Introducing the Intex Sand Filter Pump SF80110-1

The Intex Sand is an efficient solution for keeping your above-ground pool water clean and clear. With a powerful flow rate of 2,100 gallons per hour, this pump utilizes sand filtration technology to effectively remove impurities. It features a user-friendly six-function control valve for easy operation, including filtering, backwashing, and draining. Designed for durability and low maintenance, the Intex Sand Filter Pump SF80110-1 is priced at approximately $159.99.

PARTS REFERENCE

Before assembling your product, please take a few minutes to check the contents and become familiar with all the parts.

Parts shown on this page are supplied with the pool package and are shown here for assembly purposes only.

NOTE: Drawings for illustration purposes only. Actual products may vary. Not to scale.
No tools are required for the assembly.
If this pump was not purchased as part of a pool set, the above parts can be ordered at https://www.intexcorp.com if needed.

REF. NO.	DESCRIPTION	QTY.	SPARE PART NO.
REF. NO.	DESCRIPTION	QTY.	SF80110-1	SF70110-1	SF60110-1
1	PRESSURE GAUGE	1	11411	11224	11224
2	6-WAY VALVE	1	11378	11496	11496
3	DRAIN OUTLET COVER	1	11131	11131	11131
4	CLAMP	1	11380	11380	11380
5	TANK O-RING	1	11379	11379	11379
6	SAND SHIELD	1	11382	11382	11382
7	CENTER PIPE HUB	1	11815	11813	11814
8	LATERAL	10	11484	-	-
8	LATERAL	12	-	11384	11384
9	DRAIN VALVE CAP	1	11456	11456	11456
10	DRAIN VALVE O-RING	1	11385	11385	11385
11	L-SHAPE O-RING	4	11228	11228	11228
12	HOSE WITH NUTS	2	11009	11009	11009
13	SAND FILTER INTERCONNECTING HOSE	1	11820	11388	11535
14	LEAF TRAP NUT	1	11822	11479	11479
15	LEAF TRAP O-RING	1	11824	11232	11232
16	BASKET	1	11821	11260	11260
17	FILTER HOUSING NUT	1	11261	11261	11261
18	L-SHAPE O-RING	1	11412	11412	11412
19	AIR RELEASE VALVE/SEDIMENT RELEASEVALVE	2	10460	10460	10460
20	VALVE O-RING	2	10264	10264	10264
21*	PLUNGER VALVE (HOSE O-RING & STEP WASHER INCLUDED)	2	10747	10747	10747
22*	HOSE O-RING	2	10262	10262	10262
23*	STEP WASHER	2	10745	10745	10745
24*	STRAINER NUT	2	10256	10256	10256
25*	FLAT STRAINER RUBBER WASHER	2	10255	10255	10255
26*	THREADED STRAINERCONNECTOR	1	11235	11235	10744
27*	ADJUSTABLE POOL INLET JET NOZZLE	1	12369	12369	12369
28*	ADAPTOR B	2	10722	10722	10722
29*	STRAINER CONNECTOR	1	11070	11070	11070
30*	POOL INLET JET NOZZLE	1	12364	12364	12364
31*	STRAINER GRID	1	11072	11072	11072
32	SCREW	2	11381	11381	11381
33	PUMP MOTOR & CONTROL	1	12491EG	12487EG	12489EG
34	PRE-FILTER ASSEMBLY	1	11826	11371	11371
35	LEAF TRAP COVER	1	11823	11480	11480
36	SAND FILTER PUMP MOTOR INLET O-RING	2	11457	11457	11457
37	SAND FILTER PUMP TANK	1	11804	11802	11803
38	SAND FILTER PUMP TANK BASE	1	11816	11800	11801
39*	AIR JET VALVE	1	12363	12363	12363
40*	STRAINER GRID	1	-	-	10253
41	PRE-FILTER HOUSING	1	12100	12099	12099
42*	INLET THREADED AIR CONNECTOR	1	12371	12372	12372
43*	POOL INLET AIR ADAPTOR	1	12368	12368	12368
44*	INLET STRAINER CONNECTOR	1	12365	12365	12365
45*	AIR JET VALVE CAP (NOT SHOWN)	1	12373	12373	12373

" * ": Optional.
When ordering parts, be sure to quote the model number and part numbers.

Description

The Intex Sand Filter Pump SF80110-1 is built with durability and efficiency in mind. The pump features a robust sand filter tank that is resistant to corrosion, ensuring long-lasting performance. The 0.95 HP motor provides powerful circulation and filtration, while the easy-to-use control valve allows for simple operation and maintenance. The pump also includes a built-in timer for automated operation, making it convenient for pool owners who want a hassle-free maintenance routine.

