Ifb Appliances Senorita Aqua SX Machine 1000RPM User Manual

cover-image

Content

Introduction

The IFB Senorita Aqua SX Machine 1000RPM is a fully automatic front-load washing machine designed to provide efficient laundry solutions for modern households. With a capacity of 6.5 kg, it is suitable for small to medium-sized families and features 100 wash programs tailored for various fabric types. The machine's 1000 RPM spin speed ensures effective drying, while the Aqua Energie technology helps treat hard water for better washing results. Priced at approximately $350, it offers a perfect blend of performance and convenience.

Specifications

  • Model: Senorita Aqua SX 6.5KG 1000RPM
  • Power supply: 220-240 V Single Phase 50 Hz
  • Dimension: 50.6cm (D) x 59.8cm (W) x 87.5cm (H)
  • Net weight: 66 Kg
  • Capacity: 6.5 Kg of dry cotton
  • Wash care programs: 15 (>100 with options)
  • Selector buttons: Delay Start, Spin, Pre Wash, Extra Rinse, Rinse Hold, Soak, Start/Pause
  • Selector knob: Program selector
  • Spin speed: 400-1000 RPM or Spin Cancel
  • Program duration: 151 minutes maximum
  • 15 minutes minimum
  • Water consumption*: 43 Litres
  • Water pressure: 0.3 Bar-10 Bar (30 KPa-1000 KPa)
  • Power consumption max: 2200 W
  • Drain pump rating: 30 W
  • Heater rating: 2000 W
  • Drum: Stainless steel

Product Overview

product_overview.png

Control Panel

control_panel_ifb_senorita_aqua_sx_machine_1000rpm.png

Safety guidelines for installation

safety_guidelines_for_installation.png
  • Keep the packaging material. It may come in handy when shifting residence.
    • Old hoses must not be reused. Always use the new hoses delivered with the machine. Before cleaning the machine, ensure that you disconnect the main electricity supply and take the plug out of the socket.
    • Not removing all the packaging and transit bolts before using the appliance may lead to serious damage. Please do not operate the machine until the transit bolts have been removed.
  • All washing machine installation work must be carried out only by authorised IFB Service Personnel.
  • Pre-installation work such as plumbing and electrical connections must be carried out by a qualified fitter, electrician or technician.
  • Do not operate the appliance where inflammable substances such as oil, benzene or highly inflammable gas are present. Such materials may cause fire or explosion. Never use combustible detergents.
  • Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point O and above SO C.
  • Install the machine in a room with adequate ventilation. Avoid a room with no windows. The back of the machine should be at least 4 inches (1 00 mm) away from the wall.
  • The machine is provided with ventilating openings on the base. Always put the machine on the floor after removing the carpet.
  • Do not install the machine in a damp area or bathroom with exposure to a direct shower.
  • Protect the machine from direct sunlight and rainfall.
  • Do not place the machine on a slanting, uneven or unstable surface.
  • A concrete floor is the most suitable installation surface for a washing machine, being far less prone to vibration during the spin cycle than wooden floorboards.
    The washing machine is not suitable for connection to a hot water supply.
    The machine is designed to operate with water flow pressure between 0.3 Bar-10 Bar. Lower water pressure can lead to machine malfunction.

Read all instructions and explanations for installation carefully before use. Follow the instructions carefully. Keep the operating instructions handy for later use.

Safety Information

Any damage, which may be caused by cockroaches or other vermin, will not be covered by the appliance guarantee.

  • Do not install and use a damaged machine. Before connecting the machine, ensure that the connection data on the data plate (fusing, voltage and frequency) match the main electricity supply. If in any doubt, consult IFB Care.
  • Do not wash or dry articles that have been cleaned, washed, soaked in or dabbed with combustible or explosive substances (such as oil, paint, gasoline, degreasers, dry cleaning solvents, kerosene etc). This may result in fire or explosions.
  • Before using the machine for the first time, check that the transit bolt at the rear of the machine has been removed (refer topic Safety Guidelines for installation).
  • Turn OFF the stopcock if the machine is to be left for any length of time (eg holidays) especially if there is no floor drain (gully) in the immediate vicinity.
  • This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instructions concerning the use of the appliance in a safe way and understand the hazards involved.
  • Children should not play with the appliance.
  • Cleaning and user maintenance should not be performed by children without supervision.

