Introduction 

The PowerBass Mid-Range Driver Speaker 4XL-65T is engineered to deliver exceptional sound quality, making it a perfect choice for audio enthusiasts. This speaker features a robust design that enhances mid-range frequencies, ensuring clarity and depth in music playback. With a power handling capacity that supports high volumes without distortion, it is suitable for various applications, from home audio systems to professional setups. The 4XL-65T is priced at approximately $99.99.

Specifications 

• Driver Size: 6.5 inches
• Power Handling: 150 Watts RMS, 300 Watts Peak
• Frequency Response: 100 Hz - 10 kHz
• Sensitivity: 92 dB
• Impedance: 4 Ohms
• Mounting Depth: 2.5 inches
• Weight: Approximately 2.5 lbs
• Materials: Durable polypropylene cone, rubber surround, and a sturdy steel basket

FEATURES

• Infinite Baffle Mid-Range Performance: Installs on any flat panel without the need for an enclosure.
• Shallow Mounting Depth: 4XL-80T: 2.625”, 4XL-65T: 2.25” Perfect for newer vehicles with large but narrow door panels.
• Bullet Style Phase Plug: Bullet design reduces inherent phase cancellations that occur between the dust cap and the speaker cone improving frequency response while at the same time adding depth and clarity to the sound stage.
• Treated Cloth Accordian Surround: Increases efficiency and reduces cone flexure at high power.
• KSV High Temperature 4-ohm Voice Coil: Specially designed Kapton high temperature voice coil formers ensure high power handling and precise linear excursion while maximizing thermal heat dissipation.
• Chrome Push Input Terminals: These high strength compression loaded speaker terminals insure maxi-mum current and power transfer.

The 4XL-80T and 4XL-65T are Mid-Range drivers designed for infinite baffle applications. They are not subwoofers and should not be used to reproduce frequencies below 90Hz.

WIRING GUIDELINES

Your PowerBass Xtreme 4XL Mid Range driver uses a single 4-ohm voice coil. It is important to know the limits of your amplifier to optimize its performance. You can very the impedance by altering the wiring configurations: Series, Parallel, or Series-Parallel. Choose the wiring diagram below that corresponds to the number of speakers in your system and the impedance stability of your amplifier.

Description

Premium materials are used in the construction of the Powerbass 4XL-65T Mid-Range Driver Speaker to guarantee longevity and excellent sound quality. Because the polypropylene cone is stiff and lightweight, it can reproduce sound accurately. The steel basket gives the driver a firm base, while the rubber surround offers flexibility and durability.
The effective operation of this speaker within its designated power range guarantees that it can withstand the demands of high-volume playback without distortion. Because of its specially designed frequency response, which emphasizes mid-range frequencies, it is perfect for boosting the clarity of instrumental elements and voices in your car's audio system.

INSTALLATION EXPERIENCE

Installation of PowerBass Xtreme speakers requires experience with a variety of mechanical procedures including enclosure construction.

This manual only provides general installation and operation instruc-tions. If you have any reservations about your installation skills, please contact your local Authorized PowerBass Xtreme dealer for assistance.

CHOOSING SPEAKER MOUNTING LOCATIONS

Choosing the correct speaker mounting location will have the greatest effect of the sound quality of the system. There are many different considerations needed when choosing the location(s) that best meet your needs. The locations must be large enough for the speakers to fit. Care is needed to ensure that the desired location will not affect either the mechanical or electrical operation of the vehicle.

WARNING! The use of silicone rubber to seal in a speaker will void the Warranty! If any sealing is needed in addition to the speaker’s gasket, use caulking cord or vinyl weather strip.

PREPARING FOR INSTALLATION

NOTE: The tools listed below may be required for basic installation.

• An electric drill with bits
• Saber, circular and jig saw
• Phillips-head and standard screwdrivers
• Wire strippers
• Crimping tool and needle-nose pliers

INSTALLATION PRECAUTIONS

NOTE: Proceed only if you are a qualified installer otherwise; let your dealer do it.

• Always wear protective eyewear when using tools.
• Turn off all stereo and other electrical devices before you begin.
• Disconnect the (-) negative lead from your vehicle’s battery.
• Keep the speakers in the package until final installation, and always rest it with the cone facing up. Never use force when installing a speaker.
• Locate all fuel lines, brake lines, oil lines, and electrical cables when planing your installation.
• Check to see if there is enough clearance behind the mounting surface before drilling holes or install-ing screws for proper speaker ventilation.
• Also make sure there’s enough front clearance for speaker cone excursion. Failure to do this could cause the cone to vibrate against any obstructing object.
• Use a utility knife to trim away fabric from the speaker mounting hole location before drilling.
• When running speaker wires through sheet metal, be sure to use grommets to properly insulate the wires from metal edges.

DOOR MOUNTING

When checking for possible speaker locations in the doors, check the operation of the window and all assemblies. There is also a stabilizer stop bar in between the door and the door jam. This bar prevents the door from opening too far.

