Jbl Speaker S36II, S36-AWII

Introduction

The JBL Speaker S36II and S36-AWII are high-quality speakers designed to deliver exceptional audio performance. Whether you want to enhance your home theater experience or enjoy music with crystal-clear sound, these speakers are a perfect choice.

SPECIFICATIONS

Amplifier Power: 150W
Nominal Impedance: 8 Ohms
Sensitivity (2.83V/1m): 90dB
Frequency Response (–3dB): 60Hz – 20kHz
Crossover Frequencies: 650Hz, 3000Hz
High-Frequency Transducer: 1" Pure-titanium dome, with rubber surround, shielded; Elliptical Oblate Spheroidal™ (EOS) waveguide
Midrange Transducer: S36II – 4" PolyPlas™ (polymer-coated cellulose fiber) cone, rubber surround, shielded; Linear Field Proximity™ (LFP) bezel (model S36AWII uses a shielded WeatherPlas™ midrange)
Low-Frequency Transducer: S36II – 6" PolyPlas™ (polymer-coated cellulose fiber) cone, rubber surround, SFG™, magnetic shorting rings, high-temp oversized Kapton® voice coil, HeatScape™ motor structure, cast-aluminum baskets, shielded (model S36AWII uses a shielded WeatherPlas™ woofer)
Baffles: Low diffraction, IsoPower™
Enclosure: Sealed
Network: Straight-Line Signal Path™ (SSP)
Terminals: All-metal, gold-plated, 5-way binding posts
Dimensions (H x W x D): 10-1/4" x 14-5/8" x 5" 260mm x 371mm x 127mm
Weight: 11 lb/5kg

SPEAKER PLACEMENT

Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible. These recommendations are for the optimal placement of the loudspeakers. Use these placement recommendations as a guide. Slight variations will not diminish your listening pleasure. The Studio Series S36II and S36AWII loudspeakers are video-shielded and can safely be placed near a television. The S36AWII loudspeakers are weather-resistant and are specifically designed for outdoor use, such as in a patio area. As noted below, we recommend mounting the speakers under an overhang, such as roof eaves, for added protection. The S36AWII speakers, because they are resistant to moisture, are also appropriate for mounting in a bathroom, although not inside a bathtub or shower stall. Although these loudspeakers are designed as a mirrored pair, the decision as to which one is left or right will depend on the amount of space left between them. A wider stereo image is presented with the tweeter/midrange array outboard, and a tighter image is presented with the array inboard.

For stereo-only applications:

jbl_speaker_s36ii,_s36-awii_stereo-only.png

For home theater applications:

jbl_speaker_s36ii,_s36-awii_home_theater.png

This placement provides a wide spread in sound, supplemented by the center channel speaker.

WALL-MOUNTING

Do not attempt to mount these speakers on a ceiling, on the underside of roof eaves,, or in a shower stall. The S36II and S36AWII loudspeakers may be positioned on the wall either horizontally or vertically. The grille logo on each speaker may be rotated depending on how the speaker is positioned. Gently pull the logo away from the grille slightly, rotate it to the desired position, and let go. The logo will snap back into place. When mounted vertically, the tweeter array may be positioned either up or down, depending on the height of the placement. If the speakers will be above ear level, the tweeter array should be positioned down, preferably no more than two feet above ear level. If the speakers will be mounted very low, it may be best to position the tweeter array upward so that it will be no more than two feet below ear level. The S36II and S36AWII enclosures are specially designed to angle the speakers toward the listener when mounted flush against the wall. When mounting the S36AWII speakers outdoors, we recommend that you place them under an overhang, such as roof eaves, for added protection, and that you use two of the supplied special angle-mount screws per speaker, which angle the speakers downward at a greater-than-usual angle, facilitating water drainage.

NOTE: When using the enclosed angle-mount screws, always use the top two screw locations appropriate for the specific mounting orientation of your S36AWII. Referring to the enclosed installation template, screw locations (1) and (2) are to be used when mounting the S36AWII horizontally so that these locations are on top. To mount the loudspeakers vertically, use locations (2) and (4) or locations (1) and (3), depending on the mounting orientation. Do not mount the S36AWII upside down (with screw locations (3) and (4) on top) because it won’t be able to lock onto the screw heads. Remember that the JBL logo on the tweeter/mid faceplate can be rotated with the choice of speaker position (vertical or horizontal). At least one screw per speaker should be installed in a wooden wall stud. Select an appropriate wall anchor for the other screw. If the special angle-mount screws are not being used, size 10 screws of at least 1-1/2" in length are recommended. If the screws are used in drywall or other surfaces incapable of holding the screw by itself, the selection of proper anchors is essential. The customer is solely responsible for the proper selection and installation of screws, anchors, and other installation hardware. Further installation details are included on the installation template.

Installation of Self-Adhesive

Rubber Pads
If the speaker is to be placed on a surface (such as a table top or shelf) rather than wall-mounted, the enclosed self-adhesive rubber pads are to be attached to the bottom of the speaker cabinet in their designated recessed locations. If the speaker is to be wall-mounted, then the four self-adhesive rubber pads should be attached to the back of the speaker, as shown in the bottom right diagram. When angle-mounting the pads are required, and they need to be installed on the back of the loudspeaker, near the lower edge, so that they are located between the S36AWII back and the mounting surface. Please see the enclosed installation template for more details.
NOTE: The threaded inserts on the bottom of the speakers are to be used only with JBL accessories that have been developed specifically for the S36 and that may become available at a future date. Do not attempt to install bolts or any non-JBL brackets or accessories to these threads, as this might damage the speaker and dislodge the insert.

jbl_speaker_s36ii,_s36-awii_self-adhesive.png

SPEAKER CONNECTIONS

CONNECTION TIPS
Speakers and electronics terminals have corresponding (+) and (–) terminals. It is important to connect both speakers identically: (+) on the speaker to (+) on the amplifier and (–) on the speaker to (–) on the amplifier. Wiring “out of phase” results in thin sound, weak bass,, and a poor stereo image. With the advent of multichannel surround sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material. To use the binding-post speaker terminals, unscrew the collar until the pass-through hole in the center post is visible under the collar. Insert the bare end of the wire through this hole; then screw the collar down until the connection is tight. The hole in the center of each collar is intended for use with banana-type connectors.

jbl_speaker_s36ii,_s36-awii_connection_tips.png

jbl_speaker_s36ii,_s36-awii_speaker_connections.png

TROUBLESHOOTING

If there is no sound from any of the speakers:

Check that the receiver/amplifier is on and that a source is playing.
Review the proper operation of your receiver/amplifier.
Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, or punctured.

If the system plays at low volumes but shuts off as volume is increased:

Check all wires and connections between the receiver/amplifier and speakers.
Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, or punctured.
If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier.

If there is no sound coming from one speaker:

Check the “Balance” control on your receiver/amplifier.
Check all wires and connections between the receiver/amplifier and speakers. Make sure no wires are touching other wires or terminals and creating a short circuit.
Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut,, or punctured.
In Dolby Digital or DTS® mode, make sure that the receiver/processor is configured so that the speaker in question is enabled.
Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem is in the same place, i.e., the speaker that was working previously now has no sound, and the speaker that was not working now sounds fine; or whether it has moved, i.e., the speaker that was not working still has no sound, and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner’s manual for that product for further information. If the problem follows the speaker, consult your dealer for further assistance or, if that is not possible, visit our website at www.jbl.com for further information.

Search Manuals in: s36awii

Read More