Caution 

  • The electrical safety of this appliance can only be guaranteed when continuity is complete between the machine and an effective earthing system, which complies with local and national regulations. It is most important that a qualified electrician regularly tests this basic safety requirement. The manufacturer cannot be held responsible for the consequences of an inadequate earthing system.
  • For safety reasons do not operate this appliance on an extension cable. Extension leads do not guarantee the required safety of the appliance. There is danger of overheating.
    The machine is built in accordance with current safety requirements.
    Unauthorised repairs could result in unforeseen dangers for the user, for which the manufacturer cannot accept responsibility. Only authorised IFB personnel should undertake repairs.
  • The machine is only completely isolated from the electricity supply when it is switched OFF at the wall socket and the plug is taken out, or it is switched OFF from the main source, or the main fuse is taken out or the MCB switched OFF. This machine must only be connected to the onsite water supply using a new hose kit. Old hoses must not be reused. Only genuine IFB original spare parts must replace faulty components. Only when these parts are fitted can the safety standards of the machine be guaranteed.
    If the connection cable is faulty it must be replaced only by an IFB approved service technician to protect the user from danger.
  • A washer and dryer should never be stacked without using the proper stacking kit. Doing so is extremely dangerous, as the dryer may vibrate off the washing machine during use.

Warnings

  • Do not pull the cord to disconnect the plug. Hold the plug itself. Do not insert or remove the plug with damp hands.
  • Do not drag or move the washing machine if it contains the wash load or when in operation.
  • Do not spill water over the machine. In case of spillage, wipe dry. Avoid the machine coming in contact with floor cleaning chemicals.
  • Do not wash or spray water over the switch or control panel.
  • Do not wash shoes or utensils in the machine.
  • Use detergent recommended for washing machines.
  • Keep your machine dry to avoid corrosion/rusting. Take special care to wipe the machine after cleaning coin trap.
  • Check label on garments for determining conditions under which fabrics are to be washed.
  • The machine is tested with water during assembly for performance checking. Condensed droplets of water may remain inside the drum. It is advisable to run the machine without a wash load in Cotton maximum temperature program with detergent for the first time after installation. Ensure that the machine is connected to a 3 pin socket with good earthing and 1 6 Amp MCB or other automatic short circuit protection devices.
  • Textiles that have been pre-treated in solvent-based cleaning agents must be thoroughly rinsed in clean water before being washed in the machine.
  • Never use solvent-based cleaning agents in this machine, as this may result in damage to component parts and create toxic fumes. Such detergents also pose a threat of fire and explosion hazards.
  • Only use dyes specified by the manufacturer as suitable for use in a domestic washing machine. Always read the manufacturer's instructions carefully.
  • Colour run and dye removers contain sulphur compounds, which can cause damage such as corrosion. Do not use such products in this machine.
  • For machines with a porthole door, remember that the porthole glass will be hot when washing at very high temperatures. Do not let children touch it.
  • Always make sure that the drum is stationary before removing clothes. Reaching into a moving drum is extremely dangerous.

Flooding danger 

  • While hooking the drain hose into a wash basin, check that the water drains OFF quickly to prevent the sink from overflowing. Make sure the drain hose is secure so that the force of the water flowing out of the hose does not dislodge it. Otherwise this will result in flooding.
  • Take care to ensure that foreign objects (eg nails, pins, coins, paper clips etc) do not find their way into the machine with the washing. These may damage components of the machine (eg suds container, drum etc), which in turn can result in damage to the washing.

Description

The IFB Senorita Aqua SX 1000RPM offers a blend of advanced technology and user-friendly design. Its stainless steel drum is durable and resistant to rust, ensuring long-lasting performance. The machine features an attractive and ergonomic interface that makes selecting wash programs easy. Additionally, it includes a child lock feature for safety and an auto-dry function that helps in reducing moisture after the wash cycle. The machine's anti-vibration system ensures smooth operation even at high speeds.

