Installation: Waterpik Combo Shower Head XPB-135E-765ME Instruction Manual

Content

Overview

The Combo Shower Head XPB-135E-765ME combines a fixed-mount shower head with a removable handheld shower head. A two-way diverter lets you switch between the two water outlets, while the handheld spray selector provides several spray patterns for everyday bathing, rinsing hair, cleaning the shower area, or bathing children and pets.

This Waterpik shower system is designed for straightforward installation on an existing shower pipe. The kit uses a flexible hose, a diverter bracket, a fixed shower head, and a handheld shower head that rests in the bracket when it is not being used.

Specifications

Model: XPB-135E-765ME
Product type: Combination fixed and handheld shower head
Outlet control: Two-way diverter
Spray control: Rotating spray selector on the handheld shower head
Connection system: Threaded shower-pipe connection with washer-sealed hose connections
Included components: Diverter valve and bracket, fixed-mount shower head, handheld shower head, flexible shower hose, washers, and filter screen

Detailed Description

The main diverter assembly attaches to the existing shower pipe and supports the handheld shower head. Its control knob changes the water outlet between the fixed shower head and the handheld unit. Turn the knob in one direction to use the handheld spray and in the other direction to use the fixed shower head.

The handheld shower head includes a small spray selector lever. Move the lever left or right to choose among the available spray patterns. The fixed shower head remains attached to the front-facing threaded connector on the diverter.

The flexible hose has two different connection ends. The ridged connector attaches to the diverter bracket, while the smooth connector attaches to the handheld shower head. If the hose includes a vacuum breaker, connect the end marked for the shower bracket to the diverter bracket. Incorrect hose orientation can prevent water from flowing.

Safety

Set the household water heater to 120°F (48.9°C) or lower to reduce the risk of scalding and conserve energy.
Test the bath or shower water with your hand before entering.
Homes using high-efficiency or reduced-flow shower heads should have a pressure-balancing tub and shower valve with properly adjusted rotational-limit stops. Consult a qualified plumber if the valve type or setting is uncertain.
Use the shower system only for external bathing.
Some tap water and untreated well water may contain Naegleria fowleri. Follow local water-safety guidance, particularly where water may be warm or inadequately treated.
Place the handheld shower head securely in the diverter bracket so it cannot fall.
Do not pull or tug on the flexible hose. Excessive force can loosen the connections and cause the shower head to fall.
If the product malfunctions or becomes damaged, stop using it.

Setup and Operation

Before Installation

Gather a soft cloth and an adjustable wrench.
Remove the existing shower head and all old pipe tape.
Check that the washer from the old shower head has not remained inside the shower pipe. Use a thin tool, such as a pencil or screwdriver, to inspect the pipe; do not use your fingers.

Installation

Thread the diverter valve clockwise onto the shower pipe. Position the diverter bracket to the right and the two-way selector knob to the left.
Use an adjustable wrench to tighten the diverter nut until it is snug. Do not overtighten. If pliers are necessary, protect the nut with a cloth.
Attach the fixed shower head to the front-facing threaded connector on the diverter. Tighten this connection by hand only.
Identify the hose end with the ridged connector and hand-tighten it to the diverter bracket. If the hose has no ridged connector, attach either end to the bracket and tighten by hand. Proper hose placement is necessary for correct operation.
Attach the smooth hose connector to the handheld shower head. Use hand pressure only; do not use pliers or a wrench on the hose ends.
Place the handheld shower head in the diverter bracket.
Point both shower heads away from yourself, turn the water on fully, and inspect every connection for leaks. Tighten connections slightly if needed.

Changing the Water Outlet

Turn the diverter control knob clockwise or counterclockwise to change between the fixed shower head and the handheld shower head. The handheld spray selector is separate from the diverter: move its small lever left or right to change the spray pattern.

Vacuum Breaker Orientation

Local plumbing requirements may call for a backflow-prevention device when a handheld shower is installed. When the hose contains a vacuum breaker, the hose end with the identifying label must connect to the shower bracket. If connected in the wrong direction, the handheld shower head may not produce water.

Cleaning and Maintenance

Clean the spray nozzles when mineral deposits begin to restrict the water pattern. Gently rub the rubber nozzles on the face of the shower head to loosen deposits.

For heavier buildup, remove the shower head and place it face down in 1 to 2 cups of white vinegar for approximately 2 to 3 hours. Reinstall the shower head, then run water through each spray mode for 1 to 2 minutes to flush out the vinegar.

Do not use harsh chemicals, strong-duty cleaners, or abrasive materials. These products can damage the finish or components and may invalidate the warranty.

To clean the filter screen, unscrew it from the shower arm and rinse the diverter inlet. Reinstall the screen, then repeat the relevant installation steps to reinstall the shower head and bracket.

Troubleshooting

No Water Flows From the Installed Shower Head

Check that the washer from the previous shower head is not still inside the shower pipe.
Confirm that only one washer is installed inside the diverter nut.
Verify that the hose end with the vacuum breaker, when present, is attached to the diverter bracket.