POOL OUTLET

STRAINER & PLUNGER VALVE SETUP (optional)

The strainer grid prevents large objects from jamming and/or damaging the filter pump. If your pool has an inflatable top ring, install the strainer, nozzle and plunger valve before inflating the pool liner top ring. The part numbers here onward refer to the parts depicted in the Parts List section of this manual. To install, do the following:

In a counter-clockwise motion unscrew plunger valve union from the threaded strainer connector (26) (see drawing 1). Be careful not to lose the step rubber washer (23). Place the plunger valve on the ground in a safe place.
In a counter-clockwise motion unscrew the strainer nut (24) from the threaded connector (26). Leave the flat washer (25) on the connector (26).
Install the strainer and plunger valve at the lower position of pool outlet (marked "+"). From the inside of the pool liner insert the connector (26) into one of the pre-cut holes with the washer remaining on the connector to be placed against the inside of the liner wall.
Before assembly, lubricate the threads with a petroleum jelly. With the flat side of the strainer nut (24) facing the outside wall of the liner in a clockwise motion screw the strainer nut (24) back onto the threaded connector (26) (see drawing 2).
Finger tighten the strainer nut (24) onto the threaded connector (26).
Grasp the plunger valve assembly. Make sure the step washer (23) is in place.
In a clockwise motion screw the plunger valve union back onto the threaded connector (26) (see drawing 3).
In a clockwise motion turn the plunger valve handle to close position. Ensure the plunger valve is securely closed. This will prevent water from flowing out during filling of the pool (see drawing 4).

POOL INLET

NOZZLE & PLUNGER VALVE SETUP (optional)

In a counter-clockwise motion unscrew plunger valve union from the inlet threaded air connector (42) (see drawing 5). Be careful not to lose the step rubber washer (23). Place the plunger valve on the ground in a safe place.
In a counter-clockwise motion unscrew the strainer nut (24) from the inlet threaded air connector (42). Leave the flat washer (25) on the connector (42).
Install the nozzle and plunger valve at the upper position of pool inlet. From the inside of the pool liner insert the nozzle union (27 & 42) into one of the pre-cut holes with the washer remaining on the connector to be placed against the inside of the liner wall.
Before assembly, lubricate the threads with a petroleum jelly. Then, with the flat side of the strainer nut (24) facing the outside wall of the liner in a clockwise motion screw the strainer nut (24) back onto the inlet threaded air connector (42) (see drawing 6).
Finger tighten the adjustable pool inlet jet nozzle (27) and the strainer nut (24) onto the inlet threaded air connector (42).
Grasp the plunger valve assembly. Make sure the step washer (23) is in place.
Screw the air jet valve (39) over the inlet threaded air connector (42). NOTE: Make sure the air jet valve is securely tighten and facing up. In a clockwise motion screw the plunger valve union back onto the inlet threaded air connector (42) (see drawing 7).
In a clockwise motion turn the plunger valve handle to close position. Ensure the plunger valve is securely closed. This will prevent water from flowing out during filling of the pool (see drawing 8).
Adjust the direction of nozzle head pointing away from the pool outlet for a better circulation result
(see drawing 9).
The pool liner is now ready to fill with water. Consult the above-ground-pool owner’s manual for filling instructions.

SPECIFICATIONS

The sand filter removes suspended particles but does not sanitize your pool. Pool chemistry is a specialized area and you should consult your local pool service specialist for details.

Model:	SF80110-1	SF70110-1	SF60110-1
Power:	110-120 Volt AC	110-120 Volt AC	110-120 Volt AC
Amperage:	2.0 A	4.0 A	4.8 A
Maximum working pressure:	2 bar (30 psi)	2 bar (30 psi)	2 bar (30 psi)
Effective filtering area:	0.07 m² (0.79 ft²)	0.1 m² (1.07 ft²)	0.13 m² (1.44 ft²)
Maximum Flow Rate:	6055 LPH (1600 GPH)	8140 LPH (2150 GPH)	9275 LPH (2450 GPH)
Recommended filtering media quantity:	No.20 silica sand 23 Kg (50 Lbs) or glass sand 16 Kg (35 Lbs).	No.20 silica sand 35 Kg (77 Lbs) or glass sand 25 Kg (55 Lbs).	No. 20 silica sand 55 Kg (121 Lbs) or glass sand 38 Kg (84 Lbs).
Recommended filtering media (Not included):	No. 20 silica sand or glass sand. Particle size range 0.45 to 0.85 mm (0.018 to 0.033 inches). Uniformity Coefficient less than 1.75.
Limited Warranty:	see “Limited Warranty”

NOTE: NOT SUITABLE FOR USE WITH KCP-LOW -SALT AUTOMATIC SALTWATER SYSTEM (MODEL 6110/6220).

SETUP INSTRUCTIONS

TOOLS REQUIRED: One (1) Phillips screwdriver

Pump location and mounting:

The system must be installed on a solid level and vibration-free base.
Provide a location protected from the weather, moisture, flooding and freezing temperature.
Provide adequate access, space and lighting for routine maintenance.
The pump motor requires free circulation of air for cooling. Do not install the pump in a damp or non-ventilated location.

