Installation: Waterpik Hand Held Shower Head Instruction Manual

Content

Overview

The Waterpik Hand Held Shower Head is designed for flexible, comfortable showering with a detachable spray head, wall bracket, flexible hose, and multiple spray settings. It suits users who want easier rinsing, targeted water flow, or a handheld option for bathing and cleaning.

Depending on the model, spray selection is controlled by a small lever, a rotating trim ring, an EasySelect® dial, or a sliding switch on the handle. Some versions also include a water-saving pause function.

Specifications

Product type: Handheld shower system
Spray control: Model-dependent lever, rotating ring, EasySelect® selector, or sliding switch
Water-saving feature: Pause control on selected models
Connections: Shower pipe, pivot ball, bracket, flexible hose, and handheld shower head
Filter: Removable filter screen inside the pivot ball
Recommended water-heater setting: 120°F (48.9°C) or lower
Warranty: Limited lifetime coverage for the original purchaser, subject to the stated conditions

Detailed Description

The system connects to the existing shower pipe through a pivot ball and bracket assembly. A flexible hose links the bracket to the detachable shower head, allowing the user to direct water where it is needed while the bracket provides hands-free use.

Important components include the shower pipe connection, large nut, pivot ball, filter screen, washer, hose connector, ridged hose connector, flexible hose, bracket, and handheld shower head. The filter screen helps catch particles before they reach the spray outlets.

Spray patterns vary by model. A small side lever may rotate from left to right, while other versions use a ring around the face or handle. EasySelect® models use a rotating selector, and sliding-switch models advance through spray settings each time the switch is moved upward.

Safety

Set the household water heater to no more than 120°F (48.9°C) to reduce scalding risk and conserve energy.
Test the bath or shower water with your hand before entering.
For high-efficiency or Ecoflow® models, a properly adjusted pressure-balancing shower valve with a rotational limit stop is recommended.
The shower head is intended for external use only. Some tap water and untreated well water may contain harmful microorganisms.
Always place the handheld shower head fully into the bracket so it cannot fall.
Do not pull or tug on the flexible hose, as this can loosen the connection and cause the shower head to fall.
If the product is damaged or operates abnormally, discontinue use.

Setup and Operation

Before Installation

Remove the existing shower head and all old pipe tape.
Check inside the shower pipe for a washer left behind. Use a pencil or screwdriver rather than your fingers.
Prepare an adjustable wrench or pliers if needed, along with a soft cloth.
Pipe tape is generally not recommended for this installation.

Installation

Attach the pivot ball to the shower pipe and tighten the large nut by hand until secure.
Connect the ridged hose connector to the bracket and hand-tighten it. If the hose has smooth connectors, use either end as appropriate and tighten it to the bracket by hand.
Attach the opposite hose end, including its rubber ring where supplied, to the handheld shower head. Tighten by hand.
Place the Hand Held Shower Head securely in the bracket before turning on the water.

Vacuum Breaker Installation

Some installations require a backflow-prevention device known as a vacuum breaker. If the hose includes one, connect the labeled vacuum-breaker end to the shower bracket. Installing the hose in the wrong direction can prevent water from flowing.

Spray Selection

On lever-controlled models, rotate the small lever left or right to change the spray.
On trim-ring models, turn the ring around the front of the shower head.
On EasySelect® models, rotate the selector ring in either direction.
On sliding-switch models, move the switch upward to advance to the next spray setting.

Pause and Flow Control

Selected models include a handle-mounted pause control that reduces the full spray to a water-saving trickle. The pause feature does not shut the water off completely because a small continuous flow may be required by plumbing regulations.

Cleaning and Maintenance

Removing Mineral Deposits

Clean the spray face when mineral deposits appear.
Gently rub the flexible rubber nozzles with your fingers to loosen buildup.
For heavier deposits, remove the shower head and soak the face downward in 1 to 2 cups of white vinegar for approximately 2 to 3 hours.
Reinstall the shower head and run water through every spray setting to flush out the vinegar. Repeat the process when necessary.

Cleaning the Filter Screen

Unscrew the pivot ball to access the filter screen. Rinse the screen from the reverse side to dislodge trapped particles. When reassembling the connection, ensure the washer is correctly seated on top of the filter screen, then follow the installation steps to reinstall the shower head.

Do not use harsh chemicals, heavy-duty cleaners, or abrasive products on any component. These substances can damage the finish or parts and may invalidate the warranty.

Troubleshooting

No Water Flow

Check that the old washer was removed from inside the shower pipe.
Verify that only one washer is installed in the pivot-ball connection.
If a vacuum breaker is included, confirm that its designated end is connected to the bracket.