Getting Started With Your Machine

Installing your machine & safety guidelines

Select the right spot

  • Unpack and place the new washing machine in proximity to both water and electrical connections. Ensure that the floor is properly levelled.

    installing_your_machine_&_safety_guidelines_ifb_appliances_eva_aqua_sx_6kg_800rpm.png

Removing the transit bolts

  • Use a spanner to remove the transit bolts.
  • Insert plastic caps provided.
  • Keep the transit bolts carefully as they will be required in case you need to shift the machine again.
  • Please do not operate the machine until the transit bolts have been removed.

Leveling

levelling_ifb_senorita_aqua_sx_machine_1000rpm.png
  • Level the machine by using the adjustable screws provided at the bottom for levelling.
  • Make sure that the machine rests on all four feet on a level surface.

    leveling_of_ifb_appliances_eva_aqua_sx_6kg_800rpm.png

Connection to the water supply

  • The water inlet of the machine has a collar with parallel internal threads.

    power_supply_ifb_appliances_eva_aqua_sx_6kg_800rpm.png
  • The water supply point with an external thread/parallel thread should be available within 1 metre of the machine location.
  • Do not stretch the water supply hose.

    connection_to_the_water_supply_ifb_appliances_eva_aqua_sx_6kg_800rpm.png

Connection to the drain hose

connection_to_the_drain_hose_ifb_appliances_eva_aqua_sx_6kg_800rpm.png
  • The machine drains via a drain pump.
  • Direct the end of drain hose into a sink or a basin.
  • The drain hose should not be placed higher than 1 00 cm and not lower than 60 cm above the floor.

    connection_to_the_drain_hose_ifb_senorita_aqua_sx_machine_1000rpm.png

Electrical connection

  • It is mandatory to have a 16 Amp, 3 pin 220-240 V AC, 50 Hz electrical point with a 16 Amp MCB or automatic short circuit protection device within 1 metre of the machine.
  • Make sure your home has proper earthing and there is a firm connection between the plug and the socket. IFB recommends a separate MCB on the socket of the washing machine.
  • Proper earthing of the power socket is critical to reliable performance.
electrical_connection_ifb_appliances_eva_aqua_sx_6kg_800rpm.png

Get More From IFB Senorita Aqua SX 1000RPM

Tips for best results 

Before washing

  • Empty all pockets.
  • Remove metals parts.
  • Close any zips and fasten hooks etc before washing.
  • Do not wash anything in the machine that is specified as non-machine washable on the wash care label.

While sorting

  • Separate polyester fabrics from cotton fabrics.
  • Try to have a mix of large and small clothes in each wash load.
  • Dark clothes should be washed separately and not with whites.

While loading

  • Load large items first, preferably half the total wash load.
  • Do not wash single items-add one or two similar items.
  • Place small items such as infants' socks, nylon stockings, handkerchiefs etc in a laundry bag, pillow case or something similar, as they may get caught around the door. This will also save your laundry from getting lost.

Water softening

  • Use water softening agents or adjust detergent dosage as recommended by the detergent manufacturer in case of hard water.