A team of 2 or more people is recommended for setting up this product.

Motor pre-filtering assembly setup

Remove the sand filter and its accessories from the packaging carefully and inspect for any visible damage. For missing or damaged parts contact the appropriate Intex Service Center listed in the separate “Authorized service Centers” sheet.
In a counter-clockwise motion unscrew the leaf trap cover (14) from the pre-filter housing. Take out the basket (16) and filter housing nut (17) (see drawing 10).
Connect the pre-filter housing to the motor water inlet. Note: Align the connector in the pre-filter housing with the water inlet on the motor (see drawing 11).
In a clockwise motion screw filter housing nut (17) onto the motor water inlet (see drawings 12.1 & 12.2).
Replace the basket (16) and leaf trap cover (14) back to the pre-filter housing (see drawings 13.1 & 13.2).

Sand tank installation

Place the tank support base on the selected location.
Place the tank on the tank support base (see drawing 14.1).
Connect the motor pre-filtering assembly unit to the tank support base (see drawing 14.2).
NOTE: Ensure the pre-filter housing water inlet hose connection is facing towards the pool.
IMPORTANT: Some countries, especially in the European community, require the product to be secured to the ground or to a base in a permanent upright position. Check your local authorities to determine if there is a regulation in your area regarding above-the-ground swimming pool filter-pumps. If yes, then the product can be mounted to a platform using the two holes located in the base. See drawing 14.3.
The product can be mounted on a cement base or onto a wooden plat form to prevent accidental falling over.
- The mounting holes are 6.4 mm in diameter and spaced 100 mm for model SF80110-1 (spaced 115 mm for model SF70110-1 & SF60110-1) apart.
- Use two bolts and lock nuts with a maximum of 6.4 mm in diameter.

Sand loading

IMPORTANT: Use No. 20 silica sand or glass sand with particle size range 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75.
NOTE: Before loading the tank with sand, ensure the center pipe hub assembly is securely in place at the bottom of the tank, and vertically centered inside the tank.

Place the sand shield (6) over the top of the center pipe. Pour the sand into the tank at a slow rate (see drawing 15).
Fill the tank approximately half way, remove the sand shield (6) from the top (see drawing 16).
Evenly distribute the sand inside the tank, then fill the tank with some water to provide a cushioning effect when the remaining sand is poured in. This prevents the center pipe hub (7) from excessive shock (see drawing 17). Place the sand shield (6) back and continue to pour the sand into the tank.
Sand shall be filled between the “MAX” and “MIN” marked gauge on the center pipe. Evenly spread and level out the sand by hand (see drawings 17 & 18).
Remove the sand shield (6).
Wash away all sand around the top edge of the tank.

WARNING

Improper tank valve and clamp assembly could cause the valve and clamp to blow off and cause serious injury, property damage or death.

6-way valve installation

Lower the 6-way valve over the tank slowly, and ensure the bypass pipe protruding underneath the 6-way valve fits securely into the center pipe hub (7) top opening (see drawing 19).
IMPORTANT: There are three hose connection ports on the 6-way valve, ensure the outlet connection (from filter to the pool) on the valve is facing towards the pool, and the inlet connection (from motor to valve) is aligned with the motor outlet (see drawing 20).
Place an L-shape o-ring (11) on the 6-way valve inlet connection and on the pump motor outlet. In a clockwise motion connect the sand filter interconnecting hose (13) between the pump motor outlet and the 6-way valve inlet connection (see drawing 21).
Remove the clamp bolt, and install the clamp around the tank and 6-way valve flanges, then replace the clamp bolt and use a phillips screwdriver (not included) to tighten it (see drawing 22).

SAND FILTER PUMP HOSE CONNECTION SETUP

WARNING: Position this product away from the pool, so as to prevent children from climbing on it and accessing the pool.

The 6-way valve has three hose connection ports.

Connect one hose (12) end to the pre-filter inlet and the other end of the hose to the lower plunger valve with the strainer. Ensure the hose nuts are securely tightened.
Connect the second hose (12) between the 6-way valve water outlet and the upper plunger valve with the inlet-nozzle. Ensure the hose nuts are securely tighten.
The third hose connection port (drain/waste outlet) on the 6-way valve shall be directed to a proper draining receptacle using a hose or pipe (not provided). Remove the drain cap before attaching the drain/waste hose or pipe.
The sand filter pump is now ready to filter the pool.

sand_filter_pump_hose_connection_setup_intex_sand_filter_pump_sf80110-1.png

For Pools with Dual Suction Outlets Configuration:
In order to comply with the requirement of the Virginia Grahame Baker Act (for USA and Canada), your pool is designed with dual suction outlets and one inlet fittings. Parts in grey highlight on this page are supplied with the pool set package and are shown here for assembly purposes only. If this pump was purchased as part of a pool set, refer to the pool owner’s manual for more details.

for_pools_with_dual_suction_outlets_configuration_intex_sand_filter_pump_sf80110-1.png

For NON-INTEX pool:
Connect the hose (12) to the pool inlet/outlet connection with a large hose clamp. Tighten securely.

