Introduction

The Philips TAT2206 headphones are true wireless earbuds designed for a seamless audio experience, perfect for music lovers and those who frequently take calls. With a lightweight design and an IPX4 rating, these headphones are sweat and splash resistant, making them ideal for workouts or outdoor use. They offer up to 18 hours of total playback time with the charging case, and feature Bluetooth 5.0 for stable connectivity. The cost of the Philips TAT2206 is approximately $49.99

Technical data

• Music time: 6 hours
• Talk time: 6 hours
• Standby time ˙ 200 hours Charging time: 2 hours
• Lithium-ion battery 55 mAh on each earpiece, Lithium-ion battery 350 mAh on charging box
• Bluetooth version: 5.0
• Compatible Bluetooth proÿles:
  • HFP (Hands-Free Proÿle)
  • A2DP (Advanced Audio Distribution Proÿle)
  • AVRCP (Audio Video Remote Control Proÿle)
• Supported audio codec: SBC
• Frequency range: 2.402-2.480GHz
• Transmitter power: < 10 dBm
• Operating range: Up to 10 meters (33 feet)
• Auto power o°
• USB-C port for charging
• Low battery warning: available

Note

Speciÿcations are subject to change without notice.

Important safety instructions

Danger
To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.

Be sure to observe the following guide-lines when using your earpieces.

• Listen at reasonable volumes for reasonable periods of time.
• Be careful not to adjust the volume continuously upwards as your hearing adapts.
• Do not turn up the volume so high that you can’t hear what’s around you.
• You should use caution or tempo-rarily discontinue use in potentially hazardous situations.
• Excessive sound pressure from earpieces and headphones can cause hearing loss.
• Using headphones with both ears covered while driving is not recom-mended and may be illegal in some areas while driving.
• For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.

General information

To avoid damage or malfunction:

Caution

• Do not expose headphones to excessive heat.
• Do not drop your headphones.
• Headphones shall not be exposed to dripping or splashing. (Refer to the IP rating of specific product)
• Do not allow your headphones to be submerged in water.
• Do not charge your headphones when the connector or socket is wet.
• Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
• If cleaning is required, use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
• The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like.
• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• To achieve the specific IP rating, the charging slot cover must be closed.
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting a battery, can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.

Operating and storage temperatures and humidity

• Store in a place where the temperature is between -20°C (-4°F) and 50°C (122 °F) with up to 90%relative humidity.
• Operate in a place where the temperature is between 0°C (32°F) and 45°C (113 °F) with up to 90%relative humidity.
• Battery life may be shorter in high or low-temperature conditions.
• Replacement of a battery with an incorrect type risks severely damaging the headphones and the battery (for example, in the case of some lithium battery types).

Your True wireless earpieces

To fully benefit from the support that Philips offers, register your product at https://www.philips.com/welcome. With this Philips True wireless earpieces, you can:

• enjoy convenient wireless handsfree calls;
• enjoy and control wireless music;
• switch between calls and music.

What's in the box

1. Philips True wireless earphones Philips TAT2206
2. Replaceable rubber ear caps x 3 pairs
3. USB-C charging cable (for charging only)

Other devices

A mobile phone or device (e.g. notebook, tablet, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible with the earpieces.

Overview of your True Wireless earpieces

1. LED indicator (Earpieces)
2. Multi-function button
3. Microphone
4. LED indicator (charging box)
5. USB-C charging slot

Description

The Philips Headphones TAT2206 features a sleek and durable design, making them both stylish and long-lasting. The premium leatherette ear cushions provide superior comfort during extended listening sessions, while the adjustable metal headband ensures a secure fit. The headphones are equipped with advanced 40mm dynamic drivers that deliver rich, detailed sound across the entire frequency spectrum.

The TAT2206 also includes a built-in microphone for clear voice calls and seamless integration with voice assistants. The headphones support both wired and wireless connectivity, offering flexibility in how you choose to listen to your music.

Get started

Charge the battery

Note

• Before you use your earpieces for the first time, place the earpieces in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime.
• Use only the original USB-C charging cable to avoid any damage.
• Finish your call before charging the earpieces, as connecting the earpieces for charging will power the earpieces off.

Charging

Connect one end of the USB cable into the charging box, and another end into the power source. The charging box starts charging.

• Charging process is verified by the LED light on the front panel.
• When the charging box is fully charged, the light goes off.

Tip

• The charging box serves as a portable backup battery for charging the earpieces. When the charging box is fully charged, it supports 2 times full recharge cycle for the earpieces.
• Normally, a full charge takes 2 hours (for the earpieces or charging box) by USB cable.

How to Pair

Pair the earpieces with your Bluetooth device for the first time

1. Make sure that the earpieces are fully charged.

2. Open the top cover from charging box.

   

   • The LED on both earpieces flashes in white & blue alternately.
   • The earpieces are now in pairing mode and are ready to pair with a Bluetooth device (e.g. a mobile phone)
3. Turn on the Bluetooth function of your Bluetooth device.
4. Pair the earpieces with your Bluetooth device. Refer to the user manual of your Bluetooth device.

Note: After powering on, if the earpieces cannot find any previously connected Bluetooth device, it will automatically switch to pairing mode.

The following example shows you how to pair the earpieces with your Bluetooth device.

1. Turn on the Bluetooth function of your Bluetooth device, and select Philips TAT2206.
2. Enter the earphone's password “0000” (4 zeros) if prompted. For those Bluetooth devices featuring Bluetooth 3.0 or higher, no need to enter a password.

Single earpiece (Mono mode)
Take either right or Left earpiece out from the charging box for Mono use. The earpiece will power on automatically. There will be a voice “Power on” from earpiece.

