Introduction Eufy RoboVac Cleaner 11S T2108

The eufy RoboVac Cleaner 11S T2108 is a sleek and efficient robotic vacuum designed to simplify home cleaning. With a super-slim profile of just 2.85 inches, it easily navigates under furniture while delivering strong suction power of up to 1300 Pa. Equipped with BoostIQ technology, it automatically increases suction when needed for deep cleaning. This quiet and self-charging vacuum can operate for up to 100 minutes on a single charge, priced at approximately $249.99, making it a smart choice for effortless maintenance.

About Your RoboVac 

What's in the Box 

RoboVac Anatomy

Top & Side

Bottom

Dust Collector

Suction Inlet

Charging Base

Remote Control 

1. Start Auto cleaning
2. Start Auto cleaning Stop cleaning
3. Start Spot cleaning
4. Start Edge cleaning Adjust time
5. Adjust suction power level in Auto/Single Room Cleaning mode Control cleaning direction manually
6. Adjust the hour and minute
7. Start Single Room cleaning
8. Return RoboVac to Charging Base Schedule Auto cleaning start time

Remote Control Display 

1. Returning to Charging Base
2. Auto cleaning mode selected
3. Spot cleaning mode selected
4. Edge cleaning mode selected
5. Single Room cleaning mode selected 
6. Clock
7. Standard suction power enabled 
8. BoostIQ dynamic suction power enabled 
9. Max suction power enabled
10. Scheduled cleaning time

TIP: Install 2 AAA batteries before using the remote control for the first time. Make sure the positive and negative ends are facing the correct polarity direction as marked in the battery compartment.

LED Indication

You can see the status of RoboVac from the LED indicator. 

Specifications

Using Your RoboVac 

Important Tips Before Use

1. Remove power cords and small objects from the floor that may entangle RoboVac.
2. Fold tasseled edges of area rugs underneath to prevent tangling RoboVac. Avoid cleaning very dark-colored high-pile rugs or rugs thicker than 1.02 in/26 mm as they may cause RoboVac to malfunction.
3. Keep RoboVac away from spaces lower than 2.87 in/73 mm to prevent RoboVac from getting stuck. If necessary, place a physical barrier to block off the problem areas.
4. Keep RoboVac away from wet areas.
5. RoboVac may climb on top of objects less than 0.63 in/16 mm in height. Remove these objects if possible.
6. Anti-drop sensors prevent RoboVac from tumbling down stairs and steep drops. They may work less effectively if dirty or used on reflective/very dark-colored floors. It is recommended to place physical barriers to block off areas where RoboVac may fall.

TIP: Place physical barriers in front of fireplaces and areas that may cause damage to RoboVac if entered.

Preparation

1. Install the side brushes before use.

2. Turn on the main power switch on the bottom of RoboVac.
   TIP: Remove the sticker next to the power switch, and the foam blocks beside the bumper before use.

   

3. Place the Charging Base on a hard, level surface and against a wall.

   

4. Remove objects within 3 ft/1 m of the left and right side and within 6 ft/2 m of the front of the charging base.

5. Connect the round connector of the adapter into the power socket on the Charging Base and the other end into a wall outlet.

   

   When the Charging Base connects to AC power, the LED indicator on the Charging Base is SOLID WHITE.
   TIP: Install the Charging Base in a location that RoboVac can easily access. It is recommended to place the Charging Base against a wall, and on a hard-level surface rather than on rugs or carpets.
   Always keep the Charging Base plugged in, otherwise RoboVac will not automatically return to it.

Charge Your RoboVac

• RoboVac has a pre-installed rechargeable battery that has to be fully charged before use.
• RoboVac returns to the Charging Base at the end of a cleaning cycle or when its battery is running low.

Method 1: Attach RoboVac to the Charging Base by aligning its charging pins with the charging pins on the base.  

Method 2: Press on the remote control to return RoboVac to the Charging Base. 

TIP: Turn off the main power switch if RoboVac will not be used for a long period of time. To preserve the battery’s lifespan, recharge at least once every 6 months. 

Start / Stop Cleaning 

NOTE: Make sure the main power switch on the bottom of RoboVac is turned on before use.

1. Presson RoboVac or on the remote control to start cleaning in Auto Mode.
2. Press on RoboVac or on the remote control to stop cleaning.

Select a Cleaning Mode

Auto cleaning 

RoboVac optimizes its cleaning path by selecting different cleaning modes automatically until cleaning is complete. This is the most commonly used cleaning mode.
Press on RoboVac or on the remote control to start cleaning in Auto Mode. 

TIP

• RoboVac will return to the Charging Base automatically when the battery level becomes low or when RoboVac finishes cleaning.
• By default, RoboVac starts in Auto cleaning mode when it is turned on.