Low Water Pressure or Missing Spray Patterns

Clean the shower head with a white-vinegar solution as described in the maintenance section.
Remove and rinse the filter screen.
Gently clear mineral deposits from the rubber spray nozzles.

Leak at the Shower Pipe and Diverter Nut

Confirm that the diverter nut contains only one washer.
Check that the diverter nut is properly seated and snug.
As a temporary thread-sealing measure, rub a bar of soap across the shower-pipe threads before reconnecting the diverter.

Diverter Assembly Rotates

Verify that the washer is installed inside the diverter nut.
Tighten the diverter nut an additional quarter-turn to half-turn.
Avoid excessive force, which can damage the connection or finish.

Warranty

The Combo Shower Head XPB-135E-765ME includes a lifetime limited warranty for the original purchaser. The warranty covers defects in materials and workmanship while the original purchaser owns the product.

Warranty coverage does not apply to abuse, misuse, alteration, or damage after purchase, including damage caused by tools or harsh chemicals. If the product has been discontinued, the manufacturer may provide a replacement considered reasonably similar. Labor, installation, and other consequential costs are excluded, and the manufacturer's responsibility is limited to the original purchase price.

Keep the purchase receipt because proof of purchase is required for warranty service. The warranty provides specific legal rights, and additional rights may vary by location. The warranty terms also require covered disputes to be handled through individual binding arbitration rather than court litigation, jury trial, or class action.

Pros & Cons

Pros: Combines fixed and handheld showering in one system.
Pros: Separate controls make it easy to change both the water outlet and handheld spray pattern.
Pros: The removable shower head is useful for targeted rinsing and cleaning.
Pros: The filter screen and rubber spray nozzles can be serviced when mineral buildup occurs.
Cons: Correct washer placement is essential for water flow and leak prevention.
Cons: The flexible hose can loosen or cause the handheld shower head to fall if pulled.
Cons: Mineral deposits may reduce pressure or block spray patterns without regular cleaning.

PDF

Faqs

How do I install the Combo Shower Head XPB-135E-765ME on an existing shower pipe?

Remove the old shower head and all pipe tape, then check inside the shower pipe to ensure its old washer has not remained there. Thread the diverter valve clockwise onto the shower pipe and tighten it snugly without overtightening. Attach the fixed shower head to the forward-facing threaded connector using hand pressure only. Connect the ridged hose end to the diverter bracket and the smooth hose end to the handheld shower head, then place the handheld unit in its bracket.

Which end of the hose connects to the diverter bracket?

The hose end with the ridged connector should be attached to the diverter bracket. Tighten this connection by hand. The smooth hose end connects to the handheld shower head, also by hand. Do not use pliers or an adjustable wrench on the hose connections, because excessive force can damage the fittings or cause leaks. If the hose does not have a ridged connector, either end may be connected to the diverter bracket, provided both connections are secure.

How do I switch between the fixed shower head and handheld shower head?

Use the two-way diverter control knob to choose the water outlet. Turn the knob clockwise or counterclockwise to direct water to the fixed shower head or the handheld shower head. The spray selector on the shower head controls the available spray patterns separately; move its small lever left or right to change the spray. Keep the handheld shower head seated properly in its bracket when it is not being held.

Why is there no water coming from the installed shower head?

First, turn off the water and inspect the shower pipe for the washer from the previous shower head. Remove it if necessary, using a thin tool rather than your fingers. Next, check that only one washer is inside the diverter nut. Also confirm that the hose is connected with its ridged end at the diverter bracket when applicable, especially if the hose includes a vacuum breaker. Incorrect washer placement or hose orientation can stop water flow.

What should I do if the Combo Shower Head has low water pressure or missing spray patterns?

Mineral buildup can restrict the spray openings and reduce water pressure. Gently rub the rubber spray nozzles on the shower head face to loosen deposits. For heavier buildup, remove the shower head and soak its face downward in white vinegar for approximately two to three hours. Reinstall it and run water through every spray mode to flush away the vinegar. If pressure remains low, remove and rinse the filter screen at the diverter entrance.

How do I clean the filter screen on this shower system?

Unscrew the filter screen from the shower arm or diverter entrance, then rinse the screen thoroughly with clean water to remove trapped sediment. Reinstall the screen securely, making sure it is seated correctly. Afterward, reinstall the shower head or bracket connections and check the system for normal flow. Avoid harsh chemicals, strong cleaners, and abrasive materials, since they may damage the finish or internal components.

How can I stop water leaking from the diverter nut connection?

Shut off the water and remove the diverter nut if needed to inspect the washer. Confirm that exactly one washer is installed inside the nut and that it is seated flat. Reassemble the connection and tighten it snugly, but do not overtighten. If the connection still seeps, lightly rub a bar of soap across the shower-pipe threads to help seal them, then retighten and test for leaks.

What safety precautions should I follow when using the XPB-135E-765ME?

Set the household water heater to no more than 120°F (48.9°C), and test shower water with your hand before bathing. Point all shower outlets away from yourself while first opening the water fully. Keep the handheld shower head properly seated in its bracket, and never pull or tug on the flexible hose because the unit could loosen and fall. Use the product externally only and stop using it if it becomes damaged or malfunctions.