Introduction

The Midea Washing Machine FP-90LTL105GETM-N1 is a top-loading, fully automatic washing machine designed for efficiency and convenience. With a generous capacity of 10.5 kg, it features eight wash programs to accommodate various laundry needs, including delicates and intensive cycles. The FP-90LTL105GETM-N1 is priced at approximately $399.00. The innovative Water Magic Cube pulsator ensures thorough cleaning while minimizing fabric wear. Its sleek design and user-friendly interface make it an excellent addition to any home. 

Technical Specifications

Unpacking

• Remove the machine from box and take out the foam board at the bottom.
• Take out the accessories inside the tub.
• Trial operation or washing on the foam cushion is strictly prohibited.
• Install the rat-proof base cover at the bottom of the machine.

Installation of drain hose 

• Completely insert the drain hose into the 1 washing machine drain outlet 

• Secure the connection, with the clamp provided

  

Placement of water drain hose

1. If the water drain hose shallbe extended, its length shallnot exceed 3 meters. Otherwise it will affect thewater discharging time.
2. The installed height of waterdrain hose shall not exceed 15 cm.

3. Do not bend the water drain hose and do not place it under the washer.

   

Installing Water Inlet Hose

(For Models with Double Screw Thread Inlet Pipe)

• Connect the water inlet pipe screw (with metallic ring) to the water faucet
• Connect the clamping nut (with rubber seal ring inside) of the water inlet hose to the washer inlet valve.
  Note: When tightening the clamping nut, evenly apply the force and do not twist the water inlet valve to avoid breaking the water inlet valve joint.

If the power cord is damaged, it must be replaced by the manufacturer, its service agent, similarly-qualified persons, in order to avoid hazards. The new hoses supplied with this product should be used; do not use old hoses. Opening at the base must not be obstructed by carpets or similar items. This appliance is for indoor use only.

Installation of Water Inlet Pipe

(For Models with Single Screw Thread Inlet Pipe)

Preparation Before Use

1. Make sure thet the washing machine is in a stable position
2. Install the water inlet hose.
3. Connect to  a power source
4. Open the water tap.
5. Put down the drain hose.

6. Put in clothes and suitable amount of detergent.

   

NOTE: Before washing, remove coins, keys, and other hard objects from pockets and fasten zippers to prevent damage to clothes and the tub.

Parts Identifications

All sketches in this manual are for reference only. Please refer to the product, for the actual appearance of the parts.

Accessories

Control Panel

1. Water Level
   Actual panel appearance may slightly vary. This illustration is a representative model.
2. Delay
   Press this button, to select the water level based on the clothes quantity. The indicator light is either steady or flashing, with each press of the button. The steady indicator light is for levels , 3, 5, & 7 while the flashing light is for levels 2, 4, 6, &8.
3. Start Pause
   Press this button to set the delay time (the number of hours that will elapse before washing starts ). The delay time is set just before pressing the Start button, Refer to “Special features” section of the manual, for more details.
   1. After program selection, press this button to start the wash cycle.
   2. Press this button to pause & resume the wash cycle.
   3. As an option, this button also activates the One Touch function. See Special Features section of this manual
4. Child Clock
   Press the “wash” and “rinse” at the same time to lock all the buttons on the control panel.
   Press the “wash” and “rinse” buttons at the same time to unlock the buttons.
5. Wash Rinse, Spin
   Press these buttons to select the washing time, number of rinses, and spinning time.
6. Program
   Press this button, to select the wash program. With each press of this button, the indicator either lights up steadily or flashes. The steady indicator light is for Mini wash, Jeans, Delicates, and Normal while the flashing light is for Drum dry, Quick, Bulky, & Intensive.
7. On/Off
   Turns the unit on and off

Description

The Midea Washing Machine FP-90LTL105GETM-N1 boasts a sleek and modern design that fits seamlessly into any home decor. The electronic control panel with an LED display makes it easy to navigate through the various wash programs. The machine’s large capacity drum is designed to minimize fabric wear and tear, ensuring your clothes stay in good condition for longer.

The washing machine also features an automatic detergent dispenser, which optimizes detergent usage and ensures a thorough clean. Additionally, the anti-vibration system reduces noise and vibration during operation, making it suitable for use at any time of day.

