Setup: Xpo Tool 62552 Electric Impact Driver User Manual

Overview

The 62552 Electric Impact Driver is a corded power tool for driving and loosening screws, bolts, and suitably sized nuts. Its impact mechanism delivers high rotational force for pre-assembly work, making it useful for workshop, repair, vehicle, and general maintenance tasks.

This electric impact wrench operates from a mains power supply and runs at a fixed maximum speed when the trigger is pressed. Use it with the supplied sockets or compatible accessories that match the square drive. For final tightening, always use a correctly adjusted torque wrench rather than relying on the impact driver alone.

Specifications

• Model: 62552
• Power supply: 230 V AC
• Frequency: 50 Hz
• Nominal power: 450 W
• No-load speed: 3,600 revolutions per minute
• Maximum clockwise torque: 100 Nm
• Maximum counter-clockwise torque: 320 Nm
• Square drive: 12.7 mm, or 1/2 inch
• Included impact sockets: 17 mm, 19 mm, 21 mm, and 22 mm
• Weight: 2.1 kg
• Power cable length: 3 m
• Protection class: II

Detailed Description

The tool transfers motor power through a square-drive impact mechanism. When the motor reaches operating speed, the mechanism produces repeated rotational impacts that help loosen tight fasteners and install bolts or nuts efficiently.

The 12.7 mm square drive accepts the included impact sockets. Select a socket that fully fits the fastener and push it securely onto the drive before operating the tool. Do not use damaged, cracked, incorrectly sized, or unsuitable attachments.

A direction switch changes the rotation between clockwise and counter-clockwise operation. Clockwise rotation is intended for tightening and is limited to 100 Nm, while counter-clockwise rotation provides up to 320 Nm for loosening. The reaction torque can be considerable, so hold the tool firmly with both hands when necessary and keep a stable stance.

Safety

Work Area

• Keep the work area clean, organized, and well lit.
• Do not use the impact driver near flammable liquids, gases, or combustible dust.
• Keep children and bystanders away while the tool is running.

Electrical Safety

• Connect the tool only to a supply that matches the voltage shown on its rating plate.
• Do not modify the plug or use unsuitable adapter plugs.
• Keep the power cable away from heat, oil, sharp edges, and moving parts.
• Never carry, pull, or unplug the tool by its cable.
• Do not expose the impact driver to rain or water.
• For outdoor use, use an extension cable designed for outdoor conditions.
• In damp environments, use a protected power supply with residual-current protection.
• Stop using the tool immediately if the cable becomes damaged. Do not touch the damaged section.

Personal Protection

• Stay alert and do not operate the tool when tired or under the influence of alcohol, drugs, or medication.
• Wear safety glasses, work gloves, non-slip safety footwear, and suitable respiratory protection when dust may be produced.
• Tie back long hair and avoid loose clothing or jewelry that could catch in moving parts.
• Keep a balanced stance and avoid overreaching.
• Secure the workpiece with clamps or a vice instead of holding it by hand.

Safe Tool Use

• Use the correct socket or attachment for the fastener and the tool.
• Do not use the impact driver if the switch does not operate correctly.
• Disconnect the plug before changing sockets, making adjustments, or storing the tool.
• Wait until the drive has stopped completely before setting the tool down.
• Keep the tool away from children and untrained users.
• Have damaged equipment repaired by qualified personnel using original replacement parts.
• Hold the tool only by insulated gripping surfaces when the accessory could contact hidden wiring.
• Use the additional handle supplied with the tool when provided for the specific configuration.

Setup and Operation

Before Starting

1. Inspect the power cable, housing, switch, square drive, and socket for damage.
2. Choose the correct impact socket for the fastener.
3. Push the socket fully onto the 12.7 mm square drive.
4. Secure the workpiece and clear the area of people and loose materials.
5. Confirm that the direction switch is in the required position before connecting the plug.

Changing Rotation

Press the direction switch to select clockwise or counter-clockwise rotation. Change direction only when the motor and drive are completely stopped. Switching direction while the tool is running may damage the mechanism or cause loss of control.

Driving or Loosening Fasteners

1. Fit the socket squarely over the fastener.
2. Hold the tool firmly and keep the socket aligned with the bolt or nut.
3. Press the on/off switch to start the motor at maximum speed.
4. Release the switch to stop the tool.
5. Allow the drive to stop fully before moving to another fastener or placing the tool down.

Impact duration and operating speed affect the tightening result. Use the impact driver only for pre-assembly when tightening screws or nuts. Check the final reference torque with a torque wrench set to the required value.

Always follow the fastener or vehicle manufacturer’s tightening instructions and inspection schedule. After changing a vehicle wheel, check the wheel bolts or nuts with a torque wrench after driving 50 to 100 km.

Cleaning and Maintenance

Unplug the 62552 Electric Impact Driver before cleaning, inspecting, or touching its accessories. Regular care helps maintain reliable operation and reduces the risk of injury.

• Do not spray the tool with water or immerse it in liquid.
• Wipe the housing and handles with a slightly damp cloth or clean them with a brush.
• Keep the ventilation openings clear of dust and debris.
• Do not use aggressive cleaning agents or solvents, which may damage the housing.
• Inspect the moving parts, housing, cable, and accessories regularly for damage or obstruction.
• Use original replacement parts for servicing.

Replacing the Carbon Brushes

Replace carbon brushes only as a matched pair. Allow the tool to cool before beginning this work.

1. Switch off the tool and unplug it from the mains.
2. Allow the housing to cool.
3. Loosen a sealing cap with a screwdriver and remove the cap.
4. Pull the carbon brush from its holder.
5. Insert a new carbon brush into the holder.
6. Refit the sealing cap.
7. Repeat the removal and replacement procedure on the opposite side.

Storage

Store the impact driver unplugged in a dry location that is inaccessible to children. Keep the cable arranged to avoid sharp bends and protect the tool and sockets from moisture.

Troubleshooting

• The tool does not start: Check that the plug is connected to a suitable mains supply and that the on/off switch is being pressed. Inspect the cable and switch for damage. Do not use the tool if either is defective.
• The socket does not rotate in the desired direction: Release the switch, wait for the drive to stop completely, and then reposition the direction switch.
• The fastener is not tightened correctly: Confirm that the socket fits properly, keep the tool aligned, and avoid relying on impact time as a torque measurement. Verify the final torque with a torque wrench.
• The tool becomes difficult to control: Stop operation, check the socket and fastener alignment, secure the workpiece, and improve your stance before continuing.
• The tool overheats or performs poorly: Stop using it, unplug it, and check that the ventilation slots are clean and unobstructed. Allow the tool to cool before inspection.

Disposal

Do not dispose of the electric impact driver with ordinary household waste. Electrical and electronic equipment should be taken to an appropriate collection or recycling facility in accordance with local disposal requirements. Proper recycling helps recover materials and reduces environmental harm.

Pros & Cons

Pros

• High counter-clockwise torque for loosening tight fasteners.
• Standard 1/2-inch square drive for common impact sockets.
• Includes four commonly used socket sizes.
• Three-metre cable provides useful working reach.
• Fixed high-speed operation is straightforward to use.

Cons

• Mains-powered operation requires access to a suitable electrical outlet.
• The tool has no variable-speed control described in the operating instructions.
• Clockwise tightening torque is limited and must be verified with a torque wrench.
• Its 2.1 kg weight may require firm handling during extended work.