For INTEX pool with 1-1/4” (32mm) connections/hoses:
Make sure the air jet valve (39) is securely tighten onto the pool inlet air adaptor (43) and facing up.

for_intex_pool_with_1-1-4â_(32mm)_connections-hoses_intex_sand_filter_pump_sf80110-1.png

OPERATING INSTRUCTIONS

WARNING

Risk of electric shock. Connect this product only to a grounding type receptacle protected by a ground-fault circuit interrupter (GFCI) or residual current device (RCD). Contact a qualified electrician if you cannot verify that the receptacle is protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD, which has a maximum rate of 30 mA. Do not use a portable residual current device (PRCD).
To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter plugs to connect unit to electric supply; provide a properly located outlet.
Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
Never operate this product above the maximum working pressure stated on the filter tank.
Always switch off pump before changing the 6-way valve position.
Operating this product without water flowing through the system can cause a build up of hazardous pressure which can result in an explosive situation, serious injury, property damage or death.
Never test this pump with compressed air. Never operate the system with water temperature above 35°C (95°F).

6-way valve positions and function

Valve Position

Function

Water Flow Direction

FILTER

(see drawing 23)

Normal filtration andregular vacuuming of pool

From pump throughfilter media to pool

BACKWASH

(see drawing 24)

Reverses water flow to clean filter

media

From pump through filtermedia to

valve waste/drain outlet

RINSE

(see drawing 25)

For initial startup cleaning of the sand, and

leveling the sandbed afterbackwashing

From pump through filtermedia to

valve waste/drain outlet

WASTE

(see drawing 26)

For vacuuming directly to waste, loweringpool level or to drainthe pool

From pump to valve waste/drain outlet bypassing the filter media

RECIRCULATE

(see drawing27)

For circulating waterback to pool without goingthrough the filtermedia

From pump throughvalve to pool bypassing the filter media

CLOSED

(see drawing 28)

Shuts off all flow to filter and pool

“Do not use this setting with pump running”

6-way_valve_positions_and_function_intex_sand_filter_pump_sf80110-1.png

Initial startup and operation

Before operating, be sure that:

All the hoses have been connected and tightened securely, and correct amount of filter sand have been loaded.
The entire system is connected to a grounding type receptacle protected by a ground-fault circuit interrupter (GFCI) or residual current device (RCD).

CAUTION: The filter control valve has a closed position. The pump should never be on when the valve is in the closed position. If the pump is operated with the valve closed, explosive situation could exist.

Turn both plunger valve handles fully counter-clockwise until they stop. This opens the valves to allow water to flow into the sand filter pump. With water flowing into sand filter pump, the water pressure will allow the air trapped inside to escape from the air release valves (19). When all the air has escaped water will flow out of the valves (19). When this occurs gently finger tighten the valves (19) in a clockwise direction.
Ensure the drain/waste outlet on the 6-way valve is not covered and directed to a proper draining receptacle.
Ensure the pump is off, depress the 6-way valve and turn 2 it to the “BACKWASH” position (see drawings 24 & 29).
IMPORTANT: To prevent damage to the 6-way valve, always depress the valve handle before turning.Always switch off pump before changing the 6-way valve position.
Switch on the pump (see drawing 30). Water is circulating backward through the sand media and to waste/drain outlet. Backwash until a clear flow of water is observed in the waste/drain outlet or through the drain sediment window.
NOTE: The initial backwash of the filter is recommended to remove any impurities or fine sand particles in the sand media.
Switch off the pump, change the 6-way valve to “RINSE” position (see drawing 25).
Switch on the pump and run the pump for about one minute to level out the sand bed after backwashing the sand media.
Switch off the pump, change the 6-way valve to “FILTER” position (see drawing 23).
Switch on the pump. The system is now operating in the normal filtering mode. Run the pump until the desired pool water clearance is obtained and no more than 12 hours per day.
Record the initial pressure gauge reading when the filter media is clean.

NOTE: During initial setup of the system, it may be necessary to backwash frequently due to unusual heavy dirt present in the water and sand. After that, as the filter removes dirt and impurities from the pool water, the accumulated dirt in the sand media will cause the pressure to rise and the flow to diminish. If there is no vacuuming device attached to the system and the pressure gauge reading is in the yellow zone it is time to backwash the sand media, see “BACKWASH” under “initial startup and operation” section. Vacuuming device (i.e. Intex auto pool cleaner) attached to the system may also cause the flow to diminish and the pressure to rise. Remove any vacuuming device from the system and check if the pressure gauge reading has dropped from the yellow zone to the green zone.