Easy tips to remove stains 

  • Ensure you use warm water for soaking or pre washing stained laundry.
  • Fresh stains are easier to remove.
  • Knowing what kind of stain it is, how old it is, what kind of fabric it is, and whether the fabric is color fast (check the care label) always helps treat a stain better.
  • Always start with cold or warm water as hot water can set in stains. Washing and drying can sometimes set in stains.
  • When bleach is recommended, always use a fabric-safe one. Put the stained area face down on a paper towel or white cloth. Apply the stain remover to the back of the stain. This forces the stain off the fabric instead of through it.
StainTreatment
Chewing Gum, Adhesive Tape, Rubber, CementUse ice in a plastic bag to harden the gum. Scrape off what you can and then sponge with white spirits.
BloodRinse immediately in COLD water. If stain remains, soak in COLD water with an enzyme pre-wash.
Chocolate, CocoaSponge with COLD water and soak in an enzyme pre-wash. If stain persists, rub a little detergent and rinse in COLD water.
CoffeeBlot up quickly and rinse out in COLD water. Rub in a little detergent and wash in the maximum temperature allowed for the fabric type.
Cream, Milk, Ice CreamRinse in COLD water and wash normally. If stain is still apparent, sponge with white spirits.
DeodorantRub affected areas with white vinegar and then rinse out in COLD water. Sponge with white spirits. Treat stiffened areas with an enzyme pre-wash.
Fabric SoftenerSoak in a COLD enzyme pre-wash, rinse and wash normally.
FruitTreat as soon as possible by sponging with COLD water. Rub affected areas with bar soap and wash normally.
GrassSponge with white spirits, rub in an enzyme pre-wash and wash normally.
Grease, OilLay the affected area face down on an absorbent cloth and work from the back. Sponge with white spirits or dry cleaning fluid. Wash normally.
Iron, RustApply lemon juice and salt and place in the sun or dry cleaning fluid. Wash normally.
Collars, Cuffs, CosmeticsPre-treat with pre-wash stain remover or rub with bar soap. Wash in WARM water and detergent. Moisten area with lemon juice, dry in the sun and wash normally. If stain persists and fabric allows, use a bleach.
MudBrush off dry mud and rinse in COLD water. If stain persists, rub in a little detergent and wash normally.
Paint - Oil-BasedScrape off any fresh paint and sponge with a non-flammable dry cleaning fluid and wash normally.
Paint - Water-BasedTreat while still wet. Rinse in WARM water and wash normally.
Scorch MarksDampen a cloth with hydrogen peroxide, lay it over the affected area and press with a fairly HOT iron.
InkSome inks may be impossible to remove and washing may even set it in. Use pre-wash stain remover, denatured alcohol or non-flammable dry cleaning fluid.
Nail PolishMay be impossible to remove in some cases. Place stain face down on paper towels. Apply nail polish remover to the back of the stain. Repeat, placing paper towels frequently. Do not use acetate fabrics.
Shoe Polish (Liquid)Pre-treat with a paste of granular detergent and water.
Shoe Polish (Paste)Scrape residue from fabric. Pre-treat with pre-wash stain remover or non-flammable dry cleaning fluid. Apply detergent into dampened area and wash using fabric-safe bleach.
Candle Wax, CrayonScrape off surface wax. Place stain face down between paper towels. Press with a WARM iron until wax is absorbed. Replace paper towels frequently. Treat remaining stain with pre-wash stain remover or non-flammable dry cleaning fluid. Hand wash to remove solvent and wash using fabric-safe bleach.

Setup Guide

To set up your IFB Senorita Aqua SX 1000RPM washing machine, follow these steps:

  1. Placement: Place the washing machine on a level surface away from direct sunlight.
  2. Installation: Connect the machine to a suitable power outlet and ensure proper drainage.
  3. Initial Wash Cycle: Run an empty cycle with detergent before first use to remove any manufacturing residue.
  4. Configuration: Select your preferred wash program using the intuitive control panel.

Maintenance and cleaning of your washing machine

Cleaning the detergent dispenser drawer

  • Remove detergent residues regularly.
  • Pull out the detergent dispenser drawer.
  • Clean the detergent dispenser drawer with WARM water.
  • Clean the siphon. Remove the siphon from the compartment and wash it under running WARM water.
  • Detergent residues can build up in the water jets on top of the detergent dispenser drawer housing.
  • Before fixing the detergent dispenser drawer use a bottle brush to clean them out.

    cleaning_the_detergent_dispenser_drawer.png

Cleaning the water hose mesh filter 

  • Turn OFF taps. Disconnect power supply to the machine. Unscrew the inlet hose from machine and the tap.

    cleaning_the_water_hose_mesh_filter_ifb_appliances_eva_aqua_sx_6kg_800rpm.png
  • Drain water from the hose.
  • Remove the filter mesh from the tap end of the inlet hose and clean under running water with a brush.
  • Pull the sieve out of the magnetic valve with a pair of flat nosed pliers. Clean the sieve under running water with a brush. Then fit the sieve back into the valve.
  • Screw inlet hose back to the machine and the tap. Ensure that the sieve and filter are in place. Turn ON water tap to check if the connection is watertight.