Low Pressure or Missing Spray Patterns

Clean the shower head with the white-vinegar method.
Remove and rinse the filter screen.
Check the spray nozzles for mineral buildup and gently clear them.

Leak at the Pipe or Pivot Ball

Confirm that only one washer is seated above the filter screen.
Make sure all old pipe tape has been removed.
If necessary, rub a bar of soap across the shower-pipe threads to help seal the connection.

Bracket Is Difficult to Adjust

Loosen the bracket nut slightly, adjust the angle, and retighten it by hand. Avoid forcing the bracket.

Warranty

The limited lifetime warranty applies to the original purchaser for as long as that purchaser owns the product. Coverage addresses defects in materials and workmanship, provided the product has not been misused, abused, modified, or damaged after purchase.

Damage caused by tools or harsh chemicals is excluded. Labor, installation charges, and other related costs are not covered. If the original product has been discontinued, a similar replacement may be provided. Proof of purchase is required, and the warranty responsibility is limited to the original purchase price.

The warranty provides specific legal rights, while other rights may vary by location. Applicable warranty terms also limit certain implied warranties and exclude responsibility for direct, indirect, incidental, special, consequential, or exemplary damages where permitted by law.

Pros & Cons

Pros: Flexible handheld operation, multiple spray-selection methods, optional water-saving pause control, removable filter screen, and a secure hands-free bracket.
Cons: Features vary by model, mineral deposits require periodic cleaning, the pause function does not fully stop water flow, and incorrect hose or washer installation can prevent flow or cause leaks.

PDF

Faqs

How do I install a handheld shower head without causing leaks?

Remove the old shower head and clear away all pipe tape. Check inside the shower pipe with a pencil or screwdriver to ensure the old washer has not remained inside; never use your fingers. Attach the pivot ball to the pipe and tighten it securely by hand. Connect the hose to the bracket and handheld shower head, tightening both ends by hand. Avoid using pipe tape unless the product instructions specifically require it.

Why is no water coming from my handheld shower head?

First, check that the previous shower head’s washer is not still inside the shower pipe. Also confirm that only one washer is seated in the pivot ball, because an extra washer can block the connection. If the hose includes a vacuum breaker, make sure the labeled end is attached to the shower bracket; incorrect installation can stop water flow. Check that every connection is properly tightened and that the hose is not kinked.

How can I change the spray settings on a handheld shower head?

The spray selector depends on the model. Some handheld shower heads use a small lever that moves left or right, while others use a rotating trim ring around the spray face. EasySelect models may have a rotating ring on the handle. Models with a sliding switch change to the next spray pattern each time the switch moves upward. Move the selector gently rather than forcing it if the setting feels stiff.

What should I do if the handheld shower head has low water pressure?

Low pressure or missing spray patterns may result from mineral buildup in the spray openings or debris in the filter screen. Gently rub the rubber nozzles on the shower head face to loosen deposits. If the problem continues, remove the filter screen from the pivot ball and rinse it by back-flushing to push particles out. Reinstall the screen and washer correctly, ensuring the washer sits above the filter.

How do I clean mineral deposits from a handheld shower head?

For light buildup, gently rub the rubber spray nozzles with your fingers to release mineral deposits. For heavier deposits, remove the shower head and place it face down in white vinegar for about two to three hours. Reattach it afterward and run water through every spray mode to flush out the vinegar. Repeat if necessary. Do not use harsh chemicals, heavy-duty cleaners, or abrasive products because they can damage the finish and components.

What causes a handheld shower head connection to leak?

A leak at the pipe or pivot-ball connection may indicate an incorrectly positioned washer, leftover pipe tape, or a loose connection. Confirm that only one washer is seated above the filter screen and remove any old tape from the shower pipe threads. Tighten the connection by hand. If needed, rubbing a small amount of bar soap across the pipe threads can help form a temporary seal. Inspect the connection again after turning on the water.

How do I safely use the pause feature on a handheld shower head?

Some handheld shower heads include a handle switch or button that reduces full water flow to a water-saving trickle. It is not designed to shut the water off completely; a small continuous flow may remain. Use the pause setting while applying soap or adjusting your position, then return the control to full flow before rinsing. Operate the switch gently and avoid treating it as a replacement for the shower valve.

What safety precautions should I follow with a handheld shower head?

Set the water heater to 120°F (48.9°C) or below and test the shower water with your hand before bathing. Keep the handheld shower head securely seated in its bracket so it cannot fall. Do not pull or tug the flexible hose, since this can loosen a connection and cause the shower head to drop. For high-efficiency models, a properly adjusted pressure-balancing shower valve with rotational limits is recommended for additional protection from sudden temperature changes.