Operating the system under “TIMER” mode or manually:

To operate the sand filter pump in “FILTER” mode under “TIMER” control:

Set the timer dial to the desired operating hours. See operation time table (see drawing 31).
Turn on the pump by pressing the switch to “ ” position, the sand filter pump is now filtering the water and will stop after the operating hours are completed. The built-in timer will now operate for the number of hours selected at the same time each day.
Operating hours can be re-adjusted if necessary. Follow step A – B.

To operate the sand filter pump manually (without the “TIMER” mode):

Turn on the pump by pressing the switch to “-” position, the sand filter pump is now filtering the water.
To turn off the pump, press the switch to “O” position.

IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service Department for assistance. See separate “Authorized Service Centers” sheet.

INTEX POOLS OPERATING TIME TABLE (WITHOUT INTEX SALTWATER SYSTEM)

This table shows the required operating time for average use of the sand filter pump with above ground pools. If the system is attached to an “Intex Saltwater System” unit, the filter pump running time should be longer than the required operating time of the Intex Saltwater System unit.

Pool Size		Water Capacity (Calculated at 90% for Frame Pool and 80% for Easy Set & Oval Pool)		Sand filter pump operating time (For one cycle) / (Hours)
Pool Size		(Gals)	(Liters)	SF80110-1	SF70110-1	SF60110-1
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET® POOL	457cmx84cm (15'x33")	2587	9792	2	-	-
	457cmx91cm (15'x36")	2822	10681	2	-	-
	457cmx107cm (15'x42")	3284	12430	2	-	-
	457cmx122cm (15'x48")	3736	14141	4	-	-
	488cmx107cm (16'x42")	3754	14209	4	-	-
	488cmx122cm (16'x48")	4273	16173	4	-	-
	488cmx132cm (16'x52")	4614	17464	4	-	-
	549cmx107cm (18'x42")	4786	18115	4	2	2
	549cmx122cm (18'x48")	5455	20647	4	2	2
ROUND METAL FRAME POOL	457cmx91cm (15'x36")	3282	12422	2	-	-
	457cmx107cm (15'x42")	3861	14614	4	-	-
	457cmx122cm (15'x48")	4440	16805	4	-	-
	488cmx122cm (16'x48")	5061	19156	4	-	-
	549cmx122cm (18'x48")	6423	24311	6	4	4
	640cmx132cm (21'x52")	9533	36082	6	4	4
	732cmx132cm (24'x52")	12481	47241	8	6	6
ULTRA FRAME POOL	488cmx122cm (16'x48")	5061	19156	4	-	-
	549cmx122cm (18'x48")	6423	24311	4	4	4
	549cmx132cm (18'x52")	6981	26423	6	4	4
	610cmx122cm (20'x48")	7947	30079	6	4	4
	671cmx132cm (22'x52")	10472	39637	8	4	4
	732cmx132cm (24'x52")	12481	47241	8	6	6
	792cmx132cm (26'x52")	14667	55515	12	8	8
GRAPHITE GRAY PANEL POOL SET™	478cmx124cm (15'8"x49")	4440	16805	4	-	-
	508cmx124cm (16'8"x49")	5061	19156	4	4	2
	569cmx135cm (18'8"x53")	6981	26423	6	4	4
OVAL FRAME POOL	305cmx549cmx107cm (10'x18'x42")	2885	10920	2	-	-
OVAL FRAME POOL	366cmx610cmx122cm (12'x20'x48")	4393	16628	4	2	2
RECT.ULTRA FRAME POOL	274cmx457cmx122cm (9'x15'x48")	3484	13187	4	2	2
	274cmx549cmx132cm (9'x18'x52")	4545	17203	4	2	2
	305cmx610cmx132cm (10'x20'x52")	5835	22085	4	4	2
	366cmx732cmx132cm (12'x24'x52")	8403	31805	6	4	4
	488cmx975cmx132cm (16'x32'x52")	14364	54368	12	8	6

NOTE: The “12” hours timer setting position has an additional 20 minutes over the actual setting.

NON-INTEX POOLS OPERATING TIME TABLE

This table shows the required operating time for average use of the sand filter pump with above ground pools.

