to rehang and secure the TV onto the front support[08].

perlesmith_tv_wall_mount_pslf6-better_position_your_mount.png

Troubleshooting

If the mount is not level, use a level to adjust the mounting plate on the wall before attaching the articulating arm.
If the TV is not sitting flush against the wall, check the VESA pattern on the back of the TV to ensure it is compatible with the mount.
If the articulating arm is not moving smoothly, check for any obstructions or debris in the joints and lubricate as needed.
If the TV is not staying in place, make sure the mounting hardware is tightened properly and the TV is securely attached to the articulating arm.

Pros & Cons

Pros

Full-motion articulating arm for maximum flexibility
Heavy-duty steel construction for durability
Easy installation with included hardware and instructions
Cable management system for organized cords
Affordable price point

Cons

May not be compatible with some older TV models
Some users may find the installation process time-consuming

Customer Reviews

Customers have praised the TV Wall Mount PSLF6 for its sturdy construction and easy installation. Many have noted that the mount is able to support their large and heavy TVs without issue. Some have commented that the cable management system is a great feature that helps keep their home theater area organized. However, some users have reported that the mount is not compatible with their older TV models. Overall, the Perlesmith TV Wall Mount PSLF6 has received positive reviews from consumers and is a great option for those looking for a high-quality and affordable TV mount.

Search Manuals in: pslf6

Read More