Introduction

The Westinghouse Electric Pressure Washer EPX2000 is a powerful and efficient cleaning solution designed for various outdoor tasks. With a maximum pressure of 2000 PSI and a flow rate of 1.5 GPM, it effectively tackles dirt and grime on surfaces like patios, driveways, and vehicles. This electric pressure washer features a lightweight design, a 35-foot power cord, and a 15-foot high-pressure hose for extended reach and convenience. The EPX2000 is priced at approximately $149.99.

Package Contents

Product Specifications

Preparation

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. 

Estimated Assembly Time: 10 minutes

Assembly Instructions

1. Slide caster (C) tab into slot on bottom corner of power washer unit (D). Repeat for the remaining casters.

2. Slide hose holder (E) onto tab on the right side of power washer unit (D).

   

3. Slide foam cannon bracket (K) onto tab on back of power washer unit (D).
4. Slide upper spray gun holder (A) tab into slot on left side of power washer unit (D).

5. From below, slide lower spray gun holder (B) tabs into slots on bottom left side of power washer unit (D).

   

6. Hold back the collar at one end of the end of the hose (G). Push firmly to connect hose fitting to the water outlet tube on the front of the power washer unit (D). Twist the collar clockwise to secure. Confirm hose is locked into the water outlet by slightly pulling on the hose. 
   Note: DO NOT use pliers or locking pliers to tighten.
7. Push firmly to connect hose fitting (G) to spray gun (H). Confirm hose is locked into spray gun by slightly pulling on them.

8. To remove the hose, push the button on lower front of gun to release the hose (G) connection from the spray gun (H).

   

9. To lock the trigger of the spray gun (H), aim the gun away from you and push the trigger button (I). After doing so, squeeze or pull the trigger to make sure it is locked and will not move. ALWAYS keep spray gun (H) locked when not in use.
10. Insert lance (J) into spray gun (H) and turn clockwise to tighten (DO NOT overtighten).
    Note: ALWAYS engage the safety lock (I) when changing lances ensure that they do not accidentally eject with force during removal.

11. Attach a garden hose to the garden hose adapter on the back of the power washer unit (D).
    Note: Flush out garden hose before connecting to garden hose adapter.
    Assembly is now complete. Read and observe all safety instructions before turning on the power washer.

    

Description

The Westinghouse Electric Pressure Washer EPX2000 boasts a sturdy and compact design, making it easy to maneuver and store. The 2000W electric motor delivers consistent high pressure, ensuring effective cleaning without the need for gasoline. The pressure washer comes with a variety of nozzles, allowing users to adjust the spray pattern according to the task at hand. The long hose and cord provide ample reach, reducing the need for frequent repositioning.

The EPX2000 also features a built-in detergent tank, enabling the use of cleaning solutions directly from the machine. This model is designed with safety in mind, including features like automatic shut-off and a secure locking mechanism to prevent accidental start-ups.

Electric Pressure Washer  Operating Instructions

1. Turn on water supply at the faucet.
2. Make sure the “ON/OFF” switch is in the “OFF” position. The power switch has international symbols: On (|) Off (O).
3. Completely unwind the power cord and plug into a grounded 120 volt outlet.
4. Release the spray gun safety lock (I) on the spray gun (H). Point the spray gun in a safe direction and squeeze the trigger until there is a steady stream of water, releasing water and air out of the hose. Lock the spray gun.
5. Turn the power switch to the “ON” (|) position. The unit will run on for 1 - 2 seconds and shut off. This is a normal function of the auto-start feature.
6. Begin power washing by squeezing the trigger all the way into the handle.
7. Release the trigger to stop the power washer.
8. Allow the motor to come to a complete stop before squeezing the trigger again.
9. Squeezing the trigger rapidly will cause the auto-start feature to miss an on/off cycle and may prevent the washer from turning on. Use slow, deliberate trigger pulls to avoid this.
10. ALWAYS test a small area to avoid damaging the surface.

Using High/Low Nozzle 
The spray pattern and intensity can be adjusted for each task by twisting the spray nozzle at the far end of the lance.

• Twist the nozzle head clockwise for the high pressure (pencil stream) setting.

• Twist the nozzle head counter clockwise for the low pressure (fan spray) setting.

  

Operation Tips 

• When using detergent, fill bottle with a properly formulated detergent-to-water ratio, following instructions on the container.
• It is normal to hear the motor run intermittently when the trigger is not being squeezed. The pump is priming itself to operate when the trigger is squeezed.
• Turn off the power washer if not being used after five minutes.
• The O-rings in the hose should be cleaned regularly and lubricated with non-water soluble grease such as petroleum jelly.
• Keep the cleaning wire nearby for unclogging the spray nozzle.