Pool Size		Water Capacity (Calculated at 90% for Frame Pool and 80% for Easy Set & Oval Pool)		Sand filter pump operating time (For one cycle) / (Hours)
Pool Size		(Gals)	(Liters)	SF80110-1	SF70110-1	SF60110-1
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET® POOL	457cmx84cm (15'x33")	2587	9792	2	-	-
	457cmx91cm (15'x36")	2822	10681	2	-	-
	457cmx107cm (15'x42")	3284	12430	2	-	-
	457cmx122cm (15'x48")	3736	14141	4	-	-
	488cmx107cm (16'x42")	3754	14209	4	-	-
	488cmx122cm (16'x48")	4273	16173	4	-	-
	488cmx132cm (16'x52")	4614	17464	4	-	-
	549cmx107cm (18'x42")	4786	18115	4	2	2
	549cmx122cm (18'x48")	5455	20647	4	2	2
ROUND METAL FRAME POOL	457cmx91cm (15'x36")	3282	12422	2	-	-
	457cmx107cm (15'x42")	3861	14614	4	-	-
	457cmx122cm (15'x48")	4440	16805	4	-	-
	488cmx122cm (16'x48")	5061	19156	4	-	-
	549cmx122cm (18'x48")	6423	24311	6	4	4
	640cmx132cm (21'x52")	9533	36082	6	4	4
	732cmx132cm (24'x52")	12481	47241	8	6	6
ULTRA FRAME POOL	488cmx122cm (16'x48")	5061	19156	4	-	-
	549cmx122cm (18'x48")	6423	24311	4	4	4
	549cmx132cm (18'x52")	6981	26423	6	4	4
	610cmx122cm (20'x48")	7947	30079	6	4	4
	671cmx132cm (22'x52")	10472	39637	8	4	4
	732cmx132cm (24'x52")	12481	47241	8	6	6
	792cmx132cm (26'x52")	14667	55515	12	8	8
GRAPHITE GRAY PANEL POOL SET™	478cmx124cm (15'8"x49")	4440	16805	4	-	-
	508cmx124cm (16'8"x49")	5061	19156	4	4	2
	569cmx135cm (18'8"x53")	6981	26423	6	4	4
OVAL FRAME POOL	305cmx549cmx107cm (10'x18'x42")	2885	10920	2	-	-
OVAL FRAME POOL	366cmx610cmx122cm (12'x20'x48")	4393	16628	4	2	2
RECT.ULTRA FRAME POOL	274cmx457cmx122cm (9'x15'x48")	3484	13187	4	2	2
	274cmx549cmx132cm (9'x18'x52")	4545	17203	4	2	2
	305cmx610cmx132cm (10'x20'x52")	5835	22085	4	4	2
	366cmx732cmx132cm (12'x24'x52")	8403	31805	6	4	4
	488cmx975cmx132cm (16'x32'x52")	14364	54368	12	8	6

MOTORCYCLE PRE-FILTER CLEANING AND MAINTENANCE

Make sure the filter pump is turned off, then unplug the power cord from the electrical outlet.
Turn both plunger valve handles fully clockwise until they stop. This closes the valves, preventing water from flowing out of the pool.
Release the pressure first by opening the sediment release valve (19) located on the bottom side of the pre-filter housing (see figure 32).
In a counter-clockwise motion unscrew the leaf trap cover (14), then remove the basket (16) and leaf trap o-ring (15) from the pre-filter housing (see drawing 33).
Empty and flush the basket using a garden hose, you can use a plastic brush to remove sediment from the basket. Do not use metal brushes.
Clean and rinse the inside of the pre-filter container and leaf trap O-ring with a garden hose.
Reinstall the leaf trap O-ring, basket and leaf trap cover into the pre-filter housing.
Close the sediment release valve (19) again.

POOL CARE & CHEMICALS

All pools require maintenance to keep their water clear and hygienic. With proper chemical control, your filter will help achieve this goal. Consult your pool supply dealer for instructions on the proper use of chlorine, algaecide, and other chemicals necessary for sparkling clear water.
Keep pool chemicals away from children.
Do not add chemicals to the pool while it is filling. Skin or eye irritation may occur.
Daily pH checking and chemical maintenance of the water are essential and cannot be overemphasized. Chlorine, algaecide, and maintenance of proper pH levels are necessary when filling the pool as well as throughout the season. Consult your local pool supply store for instructions.
The first filling of the pool season may have brackish water that requires additional water additions and additional filtration time. Do not allow swimming in the pool until the pH level is balanced. Consult your local pool supply store for instructions.
Chlorinated water can damage grass, gardens, or shrubs when children play in the pool and splash water out of the pool. The grass area under the pond liner will be destroyed. Note that some types of grass can grow through the liner.
Filter run times vary depending on pool size, weather, and usage levels. Experiment with different run times to produce clear, clean water.

CAUTION
Concentrated chlorine solutions can damage pool liners. Always follow chemical manufacturer's instructions, as well as health and hazard warnings.

LONG TERM STORAGE & WINTERIZATION

CAUTION
Allowing water to freeze will damage the sand filter and void the warranty. If an antifreeze solution is necessary, use only propylene glycol. Propylene glycol is non-toxic and will not damage plastic system components; other antifreezes are very toxic and can damage plastic components in the system.

