Performance Tool 3 Ton Rapid Lift Floor Jack W1616

The Performance Tool Rapid Lift Floor Jack W1616 is a heavy-duty and high-quality floor jack designed for professional use. This powerful Performance Tool 3 Ton Rapid Lift Floor Jack W1616 is capable of lifting up to 3 tons, making it perfect for garages, workshops, and auto repair shops. The estimated price of this product is around $300 to $400, and it is now available in the market.

Detailed Specifications

The 3 Ton Rapid Lift Floor Jack W1616 features a rapid pump design that can lift a load up to 16 inches in just 5 pumps. It has a built-in saddle pad that protects the vehicle's frame and a built-in safety overload system that prevents the jack from lifting beyond its capacity. The jack also has a swivel casters and rear wheels that provide easy mobility and positioning. Additionally, it has a steel lift arm and a reinforced lift pad for added durability and strength.

Capacity: 6,000 lbs.
Low Height: 4-5/8"
Max. Height: 19-3/4"
Lift Range: 15-1/8"

Description of Rapid Lift Floor Jack W1616

The Performance Tool 3 Ton Rapid Lift Floor Jack W1616 is built to last, with a heavy-duty steel construction that can withstand even the toughest working conditions. Its rapid pump design makes it easy to lift heavy loads quickly, while its built-in safety features ensure that the jack is always used safely. The jack's swivel casters and rear wheels make it easy to move and position, while its reinforced lift pad and steel lift arm provide added stability and strength. With a lifting range of 5.5 to 16 inches, this floor jack is suitable for a wide range of vehicles, including cars, trucks, and SUVs.

performance_tool_3_ton_rapid_lift_floor_jack_w1616-parts_list.png

#	Description	Qty.
1	Main Frame	1
2	Front Wheel	2
3	Washer	2
4	Retaining Ring	2
5	Caster	2
6	Lock Washer	2
6A	Hex Nut	2
7	Power Unit	1
8	Lock Washer	2
9	Cap Screw	2
10	Link Block	1
11	Cotter Pin	1
12	Return Spring	1
13	Lift Arm	1
14	Link Bolt	2
15	Lock Washer	2
16	Hex Nut	2
17	Shaft	1
18	Snap Ring	2
19	Snap Ring	2
20	Saddle	1
21	Grease Fitting	1
22	Handle Socket	1
23	Gear Shaft	1
24	Gear	1
25	Washer	1
26	Hex Nut	1
27	Washer	1
28	Cotter Pin	1
29	Lock Washer	2
30	Bolt	2
31	Torsion Spring	1
32	Pin	1
33	Lower Handle	1
34	Upper Handle	1
35	Hex Head Screw	1
36	Handle Bolt	1
37	Washer	1
38	Release Valve	1
39	Release Valve Gear	1
40	Retaining Ring	2

REPLACEMENT PARTS LIST

performance_tool_3_ton_rapid_lift_floor_jack_w1616-_parts.png

Ram Assembly Parts List

Parts List

#	Description	Qty.
1	Top Nut	1
*2	O-Ring	1
*3	O-Ring	2
4	Reservoir	1
5	Oil Fill Plug	1
6	Ram	1
*7	O-Ring	1
*8	Guide Plate	1
9	Cylinder	1
10	O-Ring	1
11	Washer	1
12	Spring	1
13	Shaft	1
14	Ram	1
15	Ball	1
16	Spring	1
17	Screw	1
*18	O-Ring	1
19	Small Cylinder	1
*20	Screw	1
*21	Ball	2
*22	Ball	3
*23	Ball	3
24	Filter Oil Tubes	2
*25	Pin	1
*26	Release Valve Shaft	1
27	Release Valve Gear	1
28	Washer	1
29	Nut	1
*30	Plug Screw	1
*31	Washer	1
*32	Overload Valve Screw	1
*33	Spring	1
*34	Spring Base	1
*35	Ball	1
36	Pump Piston	1
*37	Backup Ring	1
*38	O-Ring	1
39	Valve Block	1