BoostIQ Feature 

When the BoostIQ feature is enabled, RoboVac will automatically increase the suction power if it detects stronger power is needed to ensure the best clean. BoostIQ™ is ideal for cleaning thicker carpets and hard-to-sweep messes, which will reduce the total cleaning time, but increase the noise level. If the vacuuming noise caused by BoostIQ™ disturbs you, you can disable this feature. This feature only works in Auto and Single Room cleaning modes.
In Auto or Single Room cleaning mode, press on the remote control repeatedly to adjust the suction power level. 

The corresponding icon is displayed on the remote control.

TIP: When RoboVac starts cleaning in Auto or Single Room mode the next time, it will clean according to the suction power level you previously selected.

Spot cleaning 

RoboVac intensively cleans a specific area in a spiral pattern, useful if there is a concentrated area of dust or debris. In Spot mode, RoboVac will stop cleaning after 2 minutes. 
Press on the remote control to start cleaning in Spot mode.

Edge cleaning

RoboVac reduces its speed when it detects a wall and then follows the wall to ensure the edge is cleaned thoroughly. In Edge mode, RoboVac will clean for 20 minutes and return to the Charging Base.
Press on the remote control to start cleaning in Edge mode.

Single Room cleaning

RoboVac intensively cleans one single room and stops after 30 minutes. Select this mode only when one specific room needs to be cleaned. Make sure to confine RoboVac to the room by closing the door. 
Press  on the remote control to start cleaning in Single Room Mode. 

Manual cleaning 

You can direct RoboVac to clean a particular area by using the directional buttons on the remote control.

Description

The eufy RoboVac Cleaner 11S T2108 measures 2.85 inches in height, making it one of the slimmest robotic vacuums on the market. It weighs approximately 5.5 pounds and has a diameter of 12.8 inches. The device is equipped with infrared sensors to avoid collisions and falls, ensuring smooth navigation around your home. It also features a HEPA-style filter, which captures allergens and other small particles, improving indoor air quality. The vacuum comes with charging dock, cleaning tool, extra set of high-performance filters, and four side brushes.

Set Time and Scheduled Cleaning

Set Time

1. Make sure the time is set correctly to your local time before setting a scheduled cleaning.
2. Make sure the main power switch on the bottom of RoboVac is turned on. 
3. Press on the remote control. The time will blink on the display. 
4. Press to set the “hour” and “minute”.
   Note: Make sure AM/PM is set correctly. 
5. Press or to save the setting. RoboVac will BEEP ONCE to indicate the time has been set.

TIP: To ensure the time is set successfully, make sure RoboVac is turned on. You will hear a beep when the time has been set.

Set a Scheduled Cleaning

You can schedule RoboVac to start cleaning at a specified time. To cancel a previously scheduled cleaning, press and hold for 3 seconds until RoboVac beeps twice and disappears.

Note: Before setting a scheduled cleaning, make sure the time has been set correctly to your local time; refer to the previous section “Set Time” for how to set the time. 

1. Make sure the main power switch on the bottom of RoboVac is turned on. 
2. Press on the remote control. will blink on the display.
3. Press to set the “hour” and “minute”.
   Note: Make sure AM/PM is set correctly. 
4. Press or to save the setting. RoboVac will BEEP ONCE to indicate the schedule has been set.

TIP: To ensure the schedule is set successfully, make sure RoboVac is turned on. You will hear a beep when the schedule has been set.

Setup Guide

To set up the eufy RoboVac Cleaner 11S T2108, 

1. Start by charging the device for at least 4 hours before initial use. Once charged, place the robot on a flat surface and press the single-button interface to turn it on. 
2. The vacuum will begin its cleaning cycle automatically. For optimal performance, ensure the area is clear of clutter and wires. 
3. The robot will navigate and clean your space using its infrared sensors. 
4. After the cleaning cycle is complete, the vacuum will return to its charging dock to recharge.
5. No Wi-Fi or Bluetooth setup is required, making it straightforward and user-friendly.

Cleaning and Maintenance 

For optimal performance, follow the instructions below to clean and maintain RoboVac regularly. The cleaning/replacement frequency will depend on your usage habits of RoboVac. 

Recommended cleaning/replacement frequency:

Clean the Dust Collector and Filters

1. Press the dust collector release button to pull the dust collector out. 
2. Open and empty the dust collector. 
3. Remove the pre-filter by pulling the hooks as shown.
4. Take out the foam filter and high-performance filter.
5. Clean the dust collector and filters with a vacuum cleaner or a cleaning brush. 

6. Put the filters and pre-filter back together in the dust collector.

   

7. Push the dust collector back into the main unit.

   

TIP: You can wash the dust collector, pre-filter and foam filter with water. Be sure to air-dry them thoroughly before reassembling. Do not wash the high-performance filter with water, as it may damage the filter and reduce the suction power.

Clean the Rolling Brush

1. Pull on the release tabs to unlock the brush guard as shown. 
2. Lift the rolling brush to remove.  
3. Clean the rolling brush with the provided cleaning tool or a vacuum cleaner. 
4. Reinstall the rolling brush by inserting the fixed protruding end first and then clicking into place.
5. Press down to snap the brush guard into place. 