Before emptying your pool for long-term storage, or relocation, make sure the water is directed to an acceptable drain away from the house. Check local regulations for specific instructions regarding pool water disposal.
Turn off the unit, and unplug the power cord from the wall outlet.
When the pool is empty, disconnect all hoses from the pump and plunger valve and remove the strainer/plunger valve from the pool wall.
In a counterclockwise motion, unscrew the drain valve (9) from the drain valve to drain the tank completely. The drain valve is located at the bottom of the filter tank.
Remove the pump motor from the bottom of the tank.
Leave the sand filter pump pieces and hose outside until completely dry.
Coat the following o-rings and washers with petroleum jelly for long-term storage:
- L-shaped O-ring (11 & 18).
- Pump hose O-ring (22).
- Step washer filter valve assembly (23).
- Flat filter rubber washer (25).
Press the 6-way valve handle and turn it to set the pointer to the top “N” position of the valve.
This allows water to flow from the valve. Leave the 6-way valve in this off position.
It is best to place all dry parts and pump motors in their original packaging for storage. To avoid condensation or corrosion problems, do not cover or wrap the pump motor with plastic bags.
Store the pump motor and accessories in a dry place. The storage temperature should be controlled, between 0 degrees Celsius (32 degrees Fahrenheit) and 40 degrees Celsius (104 degrees Fahrenheit).

IMPORTANT SAFETY RULES

Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.

READ AND FOLLOW ALL INSTRUCTIONS

To reduce the risk of injury, do not permit children to use this product. Always supervise children and those with disabilities.
Children must stay away from this product and electrical cord(s).
Assembly and disassembly by adults only.
Risk of electric shock. Connect only to a grounding-type receptacle, this product is provided with a ground-fault circuit interrupter. If replacement of the plug or cord is needed, use only identical replacement parts.
Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment to the product.
The unit is provided with a ground-fault circuit interrupter (GFCI). To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button, power should be restored. If the GFCI fails to operate in this manner. The GFCI is defective. If the GFCI interrupts power to the pump without the test button being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump and have the problem corrected by a qualified service representative before using.
Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge trimmers and other equipment.
To reduce the risk of electric shock, replace damaged cord immediately. Use a qualified electrician to replace the cord.
To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter plugs to connect unit to electric supply; provide a properly located outlet.
Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
Do not use an appliance leakage current interrupter (ALCI) in place of a GFCI since the ALCI will not protect people.
Position this product away from pool, so as to prevent children from climbing on it and access the pool.
Do not operate this product when pool is occupied.
To reduce the risk of entrapment hazard, never enter the pool if suction strainer component is loose, broken, cracked, damaged or missing. Replace loose, broken, damaged, cracked or missing suction strainer components immediately.
Never play or swim near suction fittings. Your body or hair may be trapped causing permanent injury or drowning.
To prevent equipment damage and risk of injury, always turn pump off before changing the filter control valve position.
Never operate this product above the maximum working pressure stated on the filter tank.
Hazardous Pressure. Improper tank valve cover assembly could cause the valve cover to blow off and cause serious injury, property damage or death.
This product is intended to be used only for the purposes described in the manual!

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR OTHER SERIOUS INJURY OR DEATH.

CAUTION

This product is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.

To reduce the risk of electric shock the pool must be installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place portable appliances closer than 5 feet (1.5 m) from the pool. These product warnings, instructions and safety rules provided with the product represent some common risks of water recreation devices and do not cover all instances of risk and danger. Please use common sense and good judgement when enjoying any water activity.