Quick Start

Program selection 

1. Press the “ON/OFF” button. 
2. Select the proper water level and other settings, as desired.
3. Press the Start/ Pause button

End of Program

• When the operation stops, the buzzer will sound continuously 6 times and then the power will be automatically cut off.
• Turn off the water tap.
• Although the power will be cut off automatically, the power plug must still be pulled out from the socket, for safety.

Operation

NORMAL Wash Program
The Normal wash program is the easiest, most convenient, and most common washing program. The user presses the power switch, presses the Start/Pause button, and the Normal washing program will start to work.

Procedure

1. Press the power switch.
2. Choose the appropriate water level, based on the wash load.
3. Press Start/Pause button.

Wash Program Customization
Users can freely set a variety of combinations for water level, wash time, number of rinses, and spin time, depending on their need.

Manual Setting Options

For Spin only

1. Press the Power button.
2. Press the Spin button to choose the spin time.
3. Press the Start/Pause button.

The washing machine will operate a single spin process.

For Wash only

1. Press the Power button.
2. Repeatedly press the spin button until the indicator light goes out. Press the Wash button to choose the wash time.
3. Press the Start/Pause button.

The washing machine will operate a single wash process.

For Wash and Rinse

1. Press the Power button.
2. Repeatedly press the Spin button until the indicator light goes out. Press the Rinse button and the Wash button to choose the setting desired.
3. Press the Start/Pause button.

The washing machine will operate the 'wash and rinse' process. For other process combinations, just choose the desired settings for water level, wash time, number of rinses, and spin time, then press the Start/Pause button.

NOTE

Close the lid when machine is running, otherwise, it will automatically stop working during the spin process and sound off a warning. The washer will not work when water does not reach the set water level.

Wash Settings (Program)

1. Normal
   For washing clothes with cotton fabric and daily wear.
2. Delicates
   Has a gentle wash action and slow spin speed for light fabrics such as silk.
3. Jeans
   For washing thick clothes and those with heavy stains.
4. Mini wash
   Ideal for washing small loads of laundry, using low water level.
5. Intensive
   Use this program, to wash heavily-soiled clothes.
6. Bulky
   Washing ability is strong and can wash large pieces of laundry.
7. Quick
   Washing time is short. Suitable for washing lightly-stained clothes.
8. Drum dry
   To dry the laundry without heating, to achieve the result of clothes being dried in a room.

Special Features

Delay
This function postpones the start of the washing process and the delay time is 1-24 hours. After selecting the wash settings, “long press” the Delay button repeatedly and the delay time will increase by 1 hour. When the display shows 24 hours and the Delay button is pressed, the display light will turn off and the Delay function turns off correspondingly.

Child Lock
This function can be activated only after the selected program starts.

Spin only

1. Press the ON/OFF button.
2. Press the Spin button to choose the spin time
3. Press Start/Pause button.

The washing machine will operate a single process.

Note: For wash only, follows steps in “Spin only” but press the wash button instead of the Spin button, to choose the wash time. Before pressing the Start/Pause button, press the Spin button repeatedly until the light goes out.

Tub clean
This function removes dirt accumulated on the inside and outside surfaces of the drum. In the standby mode, press Spin & Program buttons at the same time, to set to Tub clean. Afterwards, press Start/Pause button.

Water cycle (Rinse hold)
After the rinsing cycle is finished, water will not be drained and another set of clothes can be rinsed using the same water. To commence the Spin cycle, select the Spin time after rinsing is done and then press Start/Pause button.

Program pause and resumption
The program will stop if the Start/Pause button is pressed and will resume if this button is pressed again.

Automatic power shut off
If the Start/Pause button is not pressed after the ON/OFF button is pressed, power will automatically cut off after 10 minutes. When an operation stops, the buzzer will sound continously 6 times and then the power will automatically cut off.

One Touch
Follow steps no. 2 to 7 of Quick Wash, press ON/OFF button, then press Start/Pause button. The washing machine will automatically weigh the laundry, select the appropriate settings (water level, wash, time, rinse mode, spin time) and start the operation. No need to manually select the wash settings.