    cleaning_the_water_hose_mesh_filter_of_ifb_appliances_eva_aqua_sx_6kg_800rpm.png

Cleaning the filter 

  • Filter should be cleaned frequently in order to increase the life of the drain pump.
  • Open the detachable bottom door by using a coin or key.
  • Place a shallow container near the bottom door. Pull out the drain hose and open the drain plug to drain out the water from the machine in the container.
  • After draining the water through the drain plug, open the filter by rotating it anti-clockwise and remove foreign objects like coins, pins or hooks, if any.
  • Tighten the filter and drain plug to their original positions and close the bottom door.
  • Do not open the filter during a program run.

    cleaning_the_filter_ifb_appliances_eva_aqua_sx_6kg_800rpm.png

Use of descalant 

  • Use descalant periodically to increase the life of the heater and to remove scaling on the heater and drum due to hard water.
  • Follow the instructions of the descalant manufacturer and make sure that there is no laundry in the washing machine while using it.
  • Only use proprietary non-corrosive descaling agents.

    cleaning_the_filter_of_ifb_appliances_eva_aqua_sx_6kg_800rpm.png

Tub Clean Program

Run this program to eliminate any impurities, scaling, bacteria and unpleasant smell from the washing machine. Before running the Tub Clean program, empty the washing machine drum; there shouldn't be any clothes in the washing machine during Tub Clean program. Adding a small amount of powder detergent or descalant (refer topic Use of descalant) will additionally improve the effect of the Tub Clean program.

Important Do not put laundry in the washing machine during 'Tub Clean'

To run the Tub Clean Program

  • Switch ON the washing machine.
  • Put powder detergent or descalant in 'II' detergent dispenser drawer.

    to_run_the_tub_clean_program_ifb_senorita_aqua_sx_machine_1000rpm.png
  • With no laundry in drum, rotate program selector to Spin Dry/Tub Clean position.
  • Keep Extra Rinse and Rinse Hold button pressed for 3 seconds. Display will indicatedisplay_will_indicate.png and Start/Pause LED will flash. Press Start/Pause button to Start Tub Clean program. Program time remaining and capture.png display will toggle during program progress.
  • 'End' will be displayed when program finishes. If you do not use washing programs with temperatures over 60°C regularly, it is recommended to run the Tub Clean program at least once per month.

    to_run_the_tub_clean_program_of.png

Cloth weights

cloth_weights.png

Sheets

  • Cotton (double): 1 Kg
  • Cotton (single): 500 g
  • Non-cotton (double): 650 g
  • Non-cotton (single): 400 g

Pillow Slips

  • Cotton pillow slips: 110 g
  • Other pillow slips: 85 g

Table Cloth

  • Small: 230 g
  • Large: 600 g
  • Table napkins (4): 150 g

Bedspread

  • Bedspread: 3 Kg

Blankets

  • Wool: 2 Kg
  • Acrylic: 1.5 Kg

Bottoms

  • Lungi/Dhoti
  • Skirts
  • Trousers
  • Jeans

Tops

  • Cotton shirts
  • Other shirts
  • Cotton blouses
  • Other blouses
  • Woollen sweaters
  • Heavy sweaters
  • Light sweaters
  • Other clothes

Sarees

  • Cotton saree: 400 g
  • Synthetic saree: 300 g

Towels

  • Bath towels: 600 g
  • Hand towels: 250 g

Other Clothing

  • Pyjama kurta: 400 g
  • Panties: 60 g
  • Cotton vests: 100 g
  • Underslips: 100 g
  • Long socks, 2 pairs: 150 g
  • Short socks, 2 pairs: 85 g
  • 6 handkerchiefs: 85 g
  • 12 napkins: 1.1 Kg

Troubleshooting

SYMPTOM: Digital Display does not glow.

Probable CauseSolution
Power supply is not turned ONEnsure that the supply mains switch is ON.
Electrical power cord may not be plugged in or connection may be looseMake sure that the plug is plugged in and check for loose connection in plug/socket.
Program Selector in OFF positionEnsure that the Program is selected.