REAR DECK MOUNTING

In rear deck installations, check the operation of the trunk suspension springs or tension bars. These tension bars move in the opening and closing of the trunk. You cannot be too cautious during this part of the instal-lation. In addition do not locate the speakers too close to the back of the rear deck. Installing the far screws may not be possible without removing the rear window.

INSTALLING THE MID-RANGE DRIVER

1. Determine where the speaker will be mounted. Make sure there is a flat area large enough for the speaker to fit properly. An uneven mounting surface can damage the driver.
2. Check to make sure the space you have selected for the speaker will not interfere with the operation of the vehicle.
3. Using the supplied template, mark the hole with a pen.
4. Cut the hole for the speaker. A hole can be cut either with a pair of metal tin snips, a saber or jig saw.
5. Run speaker wire (not included) to the speaker. Make sure to keep wires away from sharp metal or other rough edges. When passing through metal, use a grommet to protect the wires from sharp edges.
6. Pre drill the mounting holes using a 1/8” (3mm) drill bit.
7. Pull the wire though the speaker opening and connect to the speaker. Be sure to observe proper polarity.
8. Mount the speaker using screws.

RECOMMENDED ELECTRONIC CROSSOVER SETTING

There are two types of crossovers, passive and active. Passive crossovers (coils or inductors) are placed on the speaker leads between the amplifier and speaker (close as possible to speaker). An active crossover is an electronic filter that separates the audio signal fed to the amplifiers.

4XL-80T: For optimum performance of your 4XL-80T mid-range driver, we recommend using an active cross-over and setting the controls at 150Hz and HPF. If the electronic crossover has settings for bandpass/midrange usage, set the controls to 150Hz in HPF (High Pass) and 5KHz in LPF (Low Pass).

4XL-65T: For optimum performance of your 4XL-65T midrange driver, we recommend using an active cross-over and setting the controls at 200Hz and HPF. If the electronic crossover has settings for bandpass/midrange usage, set the controls to 200Hz in HPF (High Pass) and 5KHz in LPF (Low Pass).

Setup Guide

To set up the Powerbass 4XL-65T, 

1. First, make sure the 4-ohm speakers in your car are compatible with the audio system.
2. Disconnect the wires and take out the current mid-range speakers. Make sure to position and securely fasten the 4XL-65T in the appropriate speaker slots.
3. Attach the speaker cables to the corresponding terminals on the head unit or amplifier in your vehicle.
4. Make sure the external amplifier's impedance and power output settings are accurate if you're using one.
5. To maximize sound quality, test the speaker to make sure it is operating properly and change any equalization settings as needed.

PARAMETERS FOR 4XL MID RANGE

(due to Constant Improvement, Specification and Parameter are subject to change without notice)

Troubleshooting

If you encounter issues with the Powerbass 4XL-65T, here are some common problems and solutions:

• Here are some typical problems and fixes for the Powerbass 4XL-65T if you run into them:
• If there is no sound, make sure the wire connections are tight. Make that the head unit or amplifier is powered on and configured to the appropriate output channel.
• Distortion: To lessen the emphasis on the bass or treble, turn down the volume or change the equalization settings. Be careful not to overload the speaker beyond its power-handling capability.
• Vibration or rattling: To stop the speaker mount from moving, firmly fasten it. Examine the speaker and its surroundings for any loose parts.
• When working with electrical components, always take the appropriate safety precautions and seek expert advice if you have any questions about any aspect of the setup or troubleshooting procedure.

Always follow proper safety precautions when working with electrical components, and consult a professional if you are unsure about any part of the setup or troubleshooting process.

Pros & Cons

Pros

• Superior Sound: Provides crisp, in-depth mid-range tones for improved audio clarity.
• Sturdy Construction: Made from high-quality materials for enduring functionality.
• Effective Power Management: Capable of managing up to 300 watts of peak power input and 150 watts RMS.
• Installation Simplicity: Made for simple wiring and placement.

Cons

• Cost: Although reasonably priced, some customers might find it too expensive in comparison to less expensive solutions.
• Space Requirements: Some automobile models may provide a problem in providing sufficient mounting space.
• No Accessories Included: Users might have to buy extra wire or mounting hardware on their own.

Customer Reviews

Customers have given the PowerBass Mid-Range Driver Speaker 4XL-65T high marks for both its sturdy construction and superb sound quality. After installing these speakers, several people reported that the audio system in their cars had improved. But according to some users, the installation procedure might be a little difficult for people who have never done it before.

The absence of mounting hardware, which might raise the total cost, is a frequent grievance. Despite this, the majority of reviews concur that the 4XL-65T is a good buy due to its performance and longevity.

WARRANTY

PowerBass Xtreme Speakers are to be free of defects in material and workmanship for a period of one (1) year. The warranty is extended to three (3) years for parts and labor, if an Authorized PowerBass Xtreme Dealer completes the installation.