Installation: Waterpik Hand Held Shower Head FN 20032320-F-AB Instruction Manual

Content

Overview

The Waterpik Hand Held Shower Head FN 20032320-F-AB is a flexible showering system designed for everyday bathing, easier reach, and assisted showering. Its handheld design connects to a flexible hose and wall-mounted bracket, while the pivoting head helps direct water where it is needed.

The shower head combines adjustable spray selection with an Easy Pause intensity control. This makes it practical for rinsing, bathing children, assisting another person, or reducing water flow while shampooing, shaving, or applying soap.

Specifications

Model: FN 20032320-F-AB
Head movement: 180-degree pivoting design
Water controls: Multiple spray settings, adjustable intensity, and pause trickle mode
Connections: Shower pipe, pivot ball, flexible hose, handheld shower head, and wall-mounted bracket
Mounting method: Adhesive wall bracket with an additional adhesive strip included
Vacuum breaker: May be included in the hose, depending on the supplied configuration

Detailed Description

The Hand Held Shower Head FN 20032320-F-AB uses a pivot ball at the shower-pipe connection to support positioning and water direction. A large hand-tightened nut secures this connection, while a filter screen helps catch particles before they reach the shower head.

The flexible hose connects between the lower bracket connection and the handheld shower head. The handheld unit can be placed in either available bracket position. Its head pivots through 180 degrees, allowing the spray to be aimed more comfortably during personal use or when helping someone else shower.

The spray selector provides access to the available spray patterns. A separate intensity switch controls the amount of water moving through the selected pattern. Moving the switch fully toward Pause produces a reduced trickle, while moving it toward Full Flow restores maximum flow for the selected setting.

Safety

Set the household water heater to 120°F (48.9°C) or lower to reduce the risk of scalding and conserve energy.
Test shower or bath water with your hand before entering or bathing another person.
Homes using high-efficiency shower heads should have a pressure-balancing tub and shower valve with properly adjusted rotational limit stops. Consult a qualified plumber if the valve type or adjustment is uncertain.
For external use only. Some tap water or untreated well water may contain Naegleria fowleri, a potentially dangerous amoeba.
Always seat the handheld shower head securely in its bracket to help prevent it from falling.
Do not pull, tug, or use the flexible hose to support body weight. Excessive force can loosen the connection or dislodge the shower head.
If the product becomes damaged or malfunctions, stop using it immediately.

Backflow Prevention

Some plumbing codes require a backflow prevention device, commonly called a vacuum breaker, when installing a handheld shower. If the hose includes one, identify the hose end marked for connection to the shower bracket and install that end at the bracket. Installing the hose in the wrong direction can prevent water from flowing.

Setup and Installation

Before beginning, remove the existing shower head and clear away all old pipe tape. Check inside the shower pipe for a leftover washer using a thin utensil such as a pencil or screwdriver. Do not use your fingers to search inside the pipe.

Thread the pivot ball onto the shower pipe by turning it clockwise. Hand-tighten the large nut so the connection is secure.
Attach either end of the flexible hose to the lower connection on the bracket. Turn the connector clockwise and tighten it by hand.
Connect the other hose end to the handheld shower head and hand-tighten the fitting.
Choose the wall-bracket location and clean the surface with a disposable towel or cloth moistened with a solution made from 50% isopropyl alcohol and 50% water. Finish by wiping the area with a dry cloth.
Remove the red-and-white protective liner from the adhesive on the rear of the wall bracket.
Press the wall bracket firmly against the shower wall. At room temperature, the adhesive reaches approximately 50% of its final strength after 20 minutes, 90% after 24 hours, and full strength after 72 hours.
Place the handheld shower head into either bracket position.

An adjustable wrench or pliers may be useful when removing the old shower head, although the new connections are designed for hand tightening. A soft cloth and isopropyl alcohol solution may also be needed. Pipe tape is not recommended for this installation.

Operation

Selecting a Spray Pattern

Rotate the selector lever at the base of the shower face to choose among the available spray settings. Adjust the shower head angle to direct the spray toward the desired area.

Adjusting Flow Intensity

Move the intensity switch fully toward Pause for a low trickle while lathering, shaving, or shampooing. Move it fully toward Full Flow for maximum flow in the selected spray mode. Intermediate switch positions allow the spray strength to be adjusted without changing the spray pattern.

Adjusting the Pivoting Head

Pivot the shower head within its 180-degree range to improve reach and comfort. Position the head before use when the unit is mounted, and keep the spray directed away from areas that should not be exposed to water.

Cleaning and Maintenance

Cleaning Spray Nozzles

Clean the spray face when mineral deposits begin to affect the openings. Gently rub the rubber nozzles with your fingers to loosen deposits.

For heavier buildup, remove the shower head and soak it face down in 1 to 2 cups of white vinegar for approximately 2 to 3 hours. Reinstall the shower head and operate every spray mode to flush out the vinegar. Repeat the process if necessary.

Cleaning the Filter Screen

Unscrew the pivot ball to access the filter screen. Rinse the screen by back-flushing it to remove trapped particles. During reassembly, ensure that the washer is seated correctly on top of the filter screen, then follow the first three installation steps to reconnect the shower head.

Do not use harsh chemicals, heavy-duty cleaners, or abrasive materials on any component. These substances can damage the finish or parts and may invalidate the warranty.