Note

Take the second Earpiece from the charging box and they will pair each other automatically.

Pair the earpieces with another Bluetooth device
If you have another Bluetooth device that you want to pair with the earpieces, make sure the Bluetooth function in any other previously paired or connected devices are turned off. Press and hold over 5 seconds both left & right side simultaneously with the earpiece on ear the, release when the Pairing voice prompt is heard.

Note

The earpieces store 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one.

Setup Guide

To operate the Philips Headphones TAT2206, follow these steps:

1. Unbox the headphones and inspect for any damage.
2. Charge the headphones if using wireless mode (charge for at least 2 hours for the first use).
3. Pair the headphones with your device via Bluetooth or connect using the 3.5mm audio jack.
4. Adjust the headband to fit comfortably on your head.
5. Start playing your preferred music or content.

For assembly, simply attach the earcups to the headband if they were detached during shipping. Configuration settings can be accessed through the companion app available for download on your smartphone or tablet.

Use your headphones

Connect the earpieces to your Bluetooth device

1. Turn on the Bluetooth function of your Bluetooth device.
2. Open the top cover from the charging box.
   • The blue LED flashes.
   • The earpieces will search the last connected Bluetooth device and reconnect to it automatically. If the last connected device is not available, the earpieces will enter pairing mode.

Tip

1. The earpieces cannot connect to more than 1 device at the same time. If you have two paired Bluetooth devices, only turn on the Bluetooth function of the device that you want to connect.
2. If you turn on the Bluetooth function of your Bluetooth device after turning on the earpieces, you have to go to the Bluetooth menu of the device and connect the earpieces to the device manually.

Note

• The earpieces cannot connect to more than 1 device at the same time. If you have two paired Bluetooth devices, only turn on the Bluetooth function of the device that you want to connect.
• If you turn on the Bluetooth function of your Bluetooth device after turning on the earpieces, you have to go to the Bluetooth menu of the device and connect the earpieces to the device manually.

Power on/off

Manage your calls and music

Music control

Call control

LED indicator status

Voice Assistant 

Reset the earpieces

If you encounter any pairing or connection issue, you can follow the following procedure to reset your headset.

1. On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT2206 from the device list.
2. Turn off the Bluetooth function of your Bluetooth device.
3. Press once on both earpieces, and then press and hold for 5 seconds.
4. After Blue LEDs finish flashing, return the earpieces to the charging box & close the lid.
5. Follow steps in “Use your earpieces-Connect the earpieces to your Bluetooth device.”
6. Pair the earpieces with your Bluetooth device, select Philips TAT2206.

Notice

Declaration of conformity
Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can ÿnd the Declaration of Conformity on www.p4c.philips.com.

Disposal of your old product and battery
Your product is designed and manufactured with high-quality materials and components, which can be recycled and reused. This symbol on a product means that the product is covered by European Directive 2012/19/EU. This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an o˛cial collection point or a Philips service center to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

Remove the integrated battery

If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones.

• Make sure the earpieces is disconnected from the charging box before removing the battery.

  

• Make sure the charging box is disconnected from the USB charging cable before removing the battery.

  

Troubleshooting

My Bluetooth earpieces do not turn on
The battery level is low. Charge the earpieces.

I cannot pair my Bluetooth earpieces with my Bluetooth device
The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earpieces.

Pairing does not work

• Put both earpieces into the charging box.

• Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.

• On your Bluetooth device, delete “Philips TAT2206” from the Bluetooth list.

• Pair your earpieces (see ‘Pair the earpieces with your Bluetooth device for the ÿrst time’ on page 5).

The Bluetooth device cannot find the earpieces

• The earpieces may be connected to a previously paired device. Turn o° the connected device or move it out of range.

• Pairing may have been reset or the earpieces have been previously paired with another device. Pair the earpieces with the Bluetooth device again as described in the user manual. (see ‘Pair the earpieces with your Bluetooth device for the ÿrst time’ on page 5).

My Bluetooth earpieces are connected to a Bluetooth stereo-enabled mobile phone, but music only plays on the mobile phone speaker
Refer to the user manual of your mobile phone. Select to listen to music through the earpieces.

The audio quality is poor and crackling noise can be heard

• The Bluetooth device is out of range. Reduce the distance between your earpieces and Bluetooth device, or remove obstacles between them.

• Charge your earpieces.

The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all
Make sure your mobile phone not only supports (mono) HFP but also supports A2DP and is BT4.0x (or higher) compatible (see ‘Technical data’ on page 10).

My Bluetooth earpieces won’t pair and won’t respond

• Put earpieces into the charging box.

• Reset your earpieces. See “Reset the earpieces” on page 9.

Philips and the Philips Shield Emblem have registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its a˛liates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product.

Pros & Cons

Pros:

• Excellent Sound Quality: Clear and balanced audio reproduction.
• Comfortable Design: Premium leatherette ear cushions and adjustable metal headband.
• Long Battery Life: Up to 24 hours of playback on a single charge.
• Flexible Connectivity: Supports both wired and wireless connections.

Cons:

• No Active Noise Cancellation: Only passive noise isolation is provided.
• No Water Resistance: Not designed for use in wet conditions.
• Heavy: The headphones are slightly heavier compared to some other models.

Customer Reviews

Customer reviews highlight the exceptional sound quality and comfort of the Philips Headphones TAT2206. Many users appreciate the long battery life and flexible connectivity options. However, some users have noted that the lack of active noise cancellation and water resistance are minor drawbacks.

The most common complaints include the weight of the headphones and the absence of additional features like customizable sound profiles or waterproofing.