How to Avoid Damaging Surfaces

• Damage to surfaces being cleaned occurs when the impact force of the water pressure exceeds the durability of the surface. Bare wood can be penetrated; paint can be peeled off, etc. You can vary the force of the power washer by adjusting:
  1. The angle of the nozzle to the surface being cleaned.
  2. The distance from the nozzle to the surface being cleaned.
• NEVER use a narrow, high-pressure stream of water on soft surfaces.

Cleaning Garden Hose Adapter 
The screens inside the garden hose adapter should be cleaned periodically.

1. Rinse with clean water.
2. Place back into the adapter.

Using the Foam Cannon

1. Detach the lance from the high pressure gun.
2. Unscrew fluid tank from foam cannon valve assembly.
3. Fill fluid tank with water (for best results, use warm water.)
4. Add 1-3 ounces of your favorite detergent to the fluid tank.
5. Attach fluid tank to foam cannon valve and attach assembly to the gun. Use the control knob to change the flow of soap + (more) or - (less).

6. When finished, run clean plain water through the pressurized foaming system to purge soap from the internal components.
   Flush with hot water for added cleansing power.

   

Setup Guide

To set up the Westinghouse Electric Pressure Washer EPX2000, 

• Start by unpacking all the components and ensuring all parts are included. 
• Connect the hose to the machine and the spray gun, then attach the desired nozzle. 
• Plug in the power cord and ensure it is securely locked into place. Fill the detergent tank if using cleaning solutions. 
• Turn on the machine and adjust the nozzle settings as needed for your specific cleaning task.
• For assembly, follow the manufacturer's instructions carefully. 
• Typically, this involves attaching the handle, connecting the hose and spray gun, and securing any other accessories. 
• Always refer to the user manual for specific steps and safety precautions.

Care and Maintenance about Westinghouse EPX2000

Cleaning Nozzles

A clogged or partially clogged nozzle can cause significant reduction of water pressure coming out of the nozzle and/or cause the unit to pulsate while spraying.

1. Turn off the unit.
2. Turn off the water supply to the unit.
3. Relieve any pressure trapped in the hose by squeezing the trigger 2-3 times, and then lock the spray gun by pushing the lock button from left to right.
4. Remove the lance from the spray gun
5. Using the nozzle tip cleaner provided (or an unfolded paper clip), insert the wire into the nozzle hole and move back and forth until debris is dislodged.
6. Tap quick connect end of lance on hard surface several times

7. Back flush water through the nozzle using garden hose and highest pressure available (either standard water nozzle or use your thumb over the nozzle to create water pressure for back flush).

   

Storage

1. When the pressure washing session is complete, turn off the power switch.
2. Unplug the power cord from the outlet.
3. Turn off the water supply. Pull the trigger on the spray gun 2-3 times to drain out excess water and to release any remaining water pressure.
4. Disconnect the garden hose adapter from the water inlet. DO NOT allow the power washer to run with no water flowing through it.
5. It is recommended to run pump saver through the pump and high pressure hose.
   • 5a. Install the pump saver by attaching the bottle to the garden hose adaptor and open the valve on the bottle.
   • 5b. Plug in the power-cord and turn the pressure washer on/off switch to the “on” position and pull the trigger for 5 seconds in order to activate the pump and purge the pump saver through the pump system and hose.
   • 5c. Once you are done, turn the on/off switch to the “off” position, pull the trigger to release the internal pressure and then disconnect the hose and accessories from the power washer.
6. Remove hose from spray gun.
7. Remove lance from spray gun. Place the gun and lance in the holders on the side of the unit.
8. Hook the power cord around the power cord holder.

Troubleshooting

THREE-YEAR LIMITED WARRANTY

• Parts and labor will be fully covered for a period of one year from the date of purchase.
• Parts only will be fully covered for a period of two years from the date of purchase.

To ensure hassle-free warranty coverage, it is important that you register your Westinghouse electric pressure washer online at www.wpowereq.com,

Replacement Parts

Westinghouse Electric Pressure Washer EPX2000 Pros & Cons

Pros

• High Pressure Output: Delivers up to 2030 PSI for effective cleaning.
• Easy to Use: User-friendly design with multiple nozzle settings.
• Eco-Friendly: Electric power reduces noise and environmental impact.
• Affordable: Priced competitively compared to gas-powered models.
• Compact Design: Easy to store and transport.

Cons

• Limited Reach: Dependent on power cord length and availability of outlets.
• Nozzle Durability: Nozzles may need frequent cleaning or replacement.
• While compact, it can be heavy for some users.
• Regular maintenance is required to ensure optimal performance.

Customer Reviews

Customers praise the Westinghouse Electric Pressure Washer EPX2000 for its powerful performance and ease of use. Many appreciate its eco-friendly design and the variety of nozzle settings. However, some users have reported issues with nozzle durability and the weight of the machine. Overall, it has received positive feedback for its value and effectiveness in various cleaning tasks.

Common complaints include the need for frequent nozzle cleaning and the occasional leakage from worn-out seals. However, these issues are generally resolved through regular maintenance and part replacement as needed.