Troubleshooting

No Water Flow

Check that the washer from the previous shower head was removed from inside the shower pipe.
Confirm that only one washer is installed inside the pivot-ball connection.
If a vacuum breaker is included, verify that its marked hose end is connected to the shower bracket.

Low Pressure or Missing Spray Patterns

Clean the shower head and spray nozzles.
Clean the filter screen by removing particles through back-flushing.

Leak at the Shower-Pipe or Pivot-Ball Connection

Verify that only one washer is seated above the filter screen.
Make sure all old pipe tape has been removed from the shower pipe.
If needed, rub a bar of soap across the shower-pipe threads to help seal the threaded connection.
Review the installation sequence and hand-tighten the large nut securely without overtightening.

Bracket Is Difficult to Angle

Reposition the bracket so there is more leverage available when changing the spray angle. Avoid forcing the bracket or pulling on the hose.

Warranty

The product includes a limited lifetime warranty for the original purchaser against defects in materials and workmanship for as long as that purchaser owns the product. Warranty coverage depends on the product not being abused, misused, altered, or damaged after purchase.

Damage caused by tools or harsh chemicals is excluded. Labor, installation, and related consequential costs are not covered, and the manufacturer's responsibility does not exceed the original purchase price. Keep the sales receipt as proof of purchase for any warranty claim.

For United States purchases, the warranty terms also include limitations of liability and requirements for individual binding arbitration, including restrictions on court trials, jury trials, and class or representative actions where permitted by law.

Pros & Cons

Pros

180-degree pivoting head improves spray direction and handling comfort.
Handheld design supports personal and assisted showering.
Multiple spray settings provide flexible water coverage.
Easy Pause control can reduce flow during routine shower tasks.
Adhesive wall mounting avoids the need for drilled mounting holes.
Removable filter screen and vinegar-cleaning procedure support routine maintenance.

Cons

Adhesive mounting requires careful surface preparation and curing time.
Mineral deposits may require periodic nozzle, filter, and vinegar cleaning.
Incorrect vacuum-breaker hose orientation can stop water flow when that component is included.
The flexible hose should not be pulled or used to support the shower head.

PDF

Faqs

How do I install the Hand Held Shower Head FN 20032320-F-AB correctly?

Remove the old shower head and all pipe tape first. Check inside the shower pipe with a thin tool to ensure the old washer has not remained inside; do not use your fingers. Attach the pivot ball to the pipe and hand-tighten the large nut. Connect one hose end to the lower bracket and the other to the handheld shower head, tightening both connections by hand. Finally, place the head in either bracket.

Why is there no water flow after installing this handheld shower head?

Start by checking whether the old shower washer is still inside the shower pipe, because an extra washer can block water flow. Also inspect the pivot ball and confirm that only one washer is installed there. If the hose includes a vacuum breaker, connect the labeled vacuum-breaker end to the shower bracket; reversing the hose can prevent water from flowing. Recheck every connection for correct placement and hand-tightness.

How should I attach the adhesive wall mount bracket?

Choose a clean, suitable area on the shower wall and wipe it with a disposable cloth containing a 50 percent isopropyl alcohol and 50 percent water solution. Dry the surface completely with a clean cloth. Remove the red and white liner from the adhesive strip, then press the wall mount bracket firmly against the wall. The adhesive strengthens gradually, so avoid relying on its full holding force immediately after installation.

How long should I wait before using the adhesive shower bracket?

The adhesive bracket gains strength over time after it is pressed firmly onto the prepared shower wall. At room temperature, it reaches approximately half of its final bond strength after 20 minutes, about 90 percent after 24 hours, and full strength after 72 hours. Keep the bracket undisturbed during this period whenever possible. Once installed, place the handheld shower head securely in either bracket rather than hanging it from the hose.

How do I adjust the spray pattern and water pressure?

Use the spray selector to rotate through the available spray settings. The intensity control changes the water output independently of the selected spray pattern. Move the switch fully to the right for Pause, which reduces the stream to a trickle while you lather, shave, or shampoo. Move it fully left for Full Flow, or position it between the two ends to adjust the spray strength gradually.

What is the purpose of the 180-degree pivoting shower head?

The 180-degree pivoting head lets you direct the spray toward the area you need without repositioning the entire installation. Adjusting the angle can also make the handheld shower head more comfortable to hold during personal use or while helping another person shower. Move the head smoothly and place it securely in the wall or shower bracket when finished. Do not pull on the flexible hose to change its position.

How can I clean mineral deposits from the shower head?

When mineral buildup appears on the spray nozzles, gently rub the rubber nozzles on the shower head face to loosen the deposits. For heavier buildup, remove the shower head and soak it face down in white vinegar for approximately two to three hours. Reinstall it and run water through every spray mode to flush away vinegar. Do not use harsh chemicals, heavy-duty cleaners, or abrasive materials, which may damage the finish or components.

What should I check if the shower head leaks or has weak spray?

For a leak at the pivot-ball connection, verify that only one washer sits above the filter screen and that all old pipe tape has been removed from the shower pipe. A small amount of bar soap rubbed across the pipe threads can help seal the connection. If pressure is low or spray patterns are missing, clean the spray face and rinse the filter screen by removing it from the pivot ball and back-flushing away particles.