SYMPTOM: Washing machine door does not open.

Probable CauseSolution
Machine is in operationCheck if the program is active. If Yes, pause the program and check the door LED indication. For safety reasons, the washing machine door cannot be opened when the water level, temperature or speed is too high.
Door LED is OFFCheck if door LED is OFF. Door will open only when door LED is ON.
Child Lock is activeDeactivate the Child Lock and wait for 1-2 minutes till door LED glows.

SYMPTOM: Program does not start.

Probable CauseSolution
Machine Start/Pause button not pressedEnsure that the Start/Pause button is switched ON. The symbol will blink when it is pressed and Start/Pause LED will glow.
Water supply tap not turned ON/ no water supply/low water pressureOpen the tap fully and ensure that there is water supply with normal water pressure.
Door not closed properlyOpen and close the door firmly.
Program either in Pause/Soak or Rinse Hold modeCheck Digital Display or LED status and refer to the user manual.

SYMPTOM: Water does not enter into machine. Detergent not being flushed into the drum.

Probable CauseSolution
Water supply tap not turned ON/ no water supply/low water pressureOpen the tap fully and ensure that there is water supply with normal water pressure.
Door not closed properlyOpen and close the door firmly.
Bent inlet hose, sieve or inlet valve/inlet hose cloggedCheck if the inlet hose is bent or sieve is blocked.

SYMPTOM: Suds escaping from detergent dispenser tray. Excessive foam in drum. Residues of detergent on clothes.

Probable CauseSolution
Detergent used is not a Front Loading detergentUse detergent recommended for Front Loading washing machines only.
Excessive detergent usedReduce the detergent dosage.
Overloading of clothesDo not overload the wash.
Cold wash programUse hot wash program.
Low water pressureStart when water pressure is normal.

SYMPTOM: Water leakage from machine.

Probable CauseSolution
Inlet hose connection looseCheck and tighten the inlet hose connection.
Filter not tightenedCheck and tighten the filter.
Inlet hose leakingContact IFB Care.

SYMPTOM: Machine does not drain.

Probable CauseSolution
Filter cloggedCheck and clean the filter.
Drain hose kinked or cloggedClean and straighten the drain hose.
Drain hose above 1 metre from the floor levelDrain hose should be placed between 1 metre and 100 cm from the ground level.

SYMPTOM: Machine does not spin or clothes stay wet.

Probable CauseSolution
Load is too small, Unbalanced loadAdd 1 or 2 similar items to help balance the load. Rearrange load to allow proper spinning.
Overloading of clothesLoad clothes as per the fabric type and capacity recommended for the chosen program.
Spin speed is set to 0 RPM or lower Spin Speed is selectedSelect higher Spin Speed.
Rinse Hold option selectedAt Rinse Hold stage, press "Start/Pause" button.
Filter cloggedCheck and clean filter.
Excessive/high foaming detergent

Use detergent recommended for Front Loading washing machines only.

 

SYMPTOM: Machine vibrates more during spinning.

Probable CauseSolution
Machine not leveled properlyCheck and level the machine.
Filter clogged partiallyCheck and clean the filter.
Unbalanced loadAdd 1 or 2 similar items to help balance the load. Rearrange load to allow proper spinning.

SYMPTOM: Motor noise.

  • It is normal for noises to be heard while the motor is running.

SYMPTOM: Pump noise.

  • It is normal for noises to be heard from the pump during the start-up and final stage of draining. However, check for filter clogging.   

SYMPTOM: Program cycle time delayed.

  • It is normal as the washing machine time may vary depending upon the type and quantity of laundry, inlet water pressure, inlet water temperature, variations in power supply and other usage conditions.
  • If the load is unbalanced, the machine may make several attempts to redistribute the clothes in order to minimize the vibrations resulting in extended program duration.   

SYMPTOM: Poor soil removal.

Probable CauseSolution
Incorrect detergent dosageUse correct amount of detergent for load size and water hardness.
Use of cold wash programUse hot wash program.
Load size not as per capacityUse correct load size.
Stains on clothesPre-treat stain and any soil according to directions given under 'Easy tips to remove stains'.
Mix of heavily soiled items with lightly soiled itemsSeparate heavily soiled items from lightly soiled ones.