Automatic Balance

If the laundry is unevenly distributed in the tub before spinning, vibration is likely to occur during spinning. The washing machine can automatically adjust tub imbalance. If the unbalance sensor detects strong vibration, the program to balance the wash load will automatically commence.

When the machine adjusts imbalance, the “rinse” light flashes and water will be supplied to a set level. Adjustment takes about 1 minute and then water is drained. Afterwards, the spinning cycle will resume. The machine will make 2 attempts to adjust the imbalance. If imbalance still occurs after the 2nd attempt, an alarm will sound and the user needs to manually adjust the clothes distribution in the tub.

Fuzzy Logic Function

Fuzzy Logic Function
The “fuzzy” program automatically detects the amount of laundry and then selects the corresponding water level. The “fuzzy” control is deactivated in the following conditions:

1. If water is present in the tub at the start of operation and
2. If the user selects a certain water level at the start of operation.

Power Failure Memory Function
In case of a power failure, the operation during which the power was interrupted will be stored in the machine’s memory and when power resumes, the machine will continue operation where it left off.
Alarm function when the Top Lid is opened
If the Top Lid is opened during washing or spinning, an E3 alarm will be activated and operation will stop. Closing the Top Lid will deactivate the alarm and operation will automatically resume. When the Delay function has been activated, opening the Top Lid will also trigger the E3 alarm. Closing the Top Lid will cancel the alarm and the Delay function will resume.

Setup Guide

To set up your Midea Washing Machine FP-90LTL105GETM-N1, 

• Start by carefully unpacking the machine and removing all packaging materials. 
• Ensure the machine is placed on a level surface to prevent any imbalance during operation.
• Connect the water inlet hose to the water supply and secure it tightly. 
• Plug in the power cord and turn on the machine. 
• Follow the on-screen instructions to select your desired wash program and set any additional options such as temperature or spin speed.
• For initial use, it is recommended to run an empty cycle with a washing machine cleaner to remove any manufacturing residue.

Cleaning and Maintenance of the Washing Machine

End of Program

• The washing machine will alarm after the washing process to remind you to take out the laundry.
• After the sound, the machine will automatically go to its power-off state with no display and all lights will be off.
• Make sure to turn off the faucet and pull the power plug after every use to avoid water leakage or fire accidents

Maintenance

Use gentle cloth to wipe off the water and dirt on the surface of the machine after using it. Avoid using detergent, propellant and other chemicals when cleaning the surface of the machine to prevent damage to the plastic accessories.

Clean the Water Inlet

After long time use, the water inlet mesh bag may be blocked with dirt, clean it following there steps:

1. Switch on the power and the water faucet.

2. Let the washer work for 5 seconds so that the water flows into the tub through the water inlet hose.

   

Cleaning the Filter

After using the machine for a period, clean the filter accordingly.

1. Take out the lint filter.
2. Open the filter (for Magic Cleaning Filter) or reverse inside out the mesh bag (for normal filter) and wash it clean with water.

3. Restore and put back the filter.

   

Clean the lint filter in the drain pump (for machines with drain filter)

1. Drain the water out of the pump, use a container to collect
2. Loosen the pump cover counter-clockwise.
3. Take out the lint filter.
4. Clean the filter
5. Restore it and adjust the convex place to align at the pump hole.

6. Tighten the pump cover

   

Midea Washing Machine FP-90LTL105GETM-N1 Troubleshooting

If trouble occurs, contact Customer Care.
Only authorized service technicians are allowed to open and/or dismantle the machine.
If the machine does not function normally, an error indicator will be displayed at the control panel and an alarm will sound off. 

Check and correct, as follows:

Pros & Cons

Pros:

• High capacity suitable for large families
• Multiple wash programs for various fabric types
• Energy-efficient and eco-friendly
• Quiet operation with anti-vibration system
• User-friendly electronic control panel

Cons:

• Higher initial cost compared to some other models
• Large sizes may not fit in smaller spaces
• Slightly heavier than some other models

Customer Reviews

Customers have generally praised the Midea Washing Machine FP-90LTL105GETM-N1 for its robust performance and energy efficiency. Many appreciate the quiet operation and the variety of wash programs available. However, some users have noted that the initial setup can be a bit complex and the machine's size requires careful consideration of space.