Clean the Side Brushes

Foreign substances, such as hair, can easily get tangled in the side brushes, and dirt may adhere to them. Be sure to clean them regularly. 

1. Remove the side brushes. 
2. Carefully unwind and pull off any hair or string that is wrapped between the main unit and the side brushes. 
3. Use a cloth dampened with warm water to remove dust from the brushes or to gently reshape them. 

TIP: Only use the side brushes when they are completely dry.

Replace the Side Brushes 

The side brushes may become bent or damaged after being used for a period of time. Follow the instructions below to replace them. 
Pull off the old side brushes and snap the new ones into place. 

Clean the Sensors and Charging Pins

To maintain the best performance, clean the drop sensors and charging pins regularly. 

• Dust off the drop sensors and charging contact pins using a cloth or cleaning brush.

Clean the Swivel Wheel

Hair or dust particles can easily get entangled in the swivel wheel. Be sure to clean the swivel wheel periodically and as needed. 

1. Clean the Swivel Wheel
2. Clean any hair or debris wrapped around the wheel or entangled inside the wheel cavity. 
3. Reinstall the wheel and push in until it clicks into place.

TIP

• You can clean the swivel wheel with water. 
• Use the swivel wheel only when it is completely dry.

Important Safety Instructions

To reduce the risk of injury or damage, read these safety instructions carefully and keep them at hand when setting up, using, and maintaining this device.

WARNING SYMBOLS USED
This is the safety alert symbol. This symbol alerts you to potential hazards that could result in property damage and/or serious bodily harm or death.

• This device can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of this device in a safe way and understand the hazards involved.
• Children should be supervised to ensure they do not play with this device.
• Cleaning and maintenance shall not be performed by children without adult supervision.
• This device is only to be used with the power supply unit provided.
• For the purposes of recharging the battery, only use the detachable power supply unit provided with this device.
• The battery must be removed from this device before this device is disposed of. To remove the battery from this device, first remove the screws on the bottom, then remove the main PCB and unscrew the battery cover using a screwdriver. Remove the battery by disconnecting the quick connector.
• The used battery should be placed in a sealed plastic bag and disposed of safely according to local environmental regulations.
• The external flexible cable or cord of the power supply unit cannot be replaced; if the cord is damaged, the power supply unit shall be disposed of.
• This device is for indoor use only.
• This device is not a toy. Do not sit or stand on this device. Small children and pets should be supervised when this device is operating.
• Store and operate this device in room temperature environments only.
• Clean with a cloth dampened with water only.
• Do not use this device to pick up anything that is burning or smoking.
• Do not use this device to pick up spills of bleach, paint, chemicals, or anything wet.
• Before using this device, pick up objects like clothing and loose paper. Lift up cords for blinds or curtains, and move power cords and fragile objects out of the way. If this device passes over a power cord and drags it, an object could be pulled off a table or shelf.
• If the room to be cleaned has a balcony, a physical barrier should be used to prevent access to the balcony and to ensure safe operation.
• Do not place anything on top of this device.
• Be aware that this device moves around on its own. Take care when walking in the area where this device is operating to avoid stepping on it.
• Do not operate this device in areas with exposed electrical outlets on the floor.
• Do not expose the electronics of this device, its battery, or the integrated Charging Base. There are no user-serviceable parts inside.
• Do not use this device on an unfinished, unsealed, waxed or rough floor. It may result in damage to the floor and this device. Use only on hard floor surfaces or low-pile carpet.
• This device has been designed to be used on floors without scratching them. We still recommend that you test this device on a small area of the room to be cleaned to ensure no scratches are made before cleaning the whole room.

Troubleshooting 

Error Tones 

When RoboVac is in trouble, it will emit a series of short or long beeps and the red indicator on RoboVac will be solid or flashing. 

Flashing red indicator light

Solid red indicator light

Pros & Cons

Pros

• Slim Design: Fits under most furniture for thorough cleaning.
• Quiet Operation: Operates at a noise level of around 55 decibels.
• Powerful Suction: Captures dust, dirt, and allergens effectively.
• Easy Maintenance: Simple to clean and maintain brushes and filters.
• Affordable: Priced competitively compared to other robotic vacuums.

Cons

• No Wi-Fi Connectivity: Cannot be controlled remotely via app.
• No Voice Assistant Integration: Not compatible with Alexa or Google Assistant.
• Short Battery Life: Approximately 1 hour and 30 minutes before needing a recharge.
• No Virtual Barrier Support: No option for creating virtual barriers to restrict areas.

Customer Reviews

Customers have praised the eufy RoboVac Cleaner 11S T2108 for its quiet operation, powerful suction, and ease of use. Many users appreciate its slim design, which allows it to reach areas other vacuums cannot. However, some users have noted that the battery life could be longer and that the lack of Wi-Fi connectivity limits its functionality compared to more advanced models.

Common complaints include issues with navigation around complex spaces and occasional difficulty in finding the charging dock. Despite these minor drawbacks, the eufy RoboVac Cleaner 11S T2108 remains a popular choice for those seeking a reliable and efficient robotic vacuum.