SAVE THESE INSTRUCTIONS

TROUBLESHOOTING GUIDE

TROUBLE	CAUSE	SOLUTION
FILTER MOTOR FAILS TO START	The motoris not pluggedin. The GFCI/RCD circuit breaker is tripped. Motor toohot and overload protection is shut off.	Line cord must be plugged into a 3 wire outlet that is protected by a Class A Ground Fault Circuit Interrupter, or RCD. Reset circuit breaker. If circuit breaker trips repeatedly,your electrical system may have a defect. Turn off circuit breakerand call an electrician to correct the problem. Let the motor cool down and restart again.
FILTER DOESN’T CLEAN POOL	Improper chlorineor pH levels. No filtering media in tank. Wrong 6-way valve settingposition. Excessively dirtypool. The strainer screen is restricting the water flow.	Adjust the chlorine and pH level. Consult your local swimming poolsupply stores. Load with filter sand, see “sand loading instructions”. Set valve to “FILTER” position. Operate the filter for longer periods. Clean the strainer screen at the inlet.
FILTER DOESN’T PUMP WATER OR FLOW IS VERY SLOW	Clogged inlet or discharge. An air leak on the intakeline. Excessively dirtypool. Sand media clogged with dirt. Nozzle and strainer connections are reversed. Crusting or caking on the filtering sand surface. Pool vacuuming device attached to the system. Inlet threaded air connector connected to thewrong hole on the liner.	Clear any obstructions in the intake hose by discharging it inside pool wall. Tighten hose nuts, check hoses for damage, check pool water level. Clean the pre-filtering basket more often. Backwash filter. Install the nozzle at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet. Remove about 1” of sand if necessary. Remove any pool vacuuming device attached to the system line. Make sure the inlet threaded air connector is connected to the pool inlet upperhole.
PUMP DOESN’T WORK	Low water level. Strainer screenclogged up. An air leak on the intakehose. Faulty motoror the impeller is jammed.	Fill pool to correctwater level. Clean strainer screens at pool inlet. Tighten hose nuts, checkhose for damage. Contact Intex service center.
6-WAY VALVE/ COVER LEAKING	Sand tank o-ring missing. Sand tank o-ring dirty. Flange clamp not tight. 6-way valvedamage.	Remove 6-way valve cover and ensure the o-ring is in place. Clean sand tank o-ring with garden hose water. Tighten the clamp with wrench supplied. Contact Intex service center.
HOSE LEAKING	Hose nut not securely tight. Hose connection fitting o-ring/L-shape o-ringmissing.	Tighten/reinstall hose nut. Ensure o-ring/L-shape o-ring is in place and not damaged.
TIMER IS INACCURATE OR TIMER CAN'TBE SET	Possible inner timer defective.	Turn off the pump and restart5 minutes later. Re-set the timer. Contact Intex service center.
PRESSURE GAUGE DOESN’T WORK	Clogged inlet of the pressure gauge. Pressure gaugedamage.	Clear any obstructions in the intake by unscrewing it from the 6-way valve. Contact Intex service center.
SAND IS FLOWING BACK INTO THE POOL	Sand is too small. Sand bed is calcified.	Use only No. 20 silica sand with particle size range 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. Change sand.
INLET THREADED AIR CONNECTOR /AIR JET VALVE LEAKING	Plunger valve not well-fitted. Air jetvalve is nottight and facing up. Air jet valve internal seal blocked. Air jet valve internal seal dirty. Air jet valve broken.	Tighten or reinstall plungervalve. Tighten air jet valve and make sure it’s facing up. Turn pump ON and run for few seconds, then turn OFF, repeat 3 times. Remove air jet valve, flush dirt out with water and replace valve back. Replace a new air jet valve.

COMMON POOL PROBLEMS

PROBLEM	DESCRIPTION	CAUSE	SOLUTION
ALGAE	Greenish water. Green or black spots on pool liner. Pool liner is slippery and/or has a bad odor.	Chlorine andpH levels need adjustment.	Super chlorinate with shock treatment. Correct pH to your pool store's recommended level. Vacuum pool bottom. Maintain properchlorine level.
COLORED WATER	Water turnsblue, brown, or black when first treated with chlorine.	Copper, ironor maganese in water being oxidized by the added chlorine. This is Common.	Adjust pH level to the recommended level. Run filter untilwater is clear.
FLOATING MATTER IN WATER	Water is cloudy or milky.	"Hard water" caused by a too high pH level. Chlorine contentis low. Foreign matterin water.	Correct thepH level. Check with your pool dealer for advice. Adjust the chlorine level.
CHRONIC LOWWATER LEVEL	Level is lower thanon previous day.	Rip or hole in pool lineror hoses. The drain valves are loose.	Repair with a patch kit. Finger tighten all caps.
SEDIMENT ON POOL BOTTOM	Dirt or sand on pool floor.	Heavy use,getting in and out of pool.	Use Intexpool vacuum to clean bottom of pool.
SURFACE DEBRIS	Leaves, insects etc.	Pool too close to trees.	Use Intex pool skimmer.

WARRANTY

Your Sand Filter Pump has been manufactured using high quality materials and workmanship. All Intex products are inspected and found to be free from defects before leaving the factory. This Limited Warranty applies only to the Sand Filter Pump and accessories listed below.
The terms of this Limited Warranty apply only to the original purchaser and are not transferable. This Limited Warranty is valid for the period stated below from the date of original retail purchase. Keep your original sales receipt with this manual, as proof of purchase will be required and must accompany any warranty claim or the Limited Warranty is void.

Sand Filter Pump Warranty – 2 Years
Hose, Plunger Valve & Fittings Warranty – 180 days

Pros & Cons

Pros

Efficient Filtration: Effectively removes dirt and debris from the pool water.
Durable Construction: Built with corrosion-resistant materials for long-lasting use.
Easy Operation: Simple control valve and built-in timer for automated operation.
Value for Money: Offers great performance at an affordable price.

Cons

Noisy Operation: Some users have reported that the pump can be noisy during operation.
Heavy Weight: The pump is quite heavy, making it difficult to move around.
Complex Assembly: Some users find the assembly process challenging.

Customer Reviews

Customers have generally praised the Intex Sand Filter Pump SF80110-1 for its effective filtration and durable construction. Many reviewers have noted that it significantly improves the clarity of their pool water. However, some have mentioned that it can be noisy and heavy. Common complaints include issues with assembly and occasional leaks, but overall, the product is well-regarded for its performance.

Search Manuals in: sf80110-1

Read More