(*) Denotes item included in repair kit #W1616CK

Replacement parts available

Part Number	Description
W1616CK	Ram Repair Kit
W1616-1	Front Stationary Wheel
W1616-2	Rear Caster Wheel
W1616-3	Saddle
W1616-4	Release Valve Gear Set
W1616-5	Handle Socket Bolt
W1616-6	Torsion Spring
W1616-7	Handle Assembly
W1616-8	Handle Retaining Bolt
W1616-9	Pump Piston

OPERATION

Before using your jack
Turn release valve counter-clockwise to open. Pump jack handle about 6 full strokes to assure complete distribution of hydraulic fluid.

To raise
Turn release valve clockwise to close. Make certain that load is on center of saddle. Pump the jack handle to raise load to desired height. Transfer load to jack stands or other appropriate supports before working under load.

To lower
Raise load slightly to remove jack stands. Slowly turn release valve counter-clockwise just enough to allow controlled descent. (Never turn counter-clockwise more than 3 full turns)

CARE & MAINTENANCE

When jack is not in use, lifting arm and handle sleeve should be infully down position to keep their precision machined surfaces free from corrosion.
Keep jack clean and well lubricated.
For best results, use only hydraulic fluid with a rating of SAE 10 for refills. Check fluid level with jack in fully down position. Fluid level should be 5mm below filler hole.
Regularly check for loose, worn or damaged parts and repair or replace as necessary.
Replace worn or damaged parts with Performance Tool replacement parts. Be sure that only qualified personnel perform repairs.

IMPORTANT SAFETY INFORMATION

Read these safety warnings before operation.
WARNING

Failure to heed these warnings may result in loss of load, damage to jack, and/or jack failure resulting in personal injury or property damage.
This is a lifting device only. Do not move load while it is on the jack. Load must be supported immediately by Jack Stands or other appropriate means.
Do not overload jack beyond rated capacity. Overloading can cause damage to or failure of the jack.
REFER TO YOUR VEHICLE OWNERS MANUAL FOR PROPER JACKING PROCEDURES. Lift only on areas of the vehicle as specified by the vehicle manufacturer.
This jack is designed for use only on hard level surfaces capable of sustaining the load. Use of jack on other than hard level surfaces can result in jack instability and possible loss of load.
Be sure all personnel are clear of load before lowering load.
Ensure that no personnel pass underneath load until load is securely supported by jack stands.

TROUBLESHOOTING

Your Performance Tool hydraulic jack was constructed of quality materials and workmanship and will give you many years of trouble-free use when cared for as described in the "Care & Maintenance" section on page 3. However, as with any mechanical device, periodic adjustments are necessary to maintain a peak level of performance. Should your jack be displaying any of the following symptoms, the simple procedures shown below will correct the problem.
WARNING: Remove jack from service before making adjustments

performance_tool_3_ton_rapid_lift_floor_jack_w1616-removing_the_jack.png

NOTE: Problems listed above with more than one solution may have a combination of causes. Please be sure that all solutions listed for each problem have been checked to eliminate the possibility of further trouble. Sometimes solutions may need to be repeated for best results.

Pros & Cons

Pros

Rapid pump design for quick lifting
Built-in safety overload system
Swivel casters and rear wheels for easy mobility
Reinforced lift pad and steel lift arm for added durability
Lifting range of 5.5 to 16 inches

Cons

Heavy and difficult to transport
Expensive compared to other floor jacks
Not suitable for low-profile vehicles
May require some assembly upon delivery

Customer Reviews of Performance Tool 3 Ton Rapid Lift Floor Jack W1616

Customers have praised the Rapid Lift Floor Jack W1616 for its quick lifting and easy mobility. Many have noted its durability and strength, with several users reporting that they have been using the jack for several years without any issues. However, some customers have criticized its heavy weight and high price. The most common complaint is that the jack is not suitable for low-profile vehicles, as the lifting pad may not be able to reach the lift points.

performance tool Manuals

Read More