SYMPTOM: Blue stains on clothes.

Probable CauseSolution
Excessive fabric additivesDo not overfill fabric softener and do not pour liquid fabric softener directly onto fabric.
Cheaper quality additivesUse good quality detergents and fabric softeners.

SYMPTOM: Black or grey marks on clothes.

Probable CauseSolution
Less quantity detergent/hard waterUse correct amount of detergent for load size, amount of soil and water hardness.
Some clothes already with existing stainsDo not mix good clothes with stained clothes.

SYMPTOM: Yellow or brown rust stains.

Probable CauseSolution
Dirty incoming waterBefore washing, run water for a few minutes to clean lines or start the program only when the water is clean.
Dirty washing machineTo restore the discolored load of whites use a rust remover safe for fabric.

SYMPTOM: Residue of detergent.

Probable CauseSolution
Overloading of clothesDo not overload the washer.
Excessive use of detergentUse correct amount of detergent.
Cold wash programUse hot wash program.

Pros & Cons

Pros

  • Powerful Motor: Efficient washing and drying with its 1000 RPM motor.
  • Multiple Wash Programs: Versatile options for different types of laundry.
  • Energy Efficiency: Cost-effective operation with its A+ energy rating.
  • Durable Construction: Long-lasting stainless steel drum.

Cons

  • Noisy During Spin Cycle: Some users may find it noisy during high-speed spin cycles despite noise reduction features.
  • Higher Maintenance Costs: Replacement parts can be expensive compared to other models.

Customer Reviews

Customers have generally praised the IFB Senorita Aqua SX 1000RPM for its performance and features. Many have noted its ability to handle heavy loads efficiently and its quiet operation compared to other machines in the same category. However, some users have mentioned that it can be noisy during high-speed spin cycles and that maintenance costs can be higher than expected.

Common complaints include occasional issues with drainage and minor vibrations during use. However, these issues are generally resolved through proper installation and balancing of loads.

Warranty

IFB Industries Ltd (the Company) warrants to the original domestic purchaser of this washing machine (Appliance) that it is free from defects in workmanship and materials. During 48 months from the date of purchase of the new washing machine all the parts of the washing machine which prove to be defective in workmanship and/or materials shall be replaced or repaired free of charge on intimation to the Company/Company's authorised service centre nearest to the place where the appliance is installed. This warranty is subject to limitations of warranty. 

PDF

Faqs

What is the capacity of the IFB washing machine?

The capacity of the IFB Appliances Senorita Aqua SX Machine 1000RPM washing machine is 6.5 kg.

How many wash programs does this IFB Senorita Aqua SX Machine 1000RPM offer?

Aqua SX offers multiple wash programs including Delicate, Normal, and Heavy Duty.

Is this 1000RPM energy efficient?

IFB Senorita Aqua SX Machine has an A+ energy rating for cost-effective operation.

What material is used for the drum in this washing machine?

The drum is made of stainless steel which is durable and resistant to rust.

How do I troubleshoot if my IFB Senorita Aqua does not turn on?

Check if the machine is properly plugged in and if there are any power outages. Also ensure that the child lock feature has not been activated inadvertently.

Can I run an empty cycle with detergent before first use?

Running an empty cycle with detergent before first use helps remove any manufacturing residue from the machine.

What should I do if my IFB Appliances Senorita Aqua SX Machine 1000RPM starts leaking water?

Check for any blockages in the drain hose or ensure that it is properly connected to prevent leakages.

How do I reduce noise during high-speed spin cycles?

Ensure that loads are evenly balanced within the drum to reduce vibrations and noise.

Is there a child lock feature on this IFB Senorita Aqua SX Machine?

Appliances 1000RPM includes a child lock feature for added safety.

Can I configure different wash cycles based on fabric types?

IFB Appliances Senorita Aqua SX Machine 1000RPM offers multiple wash programs tailored for different types of fabrics.

Purifier MA-112

PH Tester HI 99104

Leave a Comment

Name

Email

Comment