JBL Speaker JRX215

Introduction

The JBL Speaker JRX215 is a powerful and versatile speaker that delivers high-quality sound for various applications. Whether you're a musician, DJ, or audio enthusiast, this speaker is designed to enhance your audio experience.

Instructions

Connect the JBL Speaker JRX215 to a power source using the provided power cable.
Ensure that the power switch is in the "Off" position before connecting any audio sources.
Connect your audio source, such as a mixer or amplifier, to the speaker using an appropriate audio cable.
Adjust the volume and other settings on your audio source to the desired levels.
Turn on the power switch of the JBL Speaker JRX215.
Enjoy the high-quality sound produced by the speaker.

SPECIFICATIONS

ACOUSTIC & ELECTRICAL SPECIFICATIONS

Nominal Impedance: 8 Ohms
Power Capacity: 250W, 1000W Peak Power Capacity
Frequency Response (±3 dB): 59 Hz – 13 kHz
Frequency Range (–10 dB): 41 Hz – 18 kHz
Maximum SPL: 129 dB
Crossover Frequency: 2.2 kHz

SYSTEM COMPONENTS

Cabinet: Enclosure (Not For Sale)
Grille: 5033398
Low Frequency Driver: M115-8A, 380 mm (15 in.) Cone Transducer
D.C. Resistance: 5.3 ohms
High Frequency Driver: 2414H-C, 25 mm (1 in) exit compression driver mounted on Progressive, Transition™ Waveguide
D.C. Resistance: 4.80 ohm +/- 0.2 ohm

AURAL SWEEP TEST SPECIFICATIONS

System Aural Sweep Test: 7.0V Input, 40 Hz to 20 kHz
L.F. Aural Sweep Test: 6.0V Input, 20 Hz to 200 Hz
H.F. Aural Sweep Test: 0.75V Input, 500 Hz to 1.5 kHz

PHYSICAL SPECIFICATIONS

Enclosure Dimensions: 699 mm x 460 mm x 432 mm (27.5 in x 18.1 in x 17 in)
Net Weight: 27.4 kg (60.5 lb)

WARRANTY INFORMATION:

Refer to the Warranty Statement posted online

PACKAGE

Quick set-up Guide: 5034639
Carton: 5034637
Filler (2): 339021-001
Micro-foam (4): 49790P
Insert (1): 445549-001

WIRING DIAGRAM

COMPONENT EXPLODED VIEW

COMPONENT PARTS LIST

Item	Part No.	Qty	Description	Item	Part No.	Qty	Description
2	124-67001-01X	1	M115-8A WOOFER	10	5007401	1	LOGO BADGE
3	5000169X	1	M/I, 2414H-C	14	729-90001-16	4	SCR, #12X1,THR FORMING, FLTHD, PH, TY
4	5033398	1	GRILLE	15	882-51110-12	6	SCR, 6 X 3/4,OV,PH,PTCL,BLK ZC,LCS
5	338800-001	1	HORN	19	883-41110-16	16	SCR,8 X 1,PAN,PH,PB,BLK ZINC,LCS
6	5034705	1	NETWORK ASSY,	24	883-41110-12	22	SCR,8 X 3/4,PAN,PH,PB,BLK ZINC,LCS
7	339018-003	2	HANDLE ASSY, WITHOUT LABEL	25	884-41110-16	6	SCR,10 X 1,PAN,PH,PB,BLK ZINC,LCS
8	351256-001	1	CUP, DUAL POLE
9	924-00002-01	4	FOOT

NETWORK SCHEMATIC 5034705

Troubleshooting guide

Basic Checks

Before diving into deeper issues, confirm the basics:

Power and Signal Path

The JRX215 is a passive speaker, meaning it has no built-in amplifier.
Ensure it’s powered by a proper external power amplifier.
Verify the amplifier is turned on and not in protection mode.
Check that signal cables (XLR, ¼", Speakon) are properly connected and undamaged.
Test your source (mixer, phone, etc.) by connecting it to a known working system.

Check Speaker Connections

Use a multimeter to check the speaker cable continuity.
Ensure you’re using speaker cables, not instrument cables — they look similar but behave differently.
Make sure the Speakon connectors are firmly locked in place.

Amplifier Output Matching

The JRX215 is rated:
- 250W continuous / 1000W peak @ 8Ω
Match your amplifier to deliver roughly 250–500W per channel at 8Ω.
Too little power can cause clipping and distortion; too much can blow the driver.

Sound Issues

No Sound

Check that your amp channel is active (not muted or bridged incorrectly).
Try connecting a different speaker to confirm whether the problem is with the amp or the JRX215.
Inspect the input jack plate on the speaker for loose connections.

Low Volume

Check for polarity reversal (wires swapped +/−) — it can cause phase cancellation.
Verify amp gain and mixer output levels.
Ensure EQ or crossover settings are not cutting frequencies.

Distortion

Check for amp clipping (watch the clip indicators).
Replace or test with a different cable.
Try lowering the gain; overdriven signal can damage components.

Physical Inspection

Unplug everything and carefully check:

Woofer cone for tears, rubbing, or burns.
Horn driver for continuity (you can use a multimeter; typical diaphragm = 6–8Ω).
Crossover network inside the cabinet for burnt components.

Component Testing

If you’re comfortable with electronics:

Remove the woofer and test DC resistance with a multimeter:
- Should read around 6–8Ω (for an 8Ω driver).
If it reads open circuit (∞), the voice coil is likely blown.
If resistance is too low (<2Ω), it may be shorted.
Repeat for the HF compression driver.

Common Failures

Symptom	Possible Cause	Fix
No sound	Blown woofer or HF driver	Replace driver
Crackling or intermittent	Loose terminal / bad cable	Tighten or replace
Weak highs	HF diaphragm blown	Replace diaphragm
Weak lows	Woofer damage or polarity issue	Rewire or replace
Amp protection trips	Shorted cable or driver	Check wiring & impedance

Replacement Parts

Typical JBL JRX215 components:

Woofer: JBL 15" 2032H or equivalent.
Horn Driver: JBL 2414H-C.
Crossover: Passive 2-way network (available from JBL parts or authorized dealers).

When to Seek Service

If:

Both drivers test okay, but no sound.
You notice a burnt smell or discoloration inside.
Crossover appears damaged.

→ Take it to an authorized JBL service center. They can test the components and replace only what’s needed.

Search Manuals in: speaker